1、 ETSI TS 102 385-1 V2.5.1 (2008-12)Technical Specification Broadband Radio Access Networks (BRAN);HiperMAN;Conformance Testing for WiMAX/HiperMAN 1.2.1;Part 1: Protocol Implementation ConformanceStatement (PICS) proformaETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 2 Reference RTS/BRAN-004T002-1R5 Keyword
2、s broadband, DLC, FWA, HiperMAN, MAC, PICS, point-to-multipoint, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse
3、 (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the ref
4、erence version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or ch
5、ange of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyrig
6、ht Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2008. WIMAX Forum 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, t
7、he TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 3 Contents Intellectual Property Rights5 Forew
8、ord.5 1 Scope 6 2 References 6 2.1 Normative references .6 2.2 Informative references7 3 Definitions, symbols and abbreviations .7 3.1 Definitions7 3.2 Symbols7 3.3 Abbreviations .8 4 Conformance to this PICS Proforma Specification9 Annex A (normative): Protocol ICS (PICS) for HiperMAN/WiMAX 10 A.1
9、Guidance for completing PICS Proforma.10 A.1.1 Purposes and Structure .10 A.1.2 Abbreviations and Conventions .10 A.1.3 Instructions for completing the PICS Proforma .12 A.2 Identification of the implementation 12 A.2.1 Date of statement12 A.2.2 Implementation Under Test (IUT) identification .12 A.2
10、.3 System Under Test (SUT) identification13 A.2.4 Product supplier13 A.2.5 Client (if different from product supplier)13 A.2.6 PICS contact person .13 A.3 Identification of the standard14 A.4 Global statement of conformance.14 A.5 System profiles.14 A.5.1 WirelessMAN-SC 14 A.5.2 WirelessMAN-SCa.14 A
11、.5.3 WirelessMAN-OFDM and WirelessHUMAN-OFDM 15 A.5.3.1 SS in PMP topology16 A.5.3.1.1 PHY functions.16 A.5.3.1.2 Convergence sub layer 23 A.5.3.1.3 MAC common part sub layer25 A.5.3.1.4 Construction and Transmission of MAC PDUs 27 A.5.3.2 SS in MESH topology.35 A.5.3.3 BS in PMP topology .36 A.5.3.
12、3.1 PHY functions.36 A.5.3.3.2 Convergence sub layer 41 A.5.3.3.3 MAC common part sub layer43 A.5.3.3.4 Construction and Transmission of MAC PDUs 44 A.5.3.4 BS in MESH topology 53 A.5.4 WirelessMAN-OFDMA and WirelessHUMAN-OFDMA.53 A.6 List of PDUs and their directions.53 A.6.1 Void53 A.6.2 PDUs for
13、MAC layer53 A.6.2.1 PDUs for MAC layer in PMP topology53 A.6.2.1.1 PDUs for network entry and initialization in PMP .53 A.6.2.1.2 PDUs for service flows in PMP 54 A.6.2.1.3 PDUs for ARQ in PMP.55 ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 4 A.6.2.1.4 PDUs for miscellaneous capabilities in PMP56 A.6.2.1
14、.5 PDUs for privacy in PMP .57 A.6.2.2 PDUs for MAC layer in MESH topology.58 A.7 PDU fields58 A.7.1 Fields of PDUs for MAC layer.58 A.7.1.1 PDUs fields for MAC in PMP topology .58 A.7.1.1.1 DL-MAP .58 A.7.1.1.2 DCD 59 A.7.1.1.3 UCD 60 A.7.1.1.4 UL-MAP .61 A.7.1.1.5 RNG-REQ and RNG-RSP 62 A.7.1.1.6
15、SBC-REQ and SBC-RSP 63 A.7.1.1.7 DHCP messages64 A.7.1.1.8 Time of day messages .64 A.7.1.1.9 ARQ messages 65 A.7.1.1.10 MCA-REQ and MCA-RSP .65 A.7.1.1.11 DBPC-REQ and DBPC-RSP 66 A.7.1.1.12 RES-CMD.66 A.7.1.1.13 CLK-CMP.67 A.7.1.1.14 DREG-REQ and DREG-CMD67 A.7.1.1.15 DSX-RVD.68 A.7.1.1.16 TFTP-CP
16、LT and TFTP-RSP.68 A.7.1.1.17 REP-REQ and REP-RSP.69 A.7.1.1.18 AAS-FBCK-REQ and AAS-FBCK-RSP69 A.7.1.1.19 AAS-BEAM messages70 A.7.1.1.20 FPC .71 A.7.1.1.21 REG-REQ and REG-RSP .71 A.7.1.1.22 PKM-REQ and PKM-RSP Messages .73 A.7.1.1.23 DSA-REQ, DSA-RSP and DSA-ACK messages75 A.7.1.1.24 DSC-REQ, DSC-
17、RSP and DSC-ACK messages 79 A.7.1.1.25 DSD-REQ and DSD-RSP messages .82 A.7.1.2 Additional fields of MAC PDUs in MESH topology .83 A.8 Parameters and timers 83 History 85 ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 5 Intellectual Property Rights IPRs essential or potentially essential to the present doc
18、ument may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect o
19、f ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the exis
20、tence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Broadband Radio Access Networks (BRAN). The p
21、resent document specifies the Protocol Implementation Conformance Statement (PICS) for HIgh PERformance Radio Metropolitan Area Network (HiperMAN) and WiMAX, which operates on frequencies between 2 GHz and 11 GHz. The present document has been developed on the basis of preceding versions of HiperMAN
22、 and WiMAX PICS and makes the previous versions obsolete. The present document is part 1 of a multi-part deliverable covering Broadband Radio Access Networks (BRAN); HiperMAN; Conformance Testing for WiMAX/HiperMAN 1.2.1, as identified below: Part 1: “Protocol Implementation Conformance Statement (P
23、ICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS)“. ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 6 1 Scope The present document specifies the Protocol Implementation Conformance Statement (PICS) for HiperMAN/WiMAX per ISO/IEC 9646-7 7 and EG 201 058 9
24、 for conformance of HiperMAN/WiMAX compliant systems. Although this PICS refers to IEEE 802.16e 5, its scope is currently limited to IEEE 802.16 4 with Corrigendum 1. The items covered by this PICS are also currently restricted to the OFDM + PMP configuration. 2 References References are either spec
25、ific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. Non-specific reference may be made only to a complete document or a part thereof and only in the following cases: - if it is accepted that it
26、 will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. For online re
27、ferenced documents, information sufficient to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the reference should, as far as possible, remain valid for the expected life of the
28、 document. The reference shall include the method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
29、their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendme
30、nts) applies. 1 ETSI TS 102 177: “Broadband Radio Access Networks (BRAN); HiperMAN; Physical (PHY) layer“. 2 ETSI TS 102 178 (V1.2.1): “Broadband Radio Access Networks (BRAN); HiperMAN; Data Link Control (DLC) layer“. 3 ETSI TS 102 210: “Broadband Radio Access Networks (BRAN); HiperMAN; System profi
31、les“. 4 IEEE 802.16-2004: “IEEE Standard for local and metropolitan area networks - Part 16: Air Interface for Fixed Broadband Wireless Access Systems“. 5 IEEE 802.16e-2005: “Standard for Local and metropolitan area networks - Part 16: Air Interface for Fixed and Mobile Broadband Wireless Access Sys
32、tems. Amendment 2: Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands and Corrigendum 1“. 6 ISO/IEC 9646-1/ITU-T Recommendation X.290: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: Gen
33、eral concepts“. ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 7 7 ISO/IEC 9646-7/ITU-T Recommendation X.296: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 8 Void. 9 ETSI EG 201 058: “Methods for Test
34、ing and Specification (MTS); Implementation Conformance Statement (ICS) proforma style guide“. 10 IEEE 802.3: “IEEE Standard for Information Technology - Telecommunications and Information Exchange between Systems - Local and Metropolitan Area Networks - Specific requirements - Part 3: Carrier Sense
35、 Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications“. 11 IEEE 802.1Q: “IEEE Standards for Local and Metropolitan Area Networks - Virtual Bridged Local Area Networks“. 12 ITU-T Recommendation X.690: “Information technology - ASN.1 encoding rules: Specif
36、ication of Basic Encoding Rules (BER), Canonical Encoding Rules (CER) and Distinguished Encoding Rules (DER)“. 13 IETF RFC 2131: “Dynamic Host Configuration Protocol“. 14 IETF RFC 868: “Time Protocol“. 15 IEEE 802.2/ISO/IEC 8802.2 (1998): “IEEE Standard for Information technology - Telecommunication
37、s and Information Exchange Between Systems - Local and Metropolitan Area Networks - Specific Requirements - Part 2: Logical Link Control“. 16 IEEE 802.1D - 2004: “IEEE standard for Local and metropolitan area networks-Media Access Control (MAC) Bridges“. NOTE: Incorporates IEEE 802.1t-2001 and IEEE
38、802.1w. 2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies.
39、 Not applicable. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-1 6, TS 102 177 1, TS 102 178 2, ISO/IEC 9646-1 6 and IEEE 802.16-2004 4 as corrected by Corrigendum 1 of IEEE 802.16e-2005 5 apply. 3.2
40、 Symbols For the purposes of the present document, the following symbols apply: BW Nominal channel bandwidth (MHz) m CID range divider PTX,max Maximum mean transmit power at the antenna port (dBm) bT Useful OFDM symbol time (s) ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 8 FT Frame duration (ms) gT OFDM
41、 symbol guard time or CP time (s) sT OFDM symbol time (s) 3.3 Abbreviations For the purposes of the present document, the abbreviations given in TS 102 177 1, TS 102 178 2, ISO/IEC 9646-1 6 and the following apply: AAS Adaptive Antenna System ARQ Automatic Repeat reQuest BE Best Effort service BER B
42、it Error Rate BPSK Binary Phase Shift Keying BS Base Station BSN Block Sequence Number BW BandWidth CBC Cipher Block Chaining CC Convolutional CodingCID Connection IDentifier CINR Carrier to noise and INterference Ratio CRC Cyclic Redundancy Check DCD Downlink Channel DescriptorDES Data Encryption S
43、tandard DFS Dynamic Frequency SelectionDHCP Dynamic Host Configuration Protocol DIUC Dowlink Interval Usage Code DL DownLink DLFP DownLink Frame Prefix DSA Dynamic Service Addition DSC Dynamic Service Change DSD Dynamic Service DeletionEIRP Effective Isotropic Radiated Power FC Fragmentation Control
44、 FEC Forward Error Correction FPC Fast Power Control FSN Frequence Sequence Number HCS Header Check Sequence HM HiperMANHMAC Hashed Message Authentication Code ID IDentifier IE Information Element IUT Implementation Under Test MAC Medium Access Control MSB Most Significant Bit OFDM Orthogonal Freque
45、ncy Division Multiplexing PDU Protocol Data Unit PHY PHYsical layer PICS Protocol Implementation Conformance Statement PKM Privacy Key Management PMP Point-to-Multipoint QAM Quadrature Amplitude Modulation QPSK Quadrature Phase Shift Keying REQ REQuest RNG RaNGing RS Reed Solomon RSP ReSPonse RSSI R
46、eceived Signal Strength Indicator RTG Receive/Transmit transition Gap rtPS real time Polling Service ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 9 SA Security Association SAID Security Association IDentifier SAP Service Access Point SI Slip Indicator SNMP Simple Network Management Protocol SS Subscriber
47、 Station STC Space Time Coding SUT System Under Test TC Transmission Convergence sublayer TFTP Trivial File Transfer Protocol TLV Type/Length/Value TTG Transmit/receive Transition Gap TX Transmitter UCD Uplink Channel Descriptor UGS Unsolicited Grant Service UL UpLink VLAN Virtual Local Area Network
48、 4 Conformance to this PICS Proforma Specification If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be technically equivalent to the text of the PICS proforma given in annex A, and shall preserve the numbering, naming, and ordering of the
49、proforma items. A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with the guidance for completion given in clause A.1.ETSI ETSI TS 102 385-1 V2.5.1 (2008-12) 10Annex A (normative): Protocol ICS (PICS) for HiperMAN/WiMAX Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PICS proforma in this annex so that it can be used for its intended pu
