1、1 ECHNICAL n GSM 02.22 July 1998 Version 5.4.0 Source: SMG ICs: 33.020 Reference: RGTSBMG-O 10222QR3 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) Digital cellular telecommunications system (Phase 2+); Personalisation of GSM Mobile Equipment (ME
2、) Mobile functionality specification (GSM 02.22 version 5.4.0 Release 1996) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE internet: secretaria
3、tetsi.fr - http:/www.etsi.fr - http:/www.etsi.org Tel.: +33 4 92 94 42 O0 - Fax: +33 4 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunicati
4、ons Standards Institute 1998. All rights resewed. Page 2 GSM 02.22 Version 5.4.0 Release 1996: July 1998 Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, pleas
5、e write to “ETSI Standards Making Support Dept.“ at the address shown on the title page. STD-ETSI GSM 02.22-ENGL 1778 3400855 0332b53 Ab5 Page 3 GSM 02.22 Version 5.4.0 Release 1996: July 1998 Contents Foreword . 5 1 Scope 7 2 Normative references 7 3 Definitions and abbreviations 8 3.1 Abbreviation
6、s . 8 3.2 Definitions 8 4 General description . 9 5 Network personalisation 10 5.1 Network personalisation . 10 5.1.1 Operation of network personalised ME . 10 5.1 -2.1 Personalisation cycle . 10 5.1.2 Network.personalisation cycle . 10 5.1.2.2 De-personalisation cycle 11 5.2 Network subset personal
7、isation . 11 5.2.1 5.2.2 Operation of Network subset personalised ME . 11 Network subset personalisation cycle . 12 5.2.2.1 Personalisation Cycle 12 5.2.2.2 De-personalisation cycle 12 6 SP personalisation 13 6.2 SP personalisation cycle 13 6.1 Operation of SP personalised MES 13 6.2.1 Personalisati
8、on cycle . 13 6.2.2 De-personalisation cycle . 14 7 . Corporate personalisation . 14 7.1 7.2 Operation of corporate personalised MES . 15 Corporate personalisation cycle . 15 7.2.1 Personalisation cycle . 15 7.2.2 De-personalisation cycle . 16 8 SIM personalisation . 16 8.1 8.2 Operation of SIM pers
9、onalised ME 16 SIM personalisation cycle 17 8.2.1 Personalisation cycle . 17 8.2.2 De-personalisation cycle . 17 9 Over the air de-personalisation cycle 17 10 Disable Personalisation . 18 11 Manufacturer personalisation and de-personalisation 19 12 Automatic personalisation . 19 13 Personalisation C
10、ycle Restrictions 19 14 Security 19 Annex A (normative): Technical information . 21 STD-ETSI GSM 02.22-ENGL 1778 3400855 033265g 7Tl Page 4 GSM 02.22 Version 5.4.0 Release 1996: July 1998 A.l GID1 and GID2 files . . 21 A.2 Emergency calls only mode . . 21 A.3 Co-operative Network List . . 21 A.4 Ove
11、r-the-air de-personalisation . . 21 Annex B (informative): Change history . 23 History . 24 Page 5 GSM 02.22 Version 5.4.0 Release 1996: July 1998 Foreword This Global System for Mobile communications Technical Specification (GTS) has been produced by the Special Mobile Group (SMG) of the European T
12、elecommunications Standards Institute (ETSI). This GTS prvides functional specifications of five features to personalise GSM Mobile Equipment (ME) within the digital cellular telecommunications system. The contents of this GTS are subject to continuing work within SMG and may change following formal
13、 SMG approval. Should SMG modify the contents of this GTS it will then be republished by ETSI with an identifying change of release date and an increase in version number as follows: Version 5.x.y where: x the second digit is incremented for all other types of changes, .e. technical enhancements, co
14、rrections, updates, etc. y the third digit is incremented when editorial only changes have been incorporated in the specification; - STD.ETS1 GSM 02.22-ENGL 1998 I3400855 0332b5b 57Li U Page 7 GSM 02.22 Version 5.4.0 Release 1996: July 1998 1 Scope This Global System for Mobile communications Techni
15、cal Specification (GTS) provides functional specifications of five features to personalise GSM Mobile Equipment (ME). These features are called: - Network personalisation; - Network subset personalisation; - Service Provider (SP) personalisation; - Corporate personalisation; - Subscriber Identity Mo
16、dule (SIM) personalisation. This GTS specifies requirements for MES which provide these personalisation features. These optional personalisation features are stated in GSM 02.07 2. 2 Normative references This GTS incorporates by dated and undated reference, provisions from other publications. These
17、normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this GTS only when incorporated in it by amendment or revision. For undated references, th
18、e latest edition of the publication referred to applies. GSM 01.04 (ETR 350): “Digital cellular telecommunications system (Phase 2+); Abbreviations and acronyms“. GSM 02.07 (ETS 300 906): “Digital cellular telecommunications system (Phase 2+); Mobile Stations (MS) features“. GSM 02.1 1 (ETS 300 921)
19、: “Digital cellular telecommunications system; Service accessibility“ . GSM 03.03 (ETS 300 927): “Digital cellular telecommunications system (Phase 2+); Numbering, addressing and identification“. GSM 03.22 (ETS 300 930): “Digital cellular telecommunications system; Functions related to Mobile Statio
20、n (MS) in idle mode and group receive mode“. GSM 03.38 (ETS 300 900): “Digital . cellular telecommunications system (Phase 27); Alphabets and language-specific information“. GSM 03.40 (ETS 300 901): “Digital cellular telecommunications system (Phase 2+); Technical realization of the Short Message Se
21、rvice (SMS); Point-to-Point (PP)“. GSM 04.08 (ETS 300 940): “Digital cellular telecommunications system (Phase 2+); Mobile radio interface layer 3 specification“. GSM 11.11 (ETS 300 977): “Digital cellular telecommunications system (Phase 2+); Specification of the Subscriber Identity Module - Mobile
22、 Equipment (SIM - ME) interface“. GSM 11.14: “Digital cellular telecommunications system (Phase 2+); Specification of the SIM Application Toolkit for the Subscriber Identity Module - Mobile Equipment (SIM - ME) interface“. Previous page is blank STD-ETSI GSM 02.22-ENGL 1998 m 3400855 0332b57 400 W P
23、age 8 GSM 02.22 Version 5.4.0 Release 1996: July 1998 3 Definitions and abbreviations 3.1 Abbreviations For the purposes of this GTS, the following abbreviations apply: CCK CNL GID1 GID2 EF IMEI IMSI MCC MNC NCK NSCK PCK SIM SMS SP SPCK TMSI Corporate Control Key Co-operative Network List Group Iden
24、tifier (level 1) Group Identifier (level 2) Elementary File International Mobile Equipment Identity International Mobile Subscriber Identity Mobile Country Code Mobile Network Code Network Control Key Network Subset Control Key Perso na kat ion Control Key Subscriber Identity Module Short Message Se
25、rvice Service Provider Service Provider Control Key Temporary Mobile Subscriber Identity Further GSM abbreviations are given in GSM O1 .O4 (ETR 350)1. 3.2 Definitions For the purposes of this GTS, the following definitions apply: corporate personalisation : Allows a corporate customer to personalise
26、 MES that he provides for his employees or customers use so that they can only be used with the companys own SIMs. de-personalisation : Is the process of deactivating the personalisation so that the ME ceases to carry out the verification checks. network personalisation : Allows the network operator
27、 to personalise a ME so that it can only be used with that particular network operators SIMs network subset personalisation: A refinement of network personalisation, which allows network operators to limit the usage of a ME to a subset of SIMs normal mode of operation: Is the mode of operation into
28、which the ME would have gone if it had no personalisation checks to process. personalisation: Is the process of storing information in the ME and activating the procedures which verify this information against the corresponding information stored in the SIM whenever the ME is powered up or a SIM is
29、inserted, in order to limit the SIMs with which the ME will operate. I SIM personalisation: Enables a user to personalise a ME so that it may only be used with particular SIM (s). SP personalisation: Allows the service provider to personalise a ME so that it can only be used with that particular ser
30、vice providers SIMs. user: Normally refers to the person performing the personalisation or de-personalisation operations and may represent a network operator, service provider, manufacturer of the user/owner of the handset, depending on the context. network code: MCC and MNC. network subset code: di
31、gits 6 and 7 of the IMSI. I STD-ETSI GSM 02-22-ENGL Code Network Network SP Corporate SIM (MCC, MNC) Subset (IMSI digits (IMSI digits 8 to 15) 6 and 7) Personalisation category Network J Network subset J J 1998 61 3400855 0332b58 347 SIM Page 9 GSM 02.22 Version 5.4.0 Release 1996: July 1998 SP code
32、: code which when combined with the network code refers to a unique SP. The code is provided in the GIDl file on the SIM (see Annex A.1.) and is correspondingly stored on the ME. Corporate code: code which when combined with the network and SP codes refers to a unique Corporate. The code is provided
33、 in the GID2 file on the SIM (see Annex A.1.) and is correspondingly stored on the ME. SIM code : code which when combined with the network and NS codes refers to a unique SIM. The code is provided by the digits 8 to 15 of the IMSI network code group: same as network code network subset code group:
34、combination of a network subset code and the associated network code. SP code group: combination of the SP code and the associated network code. Corporate code group: combination of the Corporate code and the associated SP and network codes. J J J SIM code group : combination of the SIM code and the
35、 associated network subset and network codes (it is equivalent to the IMSI). Personalisation entity : Network, network subset, SP, Corporate or SIM to which the ME is personalised 4 General description The personalisation features work by storing information in the ME which limits the SIMs with whic
36、h it will operate, and by checking this information against the SIM whenever the ME is powered up or a SIM is inserted. If a check fails, the ME enters the “limited service state“ in which only emergency calls can be attempted (see annex A.2). There are five personalisation categories of varying gra
37、nularity; network, network subset, SP, corporate and SIM. The personalisation categories are independent is so far as each category can be activated or de-activated regardless of the status of the others. Each category has a separate personalisation indicator to show whether it is active or not. The
38、 ME can be personalised to one network, one network subset, one SP, one Corporate, one SIM or any combination thereof. The ME may optionally be personalised to multiple networks, network subsets, SPs, Corporates, SIMs or any combinations thereof. The codes used for each personalisation category are
39、shown in Table 1. Some categories require several codes (e.g. SP and network for SP personalisation) and each combination of codes relating to a particular entity (network, SP etc.) is referred to as a code group. To personalise to multiple entities, multiple code groups are stored in the ME. For ea
40、ch activated personalisation category, the ME retrieves the relevant codes from the SIM and checks the retrieved code group against the (list of) code group) stored in the ME. If a match is found with any of the code groups stored in the ME, the check is passed for that category. If checks for all a
41、ctive categories are passed, then the MS goes into normal operation. Table 1: Codes used by each personalisation category SP I J I J I corporate I J I I J I d I Page 10 GCM 02.22 Version 5.4.0 Release 1996: July 1998 Precautions must be taken to ensure that when more than one personalisation categor
42、y is to be activated or when the ME is to be personalised to more than one entity of a personalisation category, the new codes are not in conflict with any existing valid codes. To avoid such conflicts, checks are carried out by the ME during the personalisation cycle, as described in clause 13. As
43、an optional ME feature, the status (activated or not) of each personalisation category and the values of the relevant codes may be read by the user. 5 Network personalisation 5.1 Network personalisation Network personalisation allows a ME to be personalised to a particular network, for example to pr
44、event the use of stolen MES on other networks. The ME may optionally be personalised to more than one network. The ME is network personalised by storing the code (MCC+MNC) (see GSM 03.03 4) of the relevant network(s) in the ME and setting a network personalisation indicator in the ME to “on“. Whenev
45、er a SIM is inserted, or the MS is powered up with a SIM already in place, the International Mobile Subscriber Identity (IMSI) is read from the SIM and the embedded netw6rk code (MCC+MNC) checked against that stored in the ME. If the values differ, the MS shall go into emergency calls only mode as d
46、efined in annex A.2. The network personalisation feature is controlled by a Network Control Key, (NCK) which has to be entered into the ME in order to network de-personalise it. In order to support the network personalisation feature the ME shall have storage for the network personalisation indicato
47、r, the network code(s) and the NCK. 5.1.1 Operation of network personalised ME The network personalisation check described below is performed whenever a SIM is inserted or the ME is powered up with a SIM already in place. The personalisation check is as follows. When more than one personalisation is
48、 active in the ME, normal mode of operation includes performing any outstanding personalisation checks: a) check the ME is network personalised: The ME checks its network personalisation indicator, if it is set to “off“ the personalisation check shall be stopped and the MS goes into the normal mode
49、of operation, omitting the remaining steps of the check; b) check the network code(s): The ME reads the IMSI from the SIM, extracts the network code from it and checks it against the (list of) value( stored on the ME. If no match is found in b), the ME may display an appropriate message, (e.g., “Incorrect SIM“) and shall go into the emergency calls only mode as defined in annex A.2. If a match is found, the.MS goes into the normal mode of operation. 5.1.2 Network personalisation cycle 5.1.2.1 Personalisation cycle The process of personalisation can only be ca
