1、 ETSI TS 102 210 V1.2.1 (2005-01)Technical Specification Broadband Radio Access Networks (BRAN);HIPERMAN;System profilesETSI ETSI TS 102 210 V1.2.1 (2005-01) 2 Reference RTS/BRAN-0040005r1 Keywords access, broadband, FWA, HiperMAN, profile, radio, system ETSI 650 Route des Lucioles F-06921 Sophia An
2、tipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The pre
3、sent document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printer
4、s of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/s
5、tatus/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restric
6、tion extend to reproduction in all media. European Telecommunications Standards Institute 2005. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for th
7、e benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 210 V1.2.1 (2005-01) 3 Contents Intellectual Property Rights4 Foreword.4 1 Scope 5 2 References 5 3 Definitions, symbols and abbreviations .5 3
8、.1 Definitions5 3.2 Symbols5 3.3 Abbreviations .5 4 System profiles.6 4.1 DLC profiles.6 4.1.1 Basic packet PMP DLC profile.6 4.1.2 Basic packet Mesh DLC profile7 4.2 PHY profiles.9 4.2.1 1 MHz channelization PHY profile 10 4.2.2 3 MHz channelization PHY profile 10 4.2.3 7 MHz channelization PHY pro
9、file 11 4.2.4 10 MHz channelization PHY profile 12 4.3 Duplexing selection13 4.4 Power class profiles13 Annex A (informative): Bibliography.14 History 15 ETSI ETSI TS 102 210 V1.2.1 (2005-01) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been
10、 declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“,
11、which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs
12、 not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document describes the s
13、ystem profile specifications for High PERformance Radio Metropolitan Area Network (HiperMAN), which operate on frequencies below 11 GHz. System profiles provide recommended implementations of HiperMAN compliant systems. ETSI ETSI TS 102 210 V1.2.1 (2005-01) 5 1 Scope The present document specifies t
14、he HiperMAN system profiles. System profiles provide recommended implementations of HiperMAN compliant systems. Compliance with the HiperMAN specification does not require compliance with the present document. 2 References Void. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purpos
15、es of the present document, the following terms and definitions apply: Base Station (BS): generalized equipment consisting of one or more Base Station Controllers and one or more Base Station Transceivers guard time: time at the beginning or end of each burst to allow power ramping up and down half
16、duplex: equipment that cannot transmit and receive at the same time Receive-Transmit Transition Gap (RTG): time to switch from receive to transmit at the BS Subscriber Station (SS): generalized equipment consisting of a Subscriber Station Controller and Subscriber Station Transceiver Transmit-Receiv
17、e Transition Gap (TTG): time to switch from transmit to receive at the BS 3.2 Symbols For the purposes of the present document, the following symbols apply: BW Nominal channel bandwidth (Hz) bT Useful OFDM symbol time (s) FT Frame duration (ms) gT OFDM symbol guard time or CP time (s) sT OFDM symbol
18、 time (s) 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: AAS Adaptive Antenna System AES Advanced Encryption Standard ARQ Automatic Repeat Request BER Bit Error Rate BPSK Binary Phased Shift Keying BS Base Station BW BandWidthCBC Cipher Block Chaining
19、CCM CORBA Component Model ETSI ETSI TS 102 210 V1.2.1 (2005-01) 6 CID Connection IDentifier CP Cyclic PrefixCRC Cyclic Redundancy Check DES Data Encryption StandardDFS Dynamic Frequency Selection DHCP Dynamic Host Configuration Protocol DLC Data Link Layer FDC Frame Duration Code FDD Frequency Divis
20、ion Duplexing H-FDD Half duplex Frequency Division Duplexing HM HiperMAN PHY Physical layer PMP Point to Multi Point QPSK Quadrature Phase Shift Keying RSA Rivest, Shamir and Adleman RTG Receive / Transmit transition Gap Rx Receive SNMP Simple Network Management Protocol SS Subscriber Station TDD Ti
21、me Division Duplexing TFTP Trivial File Transfer Protocol TTG Transmit / receive Transition Gap Tx Transmit 4 System profiles A system profile consists of four components: a DLC profile, a PHY profile, a duplexing selection (FDD and/or TDD) and a power class selection. A system may implement multipl
22、e profiles of each component. 4.1 DLC profiles 4.1.1 Basic packet PMP DLC profile Profile identifier: prof_HM_DLC_PMP. Table 1 lists the optional DLC features and whether their implementation is required to comply with this profile. ETSI ETSI TS 102 210 V1.2.1 (2005-01) 7 Table 1: Optional feature r
23、equirements prof_HM_DLC_PMP Feature Required? Conditions / Notes Packet convergence sublayer Payload header suppression Ipv4 over Ethernet Ethernet Yes No Yes Yes ATM convergence sublayer No Provisioned connections No Classification of packets on incoming physical port No Multicast polling groups Mu
24、lticast polling Yes CRC functionality Yes Elective per connection Dynamic services Yes Unsolicited grant service functionality No Real-Time Polling services No Best effort services Yes Non-Real-Time Polling services Yes ryptographic suites: No data encryption, no data authentication and 3-DES with 1
25、28 bit key CBC-Mode 56 bit DES, no data authentication and 3-DES with 128 bit key No data encryption, no data authentication and RSA with 1 024 bit key CBC-Mode 56 bit DES, no data authentication and RSA with 1 024 bit key AES CCM-Mode, no data authentication and AES with 128-bit key No Yes No No No
26、 Undecodable initial ranging feature Conditional Required for SS Not required for BS ARQ No If used, a minimum of 8 simultaneous ARQ connections shall be supportable. Mesh No If supported, apply prof_HM_DLC2 AAS No BS capability for support of manageable SS (creating secondary management connections
27、, DHCP, TFTP, SNMP, etc.) Yes 4.1.2 Basic packet Mesh DLC profile Profile identifier: prof_HM_DLC_Mesh. This profile shall only be used in combination with TDD duplexing. Table 2 lists the optional DLC features and whether their implementation is required to comply with this profile. ETSI ETSI TS 10
28、2 210 V1.2.1 (2005-01) 8 Table 2: Optional feature requirements prof_HM_DLC_Mesh Feature Required? Conditions / Notes Prof_HM_DLC1 for packet PMP Yes Packet convergence sublayer Payload header suppression Ipv4 over Ethernet Ethernet Yes No Yes Yes ATM convergence sublayer Support of PVCs VC switched
29、 connections VP switched connections No Provisioned connections No Multicast polling groups Multicast polling N/A CRC functionality Yes Elective per connection Dynamic services No Unsolicited grant service functionality N/A Real-Time Polling services N/A Best effort services Yes Non-Real-Time Pollin
30、g services N/A ryptographic suites: No data encryption, no data authentication and 3-DES with 128 bit key CBC-Mode 56 bit DES, no data authentication and 3-DES with 128 bit key No data encryption, no data authentication and RSA with 1 024 bit key CBC-Mode 56 bit DES, no data authentication and RSA w
31、ith 1 024 bit key AES CCM-Mode, no data authentication and AES with 128-bit key No Yes No No No Undecodable initial ranging feature N/A ARQ YesAAS No DFS Conditional Required when intended for license exempt bands. Not required when intended for licensed bands. Support of ARQ functionality is mandat
32、ory as a capability, but may be turned on or off on a per packet basis. ARQ shall be used when the reliability bit in the Mesh CID is set to 1, and shall not be used otherwise. ARQ parameters shall be set to: ARQ Window Size = 64DEC. ARQ Retry Timeout = DECFT2, with FT the PHY dependent frame durati
33、on in s. ARQ Fragment Lifetime = DECFT 2/ , with FT the PHY dependent frame duration in s. ARQ RX Purge Time Timeout = DECFT2, with FT the PHY dependent frame duration in s. ARQ Sync Loss Timeout = 0. ARQ Deliver in Order = 0. ETSI ETSI TS 102 210 V1.2.1 (2005-01) 9 4.2 PHY profiles Table 3 lists th
34、e common minimum performance requirements with which all PHY profiles shall comply. Table 3: Minimum performance requirements Capability Minimum performance Tx Dynamic range BS SS SS with sub-channelization 10 dB 30 dB 50 dB Tx Power Level minimum adjustment step 1 dB Tx Power Level minimum relative
35、 step accuracy 50 % of step size, but not more than 4 dB Tx Spectral flatness Absolute difference between adjacent carriers: Deviation of average energy in each carrier from the measured energy averaged over all 200 active tones: Carriers -50 to -1 and +1 to +50: Carriers -100 to -50 and +50 to +100
36、: 0,1 dB 2 dB +2 dB / -4 dB Spectral mask (OOB) Local regulation Tx relative constellation error: BPSK-1/2 QPSK-1/2 QPSK-3/4 16QAM-1/2 16QAM-3/4 64QAM-2/3 64QAM-3/4 -13,0 dB -16,0 dB -18,5 dB -21,5 dB -25,0 dB -28,5 dB -31,0 dB Rx max. input level on-channel reception tolerance -30 dBm Rx max. input
37、 level on-channel damage tolerance 0 dBm Input Intercept Point -10 dBm Adjacent channel rejection at BER = 10-6for 3 dB degradation C/I 16QAM-3/4 64QAM-3/4 11 dB 4 dB Non-adjacent channel rejection at BER = 10-6for 3 dB degradation C/I 16QAM-3/4 64QAM-3/4 30 dB 23 dB Out of band signal immunity |fbl
38、ocker- fsignal| 100 MHz 100 MHz |fblocker- fsignal| 1 GHz 1GHz |fblocker- fsignal| Idem to non-adj. Channel rejection -30 dBm, 20 dBr -10 dBm, 30 dBr Spurious emissions 30 MHz to 1 GHz (measurement BW: 100 kHz) 1 GHz to 26,5 GHz (measurement BW: 1 MHz) -57 dBm -50 dBm TTG and RTG (TDD only) 50 s SST
39、TG and SSRTG TDD 50 s H-FDD 100 s Reference frequency tolerance BS Mesh system (TDD only) 8 ppm 20 ppm ETSI ETSI TS 102 210 V1.2.1 (2005-01) 104.2.1 1 MHz channelization PHY profile Profile identifier: prof_HM_PHY1.75. Mandatory features: Licensed band usage only. Channel bandwidth BW = 1,75 MHz. Us
40、e with PMP only. SSs shall be capable of operating with any of the Frame Durations indicated in the code set. Systems implementing prof_HM_PHY1.75 shall meet the minimum performance requirements listed in table 4. Table 4: Minimum performance requirements for prof_HM_PHY1.75 Capability Minimum perfo
41、rmance Tb= 128 s BER performance threshold, BER=10-6BPSK-1/2 QPSK-1/2 QPSK-3/4 16QAM-1/2 16QAM-3/4 64QAM-2/3 64QAM-3/4 -94 dBm -91 dBm -89 dBm -84 dBm -82 dBm -77 dBm -76 dBm Reference frequency tolerance SS to BS synchronization tolerance 156,25 Hz Reference time tolerance (Tb/32) / 2 Tg / TbBS sha
42、ll be capable of using at least one allowed value. SS shall be capable of detecting and using entire set of allowed values. 4.2.2 3 MHz channelization PHY profile Profile identifier: prof_HM_PHY3.5. Mandatory features: Licensed band usage only. Channel bandwidth BW = 3,5 MHz. FDC set for mesh:1. SSs
43、 shall be capable of operating with any of the Frame Durations indicated in the code set. Systems implementing prof_HM_PHY3.5 shall meet the minimum performance requirements listed in table 5. ETSI ETSI TS 102 210 V1.2.1 (2005-01) 11Table 5: Minimum performance requirements for prof_HM_PHY3.5 Capabi
44、lity Minimum performance Tb= 64 s BER performance threshold, BER=10-6BPSK-1/2 QPSK-1/2 QPSK-3/4 16QAM-1/2 16QAM-3/4 64QAM-2/3 64QAM-3/4 Threshold change of subchannelization used -91 dBm -88 dBm -86 dBm -81 dBm -79 dBm -74 dBm -73 dBm ()10log 16subchannelsN Reference frequency tolerance SS to BS syn
45、chronization tolerance Mesh to Mesh synchronization tolerance (TDD only) 312,5 Hz 468,75 Hz Reference time tolerance (Tb/32) / 2 Tg / TbBS shall be capable of using at least one allowed value. SS shall be capable of detecting and using entire set of allowed values. 4.2.3 7 MHz channelization PHY pro
46、file Profile identifier: prof_HM_PHY7. Mandatory features: Licensed band usage only. Channel bandwidth BW = 7 MHz. FDC set for mesh:1. SSs shall be capable of operating with any of the Frame Durations indicated in the code set. Systems implementing prof_HM_PHY7 shall meet the minimum performance req
47、uirements listed in table 6. ETSI ETSI TS 102 210 V1.2.1 (2005-01) 12Table 6: Minimum performance requirements for prof_HM_PHY3 Capability Minimum performance Tb= 32 s BER performance threshold, BER=10-6BPSK-1/2 QPSK-1/2 QPSK-3/4 16QAM-1/2 16QAM-3/4 64QAM-2/3 64QAM-3/4 Threshold change if subchannel
48、ization used -88 dBm -85 dBm -83 dBm -78 dBm -76 dBm -71 dBm -70 dBm ()10log 16subchannelsN Reference frequency tolerance SS to BS synchronization tolerance Mesh to Mesh synchronization tolerance (TDD only) 625 Hz 937,5 Hz Reference time tolerance (Tb/32) / 2 Tg/TbBS shall be capable of using at lea
49、st one allowed value. SS shall be capable of detecting and using entire set of allowed values. 4.2.4 10 MHz channelization PHY profile Profile identifier: prof_HM_PHY10. Mandatory features: License-exempt band usage only. Channel bandwidth BW = 10 MHz. TDD operation. BS shall select Frame duration from code set PMP:2, 4, 6, Mesh:1. SSs shall be capable of operating with any of the Frame Durat
