1、 ETSI TR 103 313 V1.1.1 (2017-03) System Reference document (SRdoc); Technical characteristics for SRD equipment using Ultra Wide Band Sensor technology (UWB); Medical, wellness and assisted living applications TECHNICAL REPORT ETSI ETSI TR 103 313 V1.1.1 (2017-03) 2 Reference DTR/ERM-554 Keywords h
2、ealth, SRDoc, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be d
3、ownloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any exi
4、sting or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be su
5、bject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org
6、/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without
7、the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Member
8、s. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TR 103 313 V1.1.1 (2017-03) 3 Contents Intellectual Property Rights 5g3Foreword . 5
9、g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions and abbreviations . 8g33.1 Definitions 8g33.2 Abbreviations . 8g34 Comments on the System Reference document . 9g35 Presentation of systems or technologie
10、s . 9g35.1 Background information . 9g35.2 Applications descriptions . 9g35.2.1 Introduction. 9g35.2.2 Wireless Video Transmission in Operating rooms . 11g35.2.2.1 Introduction . 11g35.2.2.2 System requirements . 12g35.2.2.3 Technical description 12g35.2.2.4 Mitigation factors 13g35.2.3 UWB based ca
11、rdio-pulmonary sensor for animals . 13g35.2.3.1 Introduction . 13g35.2.3.2 System requirements . 14g35.2.3.3 Technical description 14g35.2.3.4 Mitigation factors 16g35.2.4 UWB health monitoring application . 16g35.2.4.1 Introduction . 16g35.2.4.2 System requirements . 17g35.2.4.3 Technical descripti
12、on 17g35.2.4.4 Mitigation factors 17g35.2.5 UWB based on-body medical radar 18g35.2.5.1 Introduction . 18g35.2.5.2 System requirements . 19g35.2.5.3 Technical description 19g35.2.5.4 Mitigation factors 19g35.2.6 UWB based remote respiration and heart rate monitor . 20g35.2.6.1 Introduction . 20g35.2
13、.6.2 System requirements . 20g35.2.6.3 Technical description 21g35.2.6.4 Mitigation factors 21g35.3 Classification of medical sensor UWB applications 22g35.3.1 General 22g35.3.2 Non imaging applications (or mode-B echography) . 22g35.3.2.1 Cardiology and vascular 22g35.3.2.2 Pulmonary . 22g35.3.2.3
14、Ear-Nose-Throat medicine 22g35.3.2.4 Gastroenterology . 22g35.3.2.5 Midwifery 22g35.3.3 Imaging applications . 22g35.3.3.1 Introduction . 22g35.3.3.2 Trauma and cerebral vascular care 22g35.3.3.3 Oncology . 23g3ETSI ETSI TR 103 313 V1.1.1 (2017-03) 4 5.3.3.4 UWB radar scanner . 23g36 Current regulat
15、ions . 23g36.1 Overview 23g36.2 Generic regulation 23g36.3 Material sensing devices 24g36.4 Building material analyses applications (BMA) . 25g37 Proposed changes to regulation 25g38 Main conclusions 30g38.1 Business importance . 30g3Annex A: Market information 31g3A.1 Range of applications . 31g3A.
16、2 Market size and value . 31g3A.2.1 Introduction 31g3A.2.2 Market potential Medical communication devices based on UWB 31g3A.2.3 Market potential UWB based animal sensor device . 32g3Annex B: Technical information 33g3Annex C: Expected compatibility issues 34g3C.1 Existing Coexistence studies 34g3An
17、nex D: Bibliography 35g3History 36g3ETSI ETSI TR 103 313 V1.1.1 (2017-03) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members
18、and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org
19、/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the pre
20、sent document. Foreword This Technical Report (TR) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). Modal verbs terminology In the present document “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be
21、 interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document includes necessary information to support the co-opera
22、tion under the MoU between ETSI and the Electronic Communications Committee (ECC) of the European Conference of Post and Telecommunications Administrations (CEPT). Ultra Wide Band technologies enable a very broad new set of applications in the field of medical, assisted living, eHealth and wellness.
23、 The deployment of UWB in the field can be split into the following applications: Communication applications. Sensor and imaging applications. Hybrid application as a combination of sensor and communications. The broad range of potential applications of the technology will be covered in this TR in o
24、rder to classify the requirements and to identify the potential need of specific regulatory activities on CEPT and standardization activities in ETSI. The present document has been created by TC ERM TGUWB. ETSI ETSI TR 103 313 V1.1.1 (2017-03) 6 1 Scope The present document provides information on t
25、he intended applications, the technical parameters, the relation to the existing spectrum regulation and additional new radio spectrum requirements for UWB equipment for the operation in medical, wellness and assisted living environments and applications in the band below 10 GHz. The applications ca
26、n be divided in 3 different categories of medical applications: Category A: Communication Devices in controlled medical environments. Category B: Contact based sensing and imaging devices. Category C: Off-body/off-material sensing and imaging devices. The application environments of the presented te
27、chnologies will cover home environments for assisted living applications, hospital environments including doctors surgeries and automotive environments. The present document includes necessary information to support the co-operation between ETSI and the Electronic Communications Committee (ECC) of t
28、he European Conference of Post and Telecommunications Administrations (CEPT), including: Detailed market information (annex A). Technical information (annex B). Relation to existing spectrum regulation (annex C). 2 References 2.1 Normative references Normative references are not applicable in the pr
29、esent document. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (
30、including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with
31、regard to a particular subject area. i.1 ETSI EN 303 883 (V1.1.1) (02-2016): “Short Range Devices (SRD) using Ultra Wide Band (UWB); Measurement Techniques“. i.2 ETSI EN 302 065-1 (V2.1.1) (11-2016): “Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the
32、essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Requirements for Generic UWB applications“. i.3 ETSI EN 302 065-2 (V2.1.1) (11-2016): “Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 o
33、f the Directive 2014/53/EU; Part 2: Requirements for UWB location tracking“. i.4 ETSI EN 302 065-3 (V2.1.1) (11-2016): “Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 3: Requir
34、ements for UWB devices for ground based vehicular applications“. ETSI ETSI TR 103 313 V1.1.1 (2017-03) 7 i.5 ETSI EN 302 065-4 (V1.1.1) (11-2016): “Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonised Standard covering the essential requirements of article 3.2 of the Directiv
35、e 2014/53/EU; Part 4: Material Sensing devices using UWB technology below 10,6 GHz“. i.6 CEPT ECC/DEC/(06)04 of 24 March 2006 amended 9 December 2011: “The harmonised conditions for devices using Ultra-Wideband (UWB) technology in bands below 10.6 GHz“. i.7 Commission Decision 2007/131/EC of 21 Febr
36、uary 2007 on allowing the use of the radio spectrum for equipment using ultra-wideband technology in a harmonised manner in the Community (notified under document number C(2007) 522). i.8 Commission Decision 2009/343/EC of 21 April 2009 amending Decision 2007/131/EC on allowing the use of the radio
37、spectrum for equipment using ultra-wideband technology in a harmonised manner in the Community (notified under document number C(2009) 2787). i.9 Commission Decision 2014/702/EU of 7 October 2014 amending Decision 2007/131/EC on allowing the use of the radio spectrum for equipment using ultra-wideba
38、nd technology in a harmonised manner in the Community (notified under document C(2014) 7083). i.10 ECC/DEC/(07)01: “ECC Decision of 30 March 2007 on specific Material Sensing devices using Ultra-Wideband (UWB) technology (amended 26 June 2009)“. i.11 ECC Report 120 (March 2008): “ECC Report on Techn
39、ical requirements for UWB DAA (Detect and avoid) devices to ensure the protection of radiolocation in the bands 3.1-3.4 GHz and 8.5-9 GHz and BWA terminals in the band 3.4-4.2 GHz“. i.12 CEPT Report 45: “Report from CEPT to the European Commission in response to the Fifth Mandate to CEPT on ultra-wi
40、deband technology to clarify the technical parameters in view of a potential update of Commission Decision 2007/131/EC“; Report approved on 21 June 2013 by the ECC. i.13 CEPT/ECC Report 64: “The protection requirements of radio communications systems below 10,6 GHz from generic UWB applications“, He
41、lsinki, February 2005. i.14 CEPT Report 34: “Report B from CEPT to European Commission in response to the Mandate 4 on Ultra-Wideband (UWB); Final Report on 30 October 2009 by the Electronic Communications Committee (ECC) within the European Conference of Postal and Telecommunications Administration
42、s (CEPT)“. i.15 ECC Report 94: “Technical requirements for UWB LDC devices to ensure the protection of FWA Systems“ Nicosia, December 2006. i.16 ECC Report 123: “The impact of Object Discrimination and Characterization (ODC) applications Using Ultra-Wideband (UWB) technology on radio services“, Viln
43、ius, September 2008. i.17 ETSI TR 103 181-1 (V1.1.1) (07-2015): “Short Range Devices (SRD) using Ultra Wide Band (UWB); Technical Report; Part 1: UWB signal characteristics and overview CEPT/ECC and EC regulation“. i.18 ETSI TR 103 181-2 (V1.1.1) (06-2014): “Electromagnetic compatibility and Radio s
44、pectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band (UWB);Transmission characteristics; Part 2: UWB mitigation techniques“. i.19 M. Mahler, et.al.: “Radar sensor to DETERMINE POSITION And PHYSIOLOGICAL PARAMETERS OF A PERSON IN A VEHICLE“, European Microwave Week 2002, Milano. i.2
45、0 C. G. Bilich: “Bio-medical sensing using ultra-wideband communications and radar technology: a feasibility study“, in Proceedings of the 1stInternational Pervasive Health Conference and Workshops, Pervasive Health, pp. 1-9, November-December 2006. i.21 ECC Report 251: “The impact of UWB applicatio
46、ns on board aircraft in the band 6-8.5 GHz on FS links used around airports and on EESS earth stations“, 2016. i.22 ECC Report 234:“Analyses of LDC UWB mitigation techniques with respect to incumbent radiocommunication services within the band 3.1 to 3.4 GHz“, 2015. ETSI ETSI TR 103 313 V1.1.1 (2017
47、-03) 8 i.23 ECC Report 175: “Co-existence study considering UWB applications inside aircraft and existing radio services in 3.1-4.8 GHz/6.0-8.5 GHz“, 2012. i.24 ECC Report 170: “Specific UWB applications in the bands 3.4 - 4.8 GHz and 6 - 8.5 GHz LAES, LT2 and LTA“, 2011. 3 Definitions and abbreviat
48、ions 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI TR 103 181-1 i.17 and ETSI TR 103 181-2 i.18 apply. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ADC Analogue-to-Digital converter BMA Building Mat
49、erial Analyses BWA Broad Band Wireless Access CAGR Compound Annual Growth Rate CEPT Conference Europenne des Administrations de Postes et des Telecommunications CMOS Complementary Metal-Oxide Semiconductor CVD Cardiovascular diseases DAA Detect and Avoid DAC Digital-to-Analogue Converter dBm deciBel relative to 1 mW DC Direct Current e.i.r.p. equivalent isotropic radiated power EC European Commission ECC Electronic Communications Committee ECG Electrocardiograph EEG Electroencephalogram EESS Earth Explorat
