ETSI I-ETS 300 783-1998 Transmission and Multiplexing (TM) Passive Optical Components Fibre Optic Fusion Splices for Single-Mode Optical Fibre Transmission Systems Common Requireme_1.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN 61191-4-2017 en Printed board assemblies - Part 4 Sectional specification - Requirements for terminal soldered assemblies.pdf

EN 61191-6-2010 en Printed board assemblies - Part 6 Evaluation criteria for voids in soldered joints of BGA and LGA and measurement method《印刷电路板组件 第6部分 球栅阵列和网格阵列的焊接接头内空隙及测量方法用评定标准.pdf

EN 61192-1-2003 en Workmanship requirements for soldered electronic assemblies Part 1 General《钎焊电子组件的工艺要求 第1部分 总则 IEC 61192-1 2003》.pdf

EN 61192-2-2003 en Workmanship requirements for soldered electronic assemblies Part 2 Surface-mount assemblies《钎焊电子组件的工艺要求 第2部分 表面安装组件 IEC 61192 2003》.pdf

EN 61192-3-2003 en Workmanship requirements for soldered electronic assemblies Part 3 Through-hole mount assemblies《钎焊电子组件的工艺要求 第3部分 穿孔安装组件 IEC 61192-3 2002》.pdf

EN 61192-4-2003 en Workmanship requirements for soldered electronic assemblies Part 4 Terminal assemblies《钎焊电子组件的工艺要求 第4部分 终端组件 IEC 61192-4 2002》.pdf

EN 61192-5-2007 en Workmanship requirements for soldered electronic assemblies - Part 5 Rework modification and repair of soldered electronic assemblies《钎焊电子组件的工艺要求 第5部分 钎焊电子组件的再加工.pdf

EN 61193-1-2002 en Quality Assessment Systems - Part 1 Registration and Analysis of Defects on Printed Board Assemblies《质量评定体系 第1部分 印制板装配件的缺陷注册和分析 IEC 61193-1 2001》.pdf

EN 61193-2-2007 en Quality assessment systems - Part 2 Selection and use of sampling plans for inspection of electronic components and packages《质量评定体系 第2部分 电子元器件和封装抽样计划的选择和使用》.pdf