1、GSM GSM 08.58TECHNICAL November 1999SPECIFICATION Version 5.10.0Source: SMG Reference: RGTS/SMG-030858QR6ICS: 33.020Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM)GLOBAL SYSTEM FORMOBILE COMMUNICATIONSRDigital cellular telecommunications system (P
2、hase 2+);Base Station Controller - Base Transceiver Station(BSC - BTS) interface;Layer 3 specification(GSM 08.58 version 5.10.0 Release 1996)ETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Luciole
3、s - Sophia Antipolis - Valbonne - FRANCEInternet: secretariatetsi.fr - http:/www.etsi.orgTel.:+33492944200-Fax:+33493654716Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media. Eur
4、opean Telecommunications Standards Institute 1999. All rights reserved.Page 2GSM 08.58 version 5.10.0 Release 1996: November 1999Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concern
5、ing its accuracy, please write to“ETSI Standards Making Support Dept.“ at the address shown on the title page.Page 3GSM 08.58 version 5.10.0 Release 1996: November 1999ContentsIntellectual Property Rights7Foreword7Introduction71 Scope 91.1 Normative references 91.2 Abbreviations .102 Protocol model
6、103 Radio Link Layer Management Procedures 113.1 Link establishment indication.113.2 Link establishment request 123.3 Link release indication .123.4 Link release request.123.5 Transmission of a transparent L3-Message in acknowledged mode 133.6 Reception of a transparent L3-Message in acknowledged mo
7、de133.7 Transmission of a transparent L3-Message in unacknowledged mode 133.8 Reception of a transparent L3-Message in unacknowledged mode133.9 Link error indication134 Dedicated channel management procedures .144.1 Channel activation144.1.1 Signalling Procedure .144.1.2 Activation for Intra-Cell Ch
8、annel Change 154.1.3 Activation for Asynchronous Handover .154.1.4 Activation for Synchronous Handover .154.1.5 Activation for Secondary Channels in Multislot Configuration.164.1.6 Channel reactivation164.2 Channel MODE MODIFY.164.3 Handover detection174.4 Start of encryption174.5 Measurement report
9、ing184.5.1 Basic measurement reporting .184.5.2 Measurement pre-processing194.5.2.1 Pre-processing configuration.194.5.2.2 Pre-processed measurement reporting.194.5.3 Extended measurement reporting $(MAFA)$ .204.6 Deactivate SACCH 204.7 Radio channel release .214.8 MS power control .214.9 Transmissi
10、on power control.214.10 Connection failure 224.11 Physical context request 224.12 SACCH information modify224.13 Talker detection .234.14 Listener detection.235 Common channel management procedures.235.1 Channel request by MS235.2 Paging235.3 Delete indication.245.4 CCCH load indication.245.5 Broadc
11、ast information modify 245.6 Short Message Cell Broadcast 24Page 4GSM 08.58 version 5.10.0 Release 1996: November 19995.7 IMMEDIATE ASSIGNMENT 275.8 Notification. 276 TRX management procedures . 276.1 Radio resource indication 276.2 SACCH filling information modify 286.3 Flow control . 286.4 Error r
12、eporting . 297 Error handling . 297.1 General 297.2 Message discriminator error 297.3 Message type error . 297.4 Message sequence error. 307.5 General information element errors 307.6 Mandatory information element errors 307.7 Optional information element errors 307.8 Conditional information element
13、 errors . 308 Message formats and contents 308.1 Transparent messages . 318.2 Non-transparent messages (BSC-BTS specific messages) . 328.3 Radio link layer management messages 328.3.1 DATA REQUEST 328.3.2 DATA INDICATION 328.3.3 ERROR INDICATION. 338.3.4 ESTABLISH REQUEST 338.3.5 ESTABLISH CONFIRM 3
14、38.3.6 ESTABLISH INDICATION 338.3.7 RELEASE REQUEST. 348.3.8 RELEASE CONFIRM 348.3.9 RELEASE INDICATION . 348.3.10 UNIT DATA REQUEST 358.3.11 UNIT DATA INDICATION. 358.4 DEDICATED CHANNEL MANAGEMENT MESSAGES . 358.4.1 CHANNEL ACTIVATION 368.4.2 CHANNEL ACTIVATION ACKNOWLEDGE 378.4.3 CHANNEL ACTIVATI
15、ON NEGATIVE ACKNOWLEDGE . 378.4.4 CONNECTION FAILURE INDICATION . 378.4.5 DEACTIVATE SACCH 388.4.6 ENCRYPTION COMMAND 388.4.7 HANDOVER DETECTION 388.4.8 MEASUREMENT RESULT. 398.4.9 MODE MODIFY 398.4.10 MODE MODIFY ACKNOWLEDGE 408.4.11 MODE MODIFY NEGATIVE ACKNOWLEDGE . 408.4.12 PHYSICAL CONTEXT REQU
16、EST . 408.4.13 PHYSICAL CONTEXT CONFIRM 408.4.14 RF CHANNEL RELEASE . 418.4.15 MS POWER CONTROL. 418.4.16 BS POWER CONTROL 418.4.17 PREPROCESS CONFIGURE 428.4.18 PREPROCESSED MEASUREMENT RESULT 428.4.19 RF CHANNEL RELEASE ACKNOWLEDGE 428.4.20 SACCH INFO MODIFY. 428.4.21 TALKER DETECTION 438.4.22 LIS
17、TENER DETECTION 438.5 COMMON CHANNEL MANAGEMENT MESSAGES . 438.5.1 BCCH INFORMATION . 448.5.2 CCCH LOAD INDICATION. 448.5.3 CHANNEL REQUIRED. 458.5.4 DELETE INDICATION 458.5.5 PAGING COMMAND 46Page 5GSM 08.58 version 5.10.0 Release 1996: November 19998.5.6 IMMEDIATE ASSIGN COMMAND468.5.7 SMS BROADCA
18、ST REQUEST.468.5.8 SMS BROADCAST COMMAND .478.5.9 CBCH LOAD INDICATION478.5.10 NOTIFICATION COMMAND.488.6 TRX MANAGEMENT MESSAGES488.6.1 RF RESOURCE INDICATION 488.6.2 SACCH FILLING .498.6.3 OVERLOAD.498.6.4 ERROR REPORT .509 Information element codings .519.1 Message discriminator.519.2 MESSAGE TYP
19、E.519.3 Other information elements .539.3.1 Channel Number .549.3.2 Link Identifier .549.3.3 Activation Type 559.3.4 BS Power.559.3.5 Channel Identification569.3.6 Channel Mode .569.3.7 Encryption information.589.3.8 Frame Number 589.3.9 Handover reference.599.3.10 L1 Information .599.3.11 L3 Inform
20、ation (message name) .599.3.12 MS Identity.609.3.13 MS Power609.3.14 Paging Group 609.3.15 Paging Load 609.3.16 Physical Context619.3.17 Access Delay.619.3.18 RACH Load .619.3.19 Request Reference .629.3.20 Release Mode .629.3.21 Resource Information639.3.22 RLM Cause639.3.23 Starting Time .649.3.24
21、 Timing Advance.649.3.25 Uplink Measurements649.3.26 Cause 659.3.27 Measurement result number .689.3.28 Message Identifier .689.3.29 SACCH Information.689.3.30 System Info Type.699.3.31 MS Power Parameters 709.3.32 BS Power Parameters.709.3.33 Pre-processing Parameters.709.3.34 Pre-processed Measure
22、ments 719.3.35 Full Immediate Assign Info719.3.36 SMSCB Information.719.3.37 MS Timing Offset.719.3.38 Erroneous Message 729.3.39 Full BCCH Information (message name) 729.3.40 Channel Needed729.3.41 CB Command type 739.3.42 SMSCB Message 749.3.43 CBCH Load Information 749.3.44 SMSCB Channel Indicato
23、r.749.3.45 Group call reference749.3.46 Channel description.759.3.47 NCH DRX information .759.3.48 Command indicator .75Page 6GSM 08.58 version 5.10.0 Release 1996: November 19999.3.49 eMLPP Priority 769.3.50 UIC 769.3.51 Main channel reference 76Annex A (informative): Document change history 77Hist
24、ory. 78Page 7GSM 08.58 version 5.10.0 Release 1996: November 1999Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. Theinformation pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-membe
25、rs, and can be found in SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentiallyEssential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSISecretariat. Latest updates are available on the ETSI Web server (http:/www.etsi.org/ipr).Pursuant to the
26、 ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI.No guarantee can be given as to the existence of other IPRs not referenced in SR 000 314 (or theupdates on the ETSI Web server) which are, or may be, or may become, essential to the presentdocument.ForewordThis
27、Global System for Mobile communications Technical Specification (GTS) has been produced by theSpecial Mobile Group (SMG) Technical Committee (TC) of the European Telecommunications StandardsInstitute (ETSI).This GTS specifies the general structure of layer 3 and traffic management procedures and mes
28、sagesused on the A-bis interface to support signalling procedures within the digital cellular telecommunicationssystem.The contents of this GTS are subject to continuing work within SMG and may change following formalSMG approval. Should SMG modify the contents of this GTS it will then be republishe
29、d by ETSI with anidentifying change of release date and an increase in version number as follows:Version 5.x.ywhere:5 indicates GSM Phase 2+ Release 1996;x the second digit is incremented for all other types of changes, i.e. technical enhancements,corrections, updates, etc.y the third digit is incre
30、mented when editorial only changes have been incorporated in thespecification.IntroductionThe present document includes references to features which are not part of the Phase 2+ Release 96 ofthe GSM Technical specifications. All subclauses which were changed as a result of these featurescontain a ma
31、rker (see table below).The following table lists all features that were introduced after Release 96.Feature DesignatorMobile Assisted Frequency Allocation $(MAFA)$Page 8GSM 08.58 version 5.10.0 Release 1996: November 1999Blank pagePage 9GSM 08.58 version 5.10.0 Release 1996: November 19991 ScopeThe
32、use and general aspects of the Base Station Controller (BSC) to Base Station Transceiver (BTS)interface (the A-bis interface) are given in GSM 08.51.This Global System for Mobile communications Technical Specification (GTS) specifies the generalstructure of layer 3 and traffic management procedures
33、and messages used on the A-bis interface tosupport signalling procedures as defined in GSM 04.08.Network management procedures and messages for the A-bis interface are defined in GSM 08.59.The functional split between BSC and BTS is defined in GSM 08.52. The procedures and messagesrequired to suppor
34、t this split are defined in detail in this GTS.1.1 Normative referencesThis GTS incorporates by dated and undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, s
35、ubsequent amendments to or revisions of any of these publicationsapply to this GTS only when incorporated in it by amendment or revision. For undated references, thelatest edition of the publication referred to applies.1 GSM 01.04 (ETR 350): “Digital cellular telecommunications system (Phase 2+);Abb
36、reviations and acronyms“.2 GSM 03.20 (ETS 300 929): “Digital cellular telecommunications system(Phase 2+); Security related network functions“.3 GSM 04.04 (ETS 300 936): “Digital cellular telecommunications system;Layer 1; General requirements“.4 GSM 04.05 (ETS 300 937): “Digital cellular telecommun
37、ications system; DataLink (DL) layer; General aspects“.5 GSM 04.06 (ETS 300 938): “Digital cellular telecommunications system(Phase 2+); Mobile Station - Base Station System (MS - BSS) interface; DataLink (DL) layer specification“.6 GSM 04.08 (ETS 300 940): “Digital cellular telecommunications syste
38、m(Phase 2+); Mobile radio interface layer 3 specification“.7 GSM 04.12 (ETS 300 943): “Digital cellular telecommunications system(Phase 2+); Short Message Service Cell Broadcast (SMSCB) support on themobile radio interface“.8 GSM 05.02 (ETS 300 908): “Digital cellular telecommunications system(Phase
39、 2+); Multiplexing and multiple access on the radio path“.9 GSM 05.05 (ETS 300 910): “Digital cellular telecommunications system(Phase 2+); Radio transmission and reception“.10 GSM 05.08 (ETS 300 911): “Digital cellular telecommunications system(Phase 2+); Radio subsystem link control“.11 GSM 05.10
40、(ETS 300 912): “Digital cellular telecommunications system(Phase 2+); Radio subsystem synchronization“.12 GSM 08.06: “Digital cellular telecommunications system (Phase 2+); Signallingtransport mechanism specification for the Base Station System -Mobile-services Switching Centre (BSS - MSC) interface
41、“.Page 10GSM 08.58 version 5.10.0 Release 1996: November 199913 GSM 08.08: “Digital cellular telecommunications system (Phase 2+);Mobile-services Switching Centre - Base Station System (MSC - BSS) interface;Layer 3 specification“.14 GSM 08.51: “Digital cellular telecommunications system; Base Statio
42、n Controller- Base Transceiver Station (BSC - BTS) interface; General aspects“.15 GSM 08.52: “Digital cellular telecommunications system; Base Station Controller- Base Transceiver Station (BSC - BTS) interface; Interface principles“.16 GSM 08.56: “Digital cellular telecommunications system; Base Sta
43、tion Controller- Base Transceiver Station (BSC - BTS) interface; Layer 2 specification“.1.2 AbbreviationsAbbreviations used in this GTS are listed in GSM 01.042 Protocol modelA model for L3 can be found in figure 2.1.L2 addressing is made to TRX (or BCF) using the TEI of LAPD. Different L2 links are
44、 used for trafficmanagement messages (RSL, Radio Signalling Link), network management messages (OML, Operation- a link layer failure, i.e. the repetition of an I-frame N200 times without an acknowledgement;- the repetition of an SABM or DISC frame N200 times without an acknowledgement;- the receptio
45、n of an SABM frame in multi-frame established state.When such an event has occurred, BTS notifies BSC by sending an ERROR INDication messagecontaining the relevant cause information.Page 14GSM 08.58 version 5.10.0 Release 1996: November 1999MS BTS BSCabnormalcase ERROR IND 4 Dedicated channel manage
46、ment procedures4.1 Channel activationThis procedure is used to activate a channel at the BTS for an MS which later will be commanded to thischannel by an IMMediate ASSIGN, an ASSIGN CoMmanD, an ADDitional ASSIGNment; aNOTIFICATION, a CHANNEL RELEASE (with a Channel description) a HANDOver CoMmanD or
47、 aCONFiguration CHange CoMmanD message.In the handover case, the procedure is used between the target BSC and the target BTS to activate achannel for a subsequent handover from the old BTS.4.1.1 Signalling ProcedureBSC determines what channel shall be used and starts up that channel at BTS by sendin
48、g a CHANnelACTIVation message to the relevant TRX. This message contains the reason for the activation(immediate assignment, assignment, asynchronous/synchronous handover, additional assignment,activation of a secondary channel in a multislot configuration), the identification of the channel to be u
49、sed(channel no) and a complete description of the channel (full/half rate, speech/data, coding/rate adaption,hopping sequence, encryption key etc.).If the Encryption Information field is present, the activation is done with ciphering active. If the EncryptionInformation element is not present, activation is done without ciphering.After activating the channel as requested, TRX responds with the CHANnel ACTIVation ACKnowledgemessage. This message contains the current frame number at BTS. The frame number is used by BSC todetermine the
