1、 ETSI TS 102 148-1-1 V1.2.1 (2004-04)Technical Specification Broadband Radio Access Networks (BRAN);HIPERACCESS;Conformance testing for the Packet based Convergence Layer;Part 1: Common part;Sub-part 1: Protocol Implementation ConformanceStatement (PICS) proformaETSI ETSI TS 102 148-1-1 V1.2.1 (2004
2、-04) 2 Reference RTS/BRAN-0034T04-1-1R1 Keywords access, ATM, broadband, hiperaccess, PICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre
3、la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents bet
4、ween such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may b
5、e subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced e
6、xcept as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIP
7、HONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 148-1-1 V1.2.1 (2004-04) 3 Contents Intellectual Property Rig
8、hts4 Foreword.4 Introduction 4 1 Scope 5 2 References 5 3 Definitions and abbreviations.5 3.1 Definitions5 3.2 Abbreviations .6 4 Conformance to this PICS proforma specification.6 Annex A (normative): Protocol ICS proforma for TS 102 117-1.7 A.1 Guidance for completing the proforma 7 A.1.1 Purposes
9、and structure7 A.1.2 Abbreviations and conventions 7 A.1.3 Instructions for completing the PICS proforma9 A.2 Identification of the implementation 9 A.2.1 Date of the statement9 A.2.2 Implementation Under Test (IUT) identification .10 A.2.3 System Under Test (SUT) identification10 A.2.4 Product supp
10、lier10 A.2.5 Client 11 A.2.6 PICS contact person .11 A.3 Identification of the protocol12 A.4 Global statement of conformance.12 A.5 Roles.12 Annex B (informative): Bibliography.13 History 14 ETSI ETSI TS 102 148-1-1 V1.2.1 (2004-04) 4 Intellectual Property Rights IPRs essential or potentially essen
11、tial to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notifi
12、ed to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can
13、be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (B
14、RAN). The present document is part 1,sub-part 1 of a multi-part covering testing specification for the Packet based Convergence Layer of the BRAN HIPERACCESS system, as identified below: Part 1: “Common part“; Sub-part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Sub-part 2: “
15、Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS)“. Part 2: “Ethernet Service Specific Convergence Sublayer (SSCS)“. Introduction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been i
16、mplemented for a telecommunication specification. When such a statement is based on a protocol, it is called PICS. ETSI ETSI TS 102 148-1-1 V1.2.1 (2004-04) 5 1 Scope The present document provides the PICS proforma for TS 102 117-1 1 in compliance with the relevant requirements, and in accordance wi
17、th the relevant guidance given in ISO/IEC 9646-7 4 and ETS 300 406 2. It details in tabular form the implementation options, i.e. the optional functions additional to those, which are mandatory to implement. 2 References The following documents contain provisions which, through reference in this tex
18、t, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referen
19、ced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 102 117-1: “Broadband Radio Access Networks (BRAN); HIPERACCESS; Packet based Convergence Layer; Part 1: Common Part“. 2 ETSI ETS 300 406: “Methods for tes
20、ting and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 3 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 4 ISO/IEC 9646-7: “Information te
21、chnology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 102 117-1 1, ISO/IEC 9646-1 3, ISO
22、/IEC 9646-7 4 and the following apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented. The ICS can take several forms: protocol ICS, profile ICS, p
23、rofile specific ICS, information object ICS, etc. ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification ETSI ETSI TS 102
24、 148-1-1 V1.2.1 (2004-04) 6 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AAL ATM Adaptation Layer AP Access Point ATM Asynchronous Transfer Mode BRAN Broadband Radio Access Networks (Project) CL Convergence Layer ETSI European Telecommunications Stan
25、dards Institute PDU Protocol Data Unit TS Technical Specification IUT Under Test SUT System Under Test 4 Conformance to this PICS proforma specification If an implementation is claimed to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equ
26、ivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and ordering of the proforma items. A PICS, which conforms to the present document, shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETS
27、I ETSI TS 102 148-1-1 V1.2.1 (2004-04) 7 Annex A (normative): Protocol ICS proforma for TS 102 117-1 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex
28、 so that it can be used for its intended purposes and may further publish the completed PICS. A.1 Guidance for completing the proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in TS 10
29、2 117-1 may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: - Guidance for completing the PICS proforma; - Identification of the implementation; - Identification of the protocol; - Global
30、 statement of conformance; - Roles; - Major capabilities; - PDUs and PDU parameters. A.1.2 Abbreviations and conventions The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7. Item column The item column co
31、ntains a number, which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Status column The following notations, defined in ISO/I
32、EC 9646-7, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - there is a requirement not to use thi
33、s capability in the given context. ETSI ETSI TS 102 148-1-1 V1.2.1 (2004-04) 8 o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined immediately
34、following the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined immediately following the table. i irrelevant (out-of
35、-scope) - capability outside the scope of the reference specification. No answer is requested from the supplier. NOTE 1: This use of “i“ status is not to be confused with the suffix “i“ to the “o“ and “c“ statuses above. Reference column The reference column makes reference to TS 102 117-1, except w
36、here explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation
37、. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a system, it is necessary to be able to answer that a capability is supported for one pr
38、ofile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (e.g. ?3). This expression shall be given in the space for comments provided at the bottom of the table. It uses predicates defined in the SCS, each of which
39、refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N. NOTE 2: As stated in ISO/IEC 9646-7, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no
40、 ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the semantics of that parameter are supported. Values allowed column The values allowed column contains the type, the list, the range, or the length of values allowed. The following notations are used:
41、 - range of values: example: 5 20 - list of values: , , ., example: 2 ,4 ,6 ,8, 9 example: 1101B, 1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: reject(1), accept(2) - length: size ( ) example: size (1 8) ETSI ETSI TS 102 148-1-1 V1.2.1 (2004-04) 9 Values supporte
42、d column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS profo
43、rma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b,
44、 etc.), respectively. EXAMPLE 2: A.5/4 is the reference to the answer of item 4 in table 5 of annex A. EXAMPLE 3: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in table 6 of annex A. Prerequisite line A prerequisite line takes the form: Prerequisite: . A
45、prerequisite line after a clause or before a table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. A.1.3 Instructions for completing the PICS proforma The supplier of the implementation shall complete the PICS proforma in each of th
46、e spaces provided. In particular, an explicit answer shall be entered, in each of the support or supported column boxes provided, using the notation described in clause A.1.2. If necessary, the supplier may provide additional comments in space at the bottom of the tables or separately. More detailed
47、 instructions are given at the beginning of the different clauses of the PICS proforma. A.2 Identification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test (SUT) should be filled in so as to provide as much detail a
48、s possible regarding version numbers and configuration options. A.2.1 Date of the statement Table A.1: Date of statement Date of statement Day Month Year ETSI ETSI TS 102 148-1-1 V1.2.1 (2004-04) 10A.2.2 Implementation Under Test (IUT) identification The supplier of the implementation shall enter in
49、formation necessary to uniquely identify the IUT in table A.2. Table A.2: IUT identification IUT identification IUT name IUT version A.2.3 System Under Test (SUT) identification The supplier of the implementation shall enter information necessary to uniquely identify the SUT in table A.3. Table A.3: SUT identification SUT identification SUT name Hardware configuration Operating system A.2.4 Product supplier Table A.4: Product supplier Product supplier Name Address Phone No. Fax No. E-mail address Additional information ETSI ETSI TS 102 14
