1、* ETSI PRI-ETS*300 020-3 96 H 340QB55 OLL3209 307 kFEAN TELECOMMUNICATION STANDARD DRAF pr I=ETS 300 020-3 June 1996 Second Edition Source: ETSI TC-SMG - Reference: RI/SMG-071110 ICs: 33.060.50 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) GLOBA
2、L SYSTEM FOR MOBILE COMMUNICATIONS Digital cellular telecommunications system (Phase 1); Mobile station conformance test system Part 3: DCS 1 800 mobile station conformity specification (GSM 11 .I O-DCS) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 So
3、phia Antipolis CEDEX - FRANCE Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretarat - Internet: secretariat Qetsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized
4、by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 1996. All rights resewed. ETSI PRI-ETS*300 020-3 96 W 3400855 OLL3210 O29 W Page Oa GSM 11 .I O-DCS Version 3.1 4.O(Draft prl-ETS 300 020-3: June
5、1996) Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. ETSI
6、PRI-ETS*300 020-3 9b m 3400855 0133233 Tb5 m Page Ob GSM 11.1 O-DCS Version 3.14.0 (Draft prl-ETS 300 020-3: June 1996) Foreword This draft Interim European Telecommunication Standard (I-ETS) has been produced by the Special Mobile Group (SMG) Technical Committee of the European Telecommunications S
7、tandards Institute (ETSI) and is submitted for the Unified Approval Procedure (UAP) of the ETSI standards approval procedure. This draft prl-ETS 300 020-3 second edition has been produced as a result of further updating work carried out by TC-SMG on the base document GSM 11.1 O-DCS. This LETS 300 02
8、0-3, corresponds to ETSI Technical Specification GSM 11 .lO-DCS version 3.14.0. This part of the LETS (Part 3), contains conformity specifications for which DCS 1800 mobile stations, within the European digital cellular telecommunications system (Phase i), are tested for compliance. This I-ETS descr
9、ibes the test procedures, test conditions and test site and the provisions within the DCS 1800 mobile station, to support the process of conformance testing. I-ETC 300 020 consists of the following three parts: I-ETS 300 020-1 I-ETS 300 020-2 I-ETS 300 020-3 NOTE: European digital cellular telecommu
10、nications system (phase 1) Mobile station conformance test system System simulator specification (Part 1) Reference: GSM 11 .lo. European digital cellular telecommunications system (phase 1) Mobile station conformance test system System simulator specification (Part 2) Reference: GSM 11.40. Digital
11、cellular telecommunications system (phase 1) Mobile station conformance test system System simulator specification Part 3: DCS 1800 mobile station conformity specification Reference: GSM 11 .1 O-DCS. TC-SMG has produced documents which give the technical specifications for the implementation of the
12、European digital cellular telecommunications system. Historically, these documents have been identified as GSM Technical Specifications (GSM-TSs). These GSM-TSs may have subsequently become I-ETSs (Phase I), or ETSc (Phase 2), whilst others may become ETSI Technical Reports (ETRs). GSM-TSs are, for
13、editorial reasons, still referred to in current GSM documents. lhe specification from which this I-ETS has been derived was originally based on CEPT documentation, hence the presentation of this I-ETS is not in accordance with the ETSVPNE rules. The page numbering of the main part of this I-ETS is a
14、ligned with GSM-TS 11.10 version 3.14.0. This LETS contains 245 pages in total. ETSI PRI-ETS*300 020-3 96 3400855 01132L2 9T3I Page Oc GSM 11.10-DCS Version 3.14.0 (Draft prl-ETS 300 020-3: June 1996) Blank page ETSI PRI-ETS*300 020-3 76 3400855 OLL3213 838 Page Od GSM 11.10-DCS Version 3.14.0 (Draf
15、t prl-ETS 300 020-3: June 1996) ETSVTC SMG Updated by: ETSI/PT12/48V Date: May 1996 ETSI TECHNICAL SPECIFICATION GSM 11.10-DCS DCS 1800 Mobile Station Conformity Specification Version 3.1 4.0 Table of Contents Note: GSM 11 .l O-DCS consists of GSM 11.1 O V3.19.0 with the following parts replaced by
16、those contained in this specification. Note: Complete parts are included. Section Title Part I Part 11.2 Part 11.3 Part 11.4 Part 11.5.3.1 Part 11.5.3.3 Part 11.5.3.6 Part 11.5.3.7 Part 11.5.3.9 Part 11.6 Pari 11.8 Part 11.17 Annex 1 Annex 2 %ope The Transceiver Transmitter Receiver Default conditio
17、ns and structured sequence of test Test of MS Functions in Idle Mode Elementary Procedures for RR Management Elementary procedures of Mobility management Testing of structured procedures Link Management Test of SIWE Interface Test of low battery voltage detection Reference test methods Measurement U
18、ncertainty Version Number of pages 3.12.1 13 3.12.1 7 3.12.1 18 3.12.1 21 3.12.1 3 3.12.1 3 3.12.1 47 3.12.1 32 3.12.1 12 3.12.1 25 3.12.1 33 3.12.1 1 3.1 2.1 7 3.12.1 5 ETSI PRI-ETS*300 020-3 96 m 3400855 0113214 774 Page 2 GSM 11.1 O-DCS Version 3.1 4.0, Contents (Draft prl-ETS 300 020-3: June 199
19、6) O. Introduction 1. GENERAL 1 .l. . Scope 1.2 . Introduction 1.2.1 . Relation with other GSM recommendations 1.2.2 Terminology on Mobile Station configurations 1 -2.3 _.App licability of these specifications 1.2.3.1 Application to terminal equipment 1.2.4 The System Simulator 1.3 . Definitions 1.4
20、 . TERMINOLOGY 1.4.1 Abbreviations and Acronyms 1.4.2 Conventions for mathematical notations 1.4.3 .,.Conventions on electrical terms 1.4.4 . Terms on test conditions 1.5 . List of the GSM delta recommendations, on which these test specifications are based I Aspect I: FORMAL PROCEDURES AND GENERAL R
21、EQUIREMENTS 1.2 . Testing and Approval Methodology in general (Ll, L2, L3) 1.2.1 Testing of optional functions and procedures 1.2.2 .-.Access 1.2.3 . Diffe rent layers 1.2.4 . Information to be provided by the Apparatus Supplier 1.3 . Applicability of the individual chapters 1.4 General requirements
22、 concerning safety of people and . rotection of the network and terminal. 1.4.1 Interference to car management systems. 1.4.2 . Requirements concerning environmental conditions for operation 11.2 ,.The transceiver 11.2.1 . Radio frequency aspects 11.2.1.1 . Frequency bands 11.2.1.2 . RF Channels and
23、 channel numbering 11.2.1.3 Frequency hopping 11.2.2 ,.Spurious emissions 11.2.2.1 Definition 11.2.2.2 Method of Measurement (a) 11.2.2.2.1 . Mobile Allocated Channel 11.2.2.2.2 MS in Idle Mode 11.2.2.3 Method of Measurement (b) 11.2.2.3.1 . MS Allocated a Channel 11.2.2.3.2 MS in Idle Mode 11.2.2.4
24、 Requirements 11.3 .TRANSMlTTER 11.3.1 Phase Error and Frequency Error 11.3.1.1 .Method of Measurement 11.3.1.2 Limits 11.3.1.2.1 . Frequency Error 11.3.1.2.2 Phase Error 11.3.2 . Frequency Error under Multipath - a transportable station; - a handheld station; - a vehicle mountedhranspottable statio
25、n; - a vehicle mountedhandheld station. These specifications cover the minimum characteristics considered necessary in order to provide sufficient equipment performance for mobile station equipment in the WDCS 1800 system and to prevent interference to other services or to other users, and to GSM an
26、d DCS 1800 PLMNs. Where the 900 MHz service is referred to in sections of GSM 11.10 not included in this document then this shall be considered as the 1800 MHz service. They do not necessarily include all the characteristics which may be required by a user, nor do they necessarily represent the opti
27、mum performance achievable. They apply to the public land mobile radio telephone service in the WDCS 1800 system, using constant envelope modulation and operating on radio frequencies in the 8881800 MHz band with a channel separation of 200 kHz and carrying 8 full rate traffic channels or 16 half ra
28、te channels per carrier according to the TDMA principle. I ETSI PRI-ETS*IOO 020-3 96 m 3400855 033322b 476 m Page 2 GSM 11.1 O-DCS Part I (scope) (Draft prl-ETS 300 020-3: June 1996) Mobile Termination 1.2 Introduction Interface: S, R, etc Terminal Equipment 1.2.1 Relation with other GSM recommendat
29、ions This specification is pari of the GSM-series of recommendations. This specification neither replaces any of the other GSM recommendations , nor is it created to provide full understanding of (parts of) the GSMDCS 1800 system. This specification lists the requirements, and provides the methods o
30、f testing for use by test houses when testing a GSMDCS 1800 mobile station for conformance. For a full description of the GSMDCS 1800 system, please refer to all the GSM recommendations plus the set of delta recommendation! . A complete list of the W recommendations, on which these conformance test
31、specifications are based, is listed in GSM 11.1 0.A list of the recommendations amended for DCS 1800 is aiven in DaraaraDh 1.5. If it is judged that there is a difference of interpretation between these conformance test specifications, and any other GSM recommendation, then the other GSM recommendat
32、ion shall prevail. 1.2.2 Terminology on Mobile Station configurations . Mobile Station is the complete eaubment configuration Apart in a- communication. However, this might not “0“ station as it is offered to a test house for conformance testing. Whilst the definition above includes terminal equipme
33、nt which is connected to the “mobile termination“, such terminal equipmentuE) is in general submitted to a separate type approval procedure, on the basis of Rec. TTTE-04-08 . In general, the GSM DCS1800 Mobile Station, as it will be presented to a test house for conformance I testing, is the station
34、 without all the additional terminal equipment. Such a piece of hardware is also called a Mobile Termination (MT), but in this specification, the expression Mobile Station (MS) is used for any form of the hardware as it is offered to the test house. During the tests, the interfaces of the MT will be
35、 connected to a “System Simulator“ (SS), which will also emulate the TE. For some tests, it may be necessary to estabilish a pre-configured setup of the MS. As an example: for reception of automatic fax group 3 to a fax machine on the R-interface, the MS needs configuration information about the pre
36、sence of such a machine on that interface. As an alternative, the terminal equipment may be physically integrated. For a more detailed description of MSconfigurations, see GSM 02.06-DCS ETSI pRI-ETSr30 020-3 qb 3400855 0113227 322 = Page 3 GSM 11.10-DCS Version 3.14.0, Part I (scope) (Draft prl-ETS
37、300 020-3: June 1996) 1.2.3 Applicability of these specifications These specifications apply to the unit which includes the hardware to establish a connection accross the radio interface. If a Mobile Station is equipped with a connector, to connect terminal equipment on an S or R intedace, then test
38、ing of the Mobile Station will include testing of appropriate functioning to and from this connector. These specifications do not apply to terminal equipment which is to be connected to that connector (which constitutes a public interface), even if it is delivered with the MS. These specifications d
39、o not apply to a MS where the user-interface offers 2-wire or 4-wire PSTN type connection. 1.2.3.1 Application to terminal equipment If an MS is delivered for conformance testing, and it contains physically integrated terminal equipment, then this specification applies to the complete Mobile Station
40、 including that terminal equipment. These specifications also apply to separate terminal equipmentm, Wis delivered for conformance testing with the Mobile Station, 3 . The MS is then tested as an MTO. In that case, the specific terminal equipment with which the Mobile Station is tested is documented
41、 in the test report. I 1.2.4 lhe System Simulator In order to bring the MS into operation, it should be necessary to provide the MS with some signals, and the MSs output signals should be analysed. Rather than describing the hardware configuration of the measuring arrangement (and the requirements t
42、o it) in each individual test, the part thereof which is contained in the System Simulator (SS) is described in a separate document, Recommendation GSM 11 -4O-DCS. .The use of such a SS is assumed throuahout GSM 11 .lo-DCS. 1.3 Definitions Only a limited set of definitions, with special relevance to
43、 the MS and to conformance testing are included. For a more complete set of expressions see rec. GSM O1 .O4 GSM DCS1800 Mobile Station (GSM DCSl800 MS) ref: MM GSM 02.06-DCS Equipment intended to access a set of GSM DCS1800 PLMN telecommunication services. Services may be accessed while the equipmen
44、t capable of surface movement within the GSM DCS1800 system area is in motion or during halts at unspecified points. Mobile termination The pari of the Mobile Station which terminates the radio transmission to and from the network and adapts terminal equipment (TE) capabilities to those of this radi
45、o transmission. Page 4 ETSI PRI-ETS*300 020-3 9b 3400855 0113228 269 GSM 11 .l-DCS Part I (scope) (Draft prl-ETS 300 020-3: June 1996) Conformity specification ref TG 01-01 A document giving a precise and full description of the technical characteristics of the relevant telecommunications terminal e
46、quipment (such as safety, technical parameters, functions and procedures and service requirements) together with a precise definition of the tests and test methods enabling the conformity of the equipment with the prescribed technical characteristics to be verified. Telecommunications terminal equip
47、ment ref: TG O1 -01 Equipment directly or indirectly connected to public telecommunications networks or for use with public telecommunications services. 1.4 TERMINOLOGY 1.4.1 Abbreviations and Acronyms Abbreviation Full Term Reference GSM AB Access Burst AC ACCH Associated Control Channel AGCH Acces
48、s Grant CHannel ARFCN ARQ Automatic Request for Retransmission AlT (flag) Attach BA BCCH Allocation BCC BS Colour Code BCCH Broadcast Control Channel BCCH-FREQ-NCELL BER Bit Error Ratio BFI Bad Frame Indication Bm full rate traffic channel BN Bit Number BS-AG-BLKS-RES Number of blocks on each common
49、 control channel reserved for access grant messages BS-BCCH-SDCCH-COMB Logical variable that indicates the combination of dedicated and associated control channels on the same physical channel BS-PA-MFR-MS Number of multiframes between two transmissions of the same paging message to MSs of the same paging group Access Class (CO to C15) Absolute Radio Frequency Channel Number Frequency of the RF carrier on which the BCCH of a ne hbouring cell is transmitted BCD Binary Coded 1 ecimal 05.02 02.1 1 05.02 05.08 03.03 05.02 05.08 05.05 05.05 05.02 05.02 05.02 05.02 cc Ca
