1、 ETSI TS 102 374-1 V1.1.1 (2004-11)Technical Specification Methods for Testing and Specification (MTS);Conformance Test Specification for ITU-T H.248.1;Part 1: Protocol Implementation ConformanceStatement (PICS) proformaETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 2 Reference DTS/MTS-00096-1 Keywords H.2
2、48, IP, MEGACO, PICS, telephony, testing, VoIP ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice
3、Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Do
4、cument Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on th
5、e current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be re
6、produced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Me
7、mbers. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 3 Contents Intellectual Prop
8、erty Rights5 Foreword.5 Introduction 5 1 Scope 6 2 References 6 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .7 4 Conformance to this PICS proforma specification.7 Annex A (normative): PICS proforma for ITU-T Recommendation H.248.18 A.1 Guidance for completing the PICS profor
9、ma.8 A.1.1 Purposes and structure8 A.1.2 Abbreviations and conventions 8 A.1.3 Instructions for completing the PICS proforma10 A.2 Identification of the implementation 10 A.2.1 Date of the statement10 A.2.2 Implementation Under Test (IUT) identification .10 A.2.3 System Under Test (SUT) identificati
10、on10 A.2.4 Product supplier11 A.2.5 Client (if different from product supplier)11 A.2.6 PICS contact person .12 A.3 PICS/System Conformance Statement (SCS) 12 A.4 Identification of the protocol12 A.5 Global statement of conformance.12 A.6 General Remarks 13 A.6.1 General structure of the H.248.1 mes
11、sages 13 A.7 Roles.14 A.8 Media Gateway Controller role14 A.8.1 Major capabilities.14 A.8.2 Subsidiary capabilities15 A.8.2.1 Support of annexes/Packages15 A.8.2.1.1 H.248.1 annex C: Tags for Media Stream Properties15 A.8.2.1.2 H.248.1 annex D: Transport over IP .19 A.8.2.1.2.1 Transport over IP/UDP
12、19 A.8.2.1.2.2 Transport over IP/TCP 20 A.8.2.1.3 H.248.1 annex E: Basic Packages .20 A.8.3 H.248.1 messages and parameters sent by the MGC20 A.8.3.1 H.248.1 message content 21 A.8.3.2 Transactions21 A.8.3.3 Contexts 22 A.8.3.4 Commands 23 A.8.3.4.1 Command Requests.23 A.8.3.4.2 Command Replies .25
13、A.8.4 H.248.1 messages and parameters received by the MGC.26 A.8.4.1 H.248.1 message content 27 A.8.4.2 Transactions27 A.8.4.3 Contexts 28 ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 4 A.8.4.4 Commands 29 A.8.4.4.1 Command Requests.29 A.8.4.4.2 Command Replies .30 A.8.5 H.248.1 descriptors structure33 A
14、.8.6 Timers and Parameters .34 A.8.6.1 Timers.34 A.9 Media Gateway 35 A.9.1 Major capabilities.35 A.9.2 Subsidiary capabilities36 A.9.2.1 Support of annexes/Packages36 A.9.2.1.1 H.248.1 annex C: Tags for Media Stream Properties36 A.9.2.1.2 H.248.1 annex D: Transport over IP .40 A.9.2.1.2.1 Transport
15、 over IP/UDP40 A.9.2.1.2.2 Transport over IP/TCP 41 A.9.2.1.3 H.248.1 annex E: Basic Packages .41 A.9.3 H.248.1 messages and parameters sent by the MG 41 A.9.3.1 H.248.1 message content 42 A.9.3.2 Transactions42 A.9.3.3 Contexts 43 A.9.3.4 Commands 44 A.9.3.4.1 Command Requests.44 A.9.3.4.2 Command
16、Replies .45 A.9.4 H.248.1 messages and parameters received by the MG .48 A.9.4.1 H.248.1 message content 49 A.9.4.2 Transactions49 A.9.4.3 Contexts 51 A.9.4.4 Commands 52 A.9.4.4.1 Command Requests.52 A.9.4.4.2 Command Replies .54 A.9.5 H.248.1 descriptors structure55 A.9.6 Timers and Parameters .56
17、 A.9.6.1 Timers.56 A.9.6.2 IUT Parameters.57 History 58 ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly avail
18、able for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web serve
19、r (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be,
20、 or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Methods for Testing and Specification (MTS). The present document is part 1 of a multi-part deliverable covering Conformance Testing Specification for ITU-T H.2
21、48.1, as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma“. Introduction To evaluate co
22、nformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called an Implementation Conformance Statement (ICS). ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 6 1 Scope The
23、 present document provides the Protocol Implementation Conformance Statement (PICS) proforma for the audiovisual and multimedia systems Infrastructure of audiovisual services - Communication procedures, Gateway control protocol defined in ITU-T Recommendation H.248.1 1 and its corrigendum 2 in compl
24、iance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 5 and ETS 300 406 3. The supplier of a protocol implementation which is claimed to conform to ITU-T Recommendation H.248.1 1 and 2 is required to complete a copy of the PICS proforma provided i
25、n annex A of the present document and is required to provide the information necessary to identify both the supplier and the implementation. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are ei
26、ther specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the e
27、xpected location might be found at http:/docbox.etsi.org/Reference. 1 ITU-T Recommendation H.248.1(2002): “Gateway control protocol: Version 2“. 2 ITU-T Recommendation H.248.1 v2 Corrigendum 1 (2004): “Gateway control protocol: Version 2“. 3 ETSI ETS 300 406 (1995): “Methods for testing and Specific
28、ation (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 4 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 5 ISO/IEC 9646-7 (1995): “Information techn
29、ology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 6 IETF RFC 2327: “SDP: Session Description Protocol“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definit
30、ions given in ITU-T Recommendation H.248.1 1, ISO/IEC 9646-1 4, ISO/IEC 9646-7 5 and the following apply: Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implem
31、ented NOTE: The PICS can take several forms: protocol PICS, profile PICS, profile specific PICS, information object PICS, etc. Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 7 3.2 Abbreviations For
32、 the purposes of the present document, the following abbreviations apply: ICS Implementation Conformance Statement IUT Implementation Under Test MG Media Gateway MGC Media Gateway Controller PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement SCS System Conformance Statement SU
33、T System Under Test 4 Conformance to this PICS proforma specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering/naming and
34、 ordering of the proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1. ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 8 Annex A (normative): PICS proforma for ITU-T Recommendation H.248
35、.1 Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS. A.1
36、Guidance for completing the PICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in ITU-T Recommendation H.248.1 1 and 2 may provide information about the implementation in a standar
37、dized manner. The PICS proforma is subdivided into clauses for the following categories of information: guidance for completing the PICS proforma; identification of the implementation; identification of the protocol; global statement of conformance; roles and major capabilities; subsidiary capabilit
38、ies; coding supported by the IUT; support of annexes; timers and parameters. A.1.2 Abbreviations and conventions The ICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 5. Item column The item column contains
39、a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 9 Status column The fol
40、lowing notations, defined in ISO/IEC 9646-7 5, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (excluded) - t
41、here is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is defined immediately following
42、 the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately following the table; Reference column The reference
43、 column makes reference to ITU-T Recommendation H.248.1 1 with its corrigendum 2 except where explicitly stated otherwise. Support column The supplier of the implementation shall fill in the support column. The following common notations, defined in ISO/IEC 9646-7 5, are used for the support column:
44、 Y or y supported by the implementation; N or n not supported by the implementation; N/A, n/a or no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). If this PICS proforma is completed in order to describe a multiple-profile support in a syste
45、m, it is necessary to be able to answer that a capability is supported for one profile and not supported for another. In that case, the supplier shall enter the unique reference to a conditional expression, preceded by “?“ (for example ?3). This expression shall be given in the space for comments pr
46、ovided at the bottom of the table. It uses predicates defined in the SCS, each of which refers to a single profile and which takes the value TRUE if and only if that profile is to be used. EXAMPLE 1: ?3: IF prof1 THEN Y ELSE N. It is also possible to provide a comment to an answer in the space provi
47、ded at the bottom of the table. NOTE: As stated in ISO/IEC 9646-7 5, support for a received PDU requires the ability to parse all valid parameters of that PDU. Supporting a PDU while having no ability to parse a valid parameter is non-conformant. Support for a parameter on a PDU means that the seman
48、tics of that parameter are supported. References to items For each possible item answer (answer in the support column) within the ICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, fol
49、lowed by the item number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 2: A.5/4 is the reference to the answer of item 4 in table 5 of annex A. EXAMPLE 3: A.6/3b is the reference to the second answer (i.e. in the second support column) of item 3 in table 6 of annex A. ETSI ETSI TS 102 374-1 V1.1.1 (2004-11) 10Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a clause
