1、 ETSI TS 101 851-5-1 V2.1.1 (2008-01)Technical Specification Satellite Earth Stations and Systems (SES);Satellite Component of UMTS/IMT-2000;Part 5: UE Radio Transmission and Reception;Sub-part 1: G-family (S-UMTS-G 25.101)ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 2 Reference DTS/SES-00256-5 Keyword
2、s FDD, IMT-2000, radio, satellite, transmission, UMTS, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Imp
3、ortant notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is t
4、he Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Inf
5、ormation on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No
6、part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are
7、Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 3 Contents Intellectual Property Rights6 Foreword.6 Introduction 6 1 Scope 8 2 Re
8、ferences 8 2.1 Normative references .8 2.2 Informative references9 3 Definitions symbols and abbreviations 9 3.1 Definitions9 3.2 Symbols10 3.3 Abbreviations .10 4 General .11 4.1 Introduction 11 4.2 Relationship between Minimum Requirements and Test Requirements11 4.3 Control and monitoring functio
9、ns 11 4.3.1 Minimum requirement 12 5 Frequency bands and channel arrangement12 5.1 General .12 5.2 Frequency bands.12 5.3 TX-RX frequency separation .12 5.4 Channel arrangement12 5.4.1 Channel spacing12 5.4.2 Channel raster .12 5.4.3 Channel number12 5.4.4 UARFCN 13 6 Transmitter Characteristics.13
10、6.1 General .13 6.2 Transmission power .13 6.2.1 UE Maximum output power .13 6.2.2 UE Relative code domain power accuracy .13 6.3 Frequency Error14 6.4 Output power dynamics14 6.4.1 Open loop power control 14 6.4.1.1 Minimum requirement 14 6.4.2 Inner loop power control in the uplink14 6.4.2.1 Power
11、 control steps .15 6.4.2.1.1 Minimum requirement.15 6.4.3 Minimum output power 15 6.4.3.1 Minimum requirement 15 6.4.4 Out-of-synchronization handling of output power16 6.4.4.1 Minimum requirement 16 6.4.4.2 Test case16 6.5 Transmit ON/OFF power .18 6.5.1 Transmit OFF power.18 6.5.1.1 Minimum requir
12、ement 18 6.5.2 Transmit ON/OFF Time mask18 6.5.2.1 Minimum requirement 18 6.5.3 Change of TFC .20 6.5.3.1 Minimum requirement 20 6.5.4 Power setting in uplink compressed mode21 6.5.4.1 Minimum requirement 21 6.6 Output RF spectrum emissions.23 ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 4 6.6.1 Occupi
13、ed bandwidth .23 6.6.2 Out of band emission 23 6.6.2.1 Spectrum emission mask.23 6.6.2.1.1 Minimum requirement.24 6.6.2.2 Adjacent Channel Leakage power Ratio (ACLR).24 6.6.2.2.1 Minimum requirement.24 6.6.3 Spurious emissions .25 6.6.3.1 Minimum requirement 25 6.7 Transmit intermodulation .25 6.7.1
14、 Minimum requirement 26 6.8 Transmit modulation 26 6.8.1 Transmit pulse shape filter26 6.8.2 Error Vector Magnitude26 6.8.2.1 Minimum requirement 27 6.8.3 Peak code domain error 27 6.8.3.1 Minimum requirement 27 6.8.4 Relative code domain error.27 6.8.4.1 Minimum requirement 28 6.8.5 Phase discontin
15、uity for uplink DPCH.28 6.8.5.1 Minimum requirement 28 7 UE Receiver characteristics28 7.1 General .28 7.2 Diversity characteristics .29 7.3 Reference sensitivity level29 7.3.1 Minimum requirement 29 7.4 Maximum input level .29 7.4.1 Minimum requirement for DPCH reception .29 7.5 Adjacent Channel Se
16、lectivity (ACS)29 7.5.1 Minimum requirement 30 7.6 Blocking characteristics .30 7.6.1 Minimum requirement (In-band blocking) .30 7.6.2 Minimum requirement (Out of-band blocking) 31 7.6.3 Minimum requirement (Narrow band blocking).31 7.7 Spurious response.31 7.7.1 Minimum requirement 31 7.8 Intermodu
17、lation characteristics 32 7.8.1 Minimum requirement 32 7.8.2 Minimum requirement (Narrow band)32 7.9 Spurious emissions.33 7.9.1 Minimum requirement 33 7.10 Maximum Doppler .33 8 Performance requirement .33 8.1 General .33 8.2 Demodulation of DCH in static propagation conditions 34 8.2.1 Minimum req
18、uirement 34 8.3 Demodulation of DCH in multi-path fading conditions .34 8.3.1 Reception under ITU defined A, B, C channels and aeronautical 34 8.3.1.1 Minimum performance requirement - LOS.34 8.3.1.2 Minimum performance requirement - NLOS36 8.3.1.3 Minimum performance requirement - Aeronautical37 8.
19、3.2 Reception of combined satellite and CGCs signals 37 8.3.3 Reception of CGC only signals.40 8.4 Demodulation of DCH in satellite diversity mode .40 8.4.1 Minimum requirement 40 8.5 Demodulation of DCH in CGC Transmit diversity modes.41 8.6 Demodulation in Handover conditions.41 8.7 Detection of B
20、roadcast Channel (BCH) .41 8.7.1 Minimum requirement 41 8.8 Demodulation of Paging Channel (PCH) .43 8.8.1 Minimum requirement 43 ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 5 8.9 Detection of Acquisition Indicator (AI) .44 8.9.1 Minimum requirement 44 9 Performance requirements for Multimedia Broadca
21、st Multicast Service (MBMS).45 9.1 Demodulation of MCCH 45 9.1.1 Minimum requirement 45 9.2 Demodulation of MTCH 46 9.2.3 Minimum requirement 46 Annex A (normative): Measurement channels48 A.1 General .48 A.2 Uplink reference measurement channel .48 A.2.2 UL reference measurement channel (1,2 kbit/s
22、).48 A.2.3 UL reference measurement channel (4,75 kbit/s).49 A.3 Downlink reference measurement channel 50 A.3.1 DL reference measurement channel (1,2 kbit/s).50 A.3.2 DL reference measurement channel (4,75 kbit/s).51 A.3.3 DL reference measurement channel (64 kbit/s)52 A.3.4 DL reference measuremen
23、t channel (144 kbit/s)53 A.3.5 DL reference measurement channel (384 kbit/s)54 A.4 DL reference parameters for PCH tests55 A.5 DL reference parameters for MBMS tests56 A.5.1 MCCH 56 A.5.2 MTCH 56 Annex B (normative): Propagation conditions58 B.1 Static propagation condition.58 B.2 Multi-path fading
24、propagation condition58 B.2.1 Satellite channels58 B.2.2 Combined Satellite and CGC channels 59 Annex C (normative): Downlink Physical Channels.60 C.1 General .60 C.2 Connection set-up.60 C.3 During connection60 C.3.1 Measurement of Rx Characteristics60 C.3.2 Measurement of performance requirements
25、.61 C.4 W-CDMA Modulated Interferer 62 Annex D (normative): UE Environmental conditions.63 D.1 General .63 D.2 Environmental requirements 63 D.2.1 Temperature .63 D.2.2 Voltage .63 D.2.3 Vibration.64 Annex E (informative): Change History 65 History 66 ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 6 Inte
26、llectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rig
27、hts (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including I
28、PR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been
29、 produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document is specifying the Satellite Radio Interface referenced as SRI Family G at ITU-R, in the frame of the modification of ITU-R Recommendation M.1457-5 10. This modification has been approved at ITU-R S
30、G8 meeting in November 2005. The present document is part 5, sub-part 1 of a multi-part deliverable covering Satellite Earth Stations and Systems (SES); Satellite Component of UMTS/IMT-2000; G-family, as identified below: Part 1: “Physical channels and mapping of transport channels into physical cha
31、nnels“; Part 2: “Multiplexing and channel coding“; Part 3: “Spreading and modulation“; Part 4: “Physical layer procedures“; Part 5: “UE Radio Transmission and Reception“; Sub-part 1: “G-family (S-UMTS-G 25.101)“; Part 6: “Ground stations and space segment radio transmission and reception“. Introduct
32、ion S-UMTS stands for the Satellite component of the Universal Mobile Telecommunication System. S-UMTS systems will complement the terrestrial UMTS (T-UMTS) and inter-work with other IMT-2000 family members through the UMTS core network. S-UMTS will be used to deliver 3rdgeneration mobile satellite
33、services (MSS) utilizing either low (LEO) or medium (MEO) earth orbiting, or geostationary (GEO) satellite(s). S-UMTS systems are based on terrestrial 3GPP specifications and will support access to GSM/UMTS core networks. NOTE 1: The term T-UMTS will be used in the present document to further differ
34、entiate the Terrestrial UMTS component. Due to the differences between terrestrial and satellite channel characteristics, some modifications to the terrestrial UMTS (T-UMTS) standards are necessary. Some specifications are directly applicable, whereas others are applicable with modifications. Simila
35、rly, some T-UMTS specifications do not apply, whilst some S-UMTS specifications have no corresponding T-UMTS specification. ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 7 Since S-UMTS is derived from T-UMTS, the organization of the S-UMTS specifications closely follows the original 3rdGeneration Partne
36、rship Project (3GPP) structure. The S-UMTS numbers have been designed to correspond to the 3GPP terrestrial UMTS numbering system. All S-UMTS specifications are allocated a unique S-UMTS number as follows: S-UMTS-n xx.yyy Where: The numbers xx and yyy correspond to the 3GPP-numbering scheme. n (n=A,
37、 B, C, ) denotes the family of S-UMTS specifications. An S-UMTS system is defined by the combination of a family of S-UMTS specifications and 3GPP specifications, as follows: If an S-UMTS specification exists it takes precedence over the corresponding 3GPP specification (if any). This precedence rul
38、e applies to any references in the corresponding 3GPP specifications. NOTE 2: Any references to 3GPP specifications within the S-UMTS specifications are not subject to this precedence rule. For example, an S-UMTS specification may contain specific references to the corresponding 3GPP specification.
39、If an S-UMTS specification does not exist, the corresponding 3GPP specification may or may not apply. The exact applicability of the complete list of 3GPP specifications shall be defined at a later stage. ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 8 1 Scope The present document is to establish the mi
40、nimum RF characteristics for the User Equipment (UE). 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. Non-specific reference may be made only to a com
41、plete document or a part thereof and only in the following cases: - if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which are not found to be publicly availa
42、ble in the expected location might be found at http:/docbox.etsi.org/Reference. For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Fur
43、thermore, the reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE: While any hy
44、perlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For
45、non-specific references, the latest edition of the referenced document (including any amendments) applies. 1 ETSI TS 101 851-1-1: “Satellite Earth Stations and Systems (SES); Satellite Component of UMTS/IMT-2000; Part 1: Physical channels and mapping of transport channels into physical channels; Sub
46、-part 1: G-family (S-UMTS-G 25.211)“. 2 ETSI TS 101 851-2-1: “Satellite Earth Stations and Systems (SES); Satellite Component of UMTS/IMT-2000; Part 2: Multiplexing and channel coding; Sub-part 1: G-family (S-UMTS-G 25.212)“. 3 ETSI TS 101 851-3-1: “Satellite Earth Stations and Systems (SES); Satell
47、ite Component of UMTS/IMT-2000; Part 3: Spreading and modulation; Sub-part 1: G-family (S-UMTS-G 25.213)“. 4 ETSI TS 101 851-4-1: “Satellite Earth Stations and Systems (SES); Satellite Component of UMTS/IMT-2000; Part 4: Physical layer procedures; Sub-part 1: G-family (S-UMTS-G 25.214)“. 5 ETSI TR 1
48、21 905: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Vocabulary for 3GPP Specifications (3GPP TR 21.905)“. 6 ETSI TS 125 101: “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (
49、3GPP TS 25.101)“. 7 ETSI TS 125 306: “Universal Mobile Telecommunications System (UMTS); UE Radio Access capabilities (3GPP TS 25.306)“. ETSI ETSI TS 101 851-5-1 V2.1.1 (2008-01) 9 8 ETSI TBR 042: “Satellite Personal Communications Networks (S-PCN); Mobile Earth Stations (MES), including handheld earth stations, for S-PCN in the 2,0 GHz bands under the Mobile Satellite Service (MSS); Terminal essential requirements“. 9 ETSI TS 145 004: “Digital cellular telecommunications system (Phase 2+); Modulation (3GPP TS 45.004)“. 2.2 Informative reference
