1、 ETSI TS 101 852-2-1 V1.2.1 (2003-07)Technical Specification Broadband Radio Access Networks (BRAN);HIPERLAN Type 2;Conformance testing for the Cell based Convergence Layer;Part 2: UNI Service Specific Convergence Sublayer (SSCS);Sub-part 1: Procotol Implementation ConformanceStatement (PICS) profor
2、maETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 2 Reference RTS/BRAN-0024TA3-2-1 Keywords access, HIPERLAN, PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif
3、enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in c
4、ontents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the doc
5、ument may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be r
6、eproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its M
7、embers. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 3 Contents Intellectual P
8、roperty Rights4 Foreword.4 Introduction 4 1 Scope 5 2 References 5 3 Definitions and abbreviations.5 3.1 Definitions5 3.2 Abbreviations .6 4 Conformance to this PICS proforma specification.6 Annex A (normative): Protocol ICS proforma for TS 101 763-2.7 A.1 Guidance for completing the PICS proforma.7
9、 A.1.1 Purposes and structure7 A.1.2 Abbreviations and conventions 7 A.1.3 Instructions for completing the PICS proforma9 A.2 Identification of the implementation 10 A.2.1 Date of the statement10 A.2.2 Implementation Under Test (IUT) identification .10 A.2.3 System Under Test (SUT) identification10
10、A.2.4 Product supplier11 A.2.5 Client (if different from product supplier)11 A.2.6 PICS contact person .12 A.3 Identification of the TS 101 763-2 .12 A.4 Global statement of conformance.12 A.5 Roles.13 A.6 PICS for Mobile Terminal MT or Access Point AP.13 A.6.1 Service Specific Convergence Sublayer
11、procedures 13 A.6.2 SSCS_PDUs involved 13 A.6.3 SSCS PDU parameters .14 A.6.4 CL Information elements parameters .15 History 17 ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The
12、 information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available fro
13、m the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETS
14、I SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is part 2, sub-part 1 of a multi-part
15、 deliverable. Full details of the entire series can be found in part 1, sub-part 1 5. Introduction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a stateme
16、nt is called a Protocol Implementation Conformance Statement (PICS). ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 5 1 Scope The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for the TS 101 763-2 1 in compliance with the relevant requirements, and in accorda
17、nce with the relevant guidance given in ISO/IEC 9646-7 4 and ETS 300 406 2. It details in tabular form the implementation options, i.e. the optional functions additional to those which are mandatory to implement. 2 References The following documents contain provisions which, through reference in thi
18、s text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Re
19、ferenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 101 763-1 (V1.1.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Cell based Convergence Layer; Part 1: Common Part“. 2 ETSI ETS 300 406:
20、“Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-7:
21、 “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 5 ETSI TS 101 852-1-1 (V1.2.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Conformance testing for the Cell based Convergence Layer
22、; Part 1: Common part; Sub-part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 101 763-2 1, ISO/IEC 9646-1 3 and in ISO/IEC 9646-7 4 and the following a
23、pply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented. The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information
24、object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 6 3.2 A
25、bbreviations For the purposes of the present document, the following abbreviations apply: AP Access Point CL Convergence Layer DLC Data Link Control ICS Implementation Conformance Statement IUT Implementation Under Test MAC Medium Access Control MT Mobile Terminal PDU Protocol Data Unit PICS Protoco
26、l ICS RLC Radio Link Control SCS System Conformance Statement SUT System Under Test 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS profor
27、ma given in annex A, and shall preserve the numbering/naming and ordering of the proforma items. An PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07)
28、7 Annex A (normative): Protocol ICS proforma for TS 101 763-2 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intende
29、d purposes and may further publish the completed PICS. A.1 Guidance for completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in TS 101 763-2 may provide information ab
30、out the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: - guidance for completing the PICS proforma; - identification of the implementation; - identification of the TS 101 763-2 ; - global statement of conformance; -
31、roles; - major capabilities; - PDUs; - PDU parameters. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7. Item column The item column contains a number which identifi
32、es the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 8 Status column The following notations, def
33、ined in ISO/IEC 9646-7, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement n
34、ot to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined immediately following the table. ci conditi
35、onal - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined immediately following the table. i irrelevant (out-of-scope) - capability outside th
36、e scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ statuses above. Reference column The reference column makes reference to TS 101 763-2 , except where explicitly stated otherwi
37、se. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer requ
38、ired (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one profile and not supported for an
39、other. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and
40、 which takes the value TRUE if and only if that profile is to be used. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N NOTE 2: As stated in ISO/IEC 9646-7, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid param
41、eter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 9 Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The following notati
42、ons are used: - range of values: example: 5 20 - list of values: , , ., example: 2 ,4 ,6 ,8, 9 example: 1101B, 1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: reject(1), accept(2) - length: size ( ) example: size (1 8) Values supported column The values supported c
43、olumn shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS proforma a unique reference exists,
44、used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 2
45、: A.5/4 is the reference to the answer of item 4 in table 5 of annex A. EXAMPLE 3: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in table 6 of annex A. Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a claus
46、e or table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. A.1.3 Instructions for completing the PICS proforma The supplier of the implementation shall complete the PICS proforma in each of the spaces provided. In particular, an exp
47、licit answer shall be entered, in each of the support or supported column boxes provided, using the notation described in clause A.1.2. If necessary, the supplier may provide additional comments in space at the bottom of the tables or separately. More detailed instructions are given at the beginning
48、 of the different clauses of the PICS proforma. ETSI ETSI TS 101 852-2-1 V1.2.1 (2003-07) 10A.2 Identification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test (SUT) should be filled in so as to provide as much deta
49、il as possible regarding version numbers and configuration options. The product supplier information and client information should both be filled in if they are different. A person who can answer queries regarding information supplied in the PICS should be named as the contact person. A.2.1 Date of the statement . A.2.2 Implementation Under Test (IUT) identification IUT name: . . IUT version: . A.2.3 System Under Test (SUT) identification SUT name: . . Hardware configuration: . . . Operating system: . ETSI ETSI TS 101 852-2-1 V1.2.1 (
