1、 ETSI TS 102 442-5 V1.1.1 (2006-11)Technical Specification Satellite Earth Stations and Systems (SES);Satellite Component of UMTS/IMT-2000;Multimedia Broadcast/Multicast Services;Part 5: Performances over the radio InterfaceETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 2 Reference DTS/SES-00250-5 Keywords
2、 broadcast, IMT-2000, performance, satellite, service, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Impo
3、rtant notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is th
4、e Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Info
5、rmation on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No p
6、art may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2006. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the bene
7、fit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 3 Contents Inte
8、llectual Property Rights4 Foreword.4 Introduction 4 1 Scope 6 2 References 6 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .7 4 Performance requirement .7 4.1 General .7 4.2 Demodulation of FACH in static propagation conditions 7 4.2.1 Minimum requirement 7 4.3 Demodulation of
9、 FACH in multi-path fading conditions.8 4.3.1 ITU Models A, B, C8 4.3.1.1 Minimum requirement - LOS8 4.3.1.2 Minimum requirement NLOS 9 4.3.2 Combined satellite and transparent IMR 10 4.3.3 Combined satellite and regenerative IMR 13 4.3.4 IMR only.14 4.3.5 Aeronautical14 4.4 Demodulation of FACH in
10、satellite diversity mode .15 4.4.1 Minimum requirement 15 4.5 Detection of Broadcast Channel (BCH) .16 4.5.1 Minimum requirement 16 4.6 Demodulation of Paging Channel (PCH) .17 4.6.1 Minimum requirement 17 Annex A (normative): Measurement channels19 A.1 General .19 A.2 Downlink reference measurement
11、 channel 19 A.2.1 DL reference measurement channel (8 kbps) .19 A.2.2 DL reference measurement channel (32 kbps) .20 A.2.3 DL reference measurement channel (64 kbps) .21 A.2.4 DL reference measurement channel (128 kbps) .22 A.2.5 DL reference measurement channel (256 kbps) .23 A.2.6 DL reference mea
12、surement channel (384 kbps) .24 A.3 DL reference parameters for PCH tests25 Annex B (normative): Propagation conditions26 B.1 Propagation conditions.26 B.1.1 Static propagation condition.26 B.1.2 Multi-path fading propagation conditions 26 B.1.2.1 Satellite channels 26 B.1.2.2 Combined Satellite and
13、 IMR channels27 Annex C (informative): Bibliography.28 History 29 ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publ
14、icly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI
15、 Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are,
16、or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document is part 5 of a multi-part deliverable covering Satellite Earth Stations and Systems (
17、SES); Satellite Component of UMTS/IMT-2000; Multimedia Broadcast/Multicast Services, as identified below: Part 1: “Services definitions“; Part 2: “Architecture and functional description“; Part 3: “Introduction in the Radio Access Network (RAN)“; Part 4: “Interworking with terrestrial UMTS networks“
18、; Part 5: “Performances over the radio interface“; Part 6: “Security“. Introduction S-UMTS stands for the Satellite component of the Universal Mobile Telecommunication System. S-UMTS systems will complement the terrestrial UMTS (T-UMTS) and inter-work with other IMT-2000 family members through the U
19、MTS core network. S-UMTS will be used to deliver 3rdgeneration mobile satellite services (MSS) utilizing either low (LEO) or medium (MEO) earth orbiting, or geostationary (GEO) satellite(s). S-UMTS systems are based on terrestrial 3GPP specifications and will support access to GSM/UMTS core networks
20、. NOTE 1: The term T-UMTS will be used in the present document to further differentiate the Terrestrial UMTS component. Due to the differences between terrestrial and satellite channel characteristics, some modifications to the terrestrial UMTS (T-UMTS) standards are necessary. Some specifications a
21、re directly applicable, whereas others are applicable with modifications. Similarly, some T-UMTS specifications do not apply, whilst some S-UMTS specifications have no corresponding T-UMTS specification. - Since S-UMTS is derived from T-UMTS, the organization of the S-UMTS specifications closely fol
22、lows the original 3rdGeneration Partnership Project (3GPP) structure. An S-UMTS system is defined by the combination of a family of S-UMTS specifications and 3GPP specifications, as follows: - If an S-UMTS specification exists it takes precedence over the corresponding 3GPP specification (if any). T
23、his precedence rule applies to any references in the corresponding 3GPP specifications. ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 5 NOTE 2: Any references to 3GPP specifications within the S-UMTS specifications are not subject to this precedence rule. For example, an S-UMTS specification may contain s
24、pecific references to the corresponding 3GPP specification. - If an S-UMTS specification does not exist, the corresponding 3GPP specification may or may not apply. The exact applicability of the complete list of 3GPP specifications shall be defined at a later stage. ETSI ETSI TS 102 442-5 V1.1.1 (20
25、06-11) 6 1 Scope The scope of the present document is to establish UE minimum performances for Satellite Multimedia Broadcast/Multicast Service. The present document is applicable to UE that conform to TS 101 851 parts 1 to 3 and to RF characteristics specified in TS 125 101 4. The UE shall meet the
26、 specified performances for all S-MBMS services supported. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version
27、number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While an
28、y hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 1 ETSI TS 101 851-1: “Satellite Earth Stations and Systems (SES); Satellite Component of UMTS/IMT2000; G-family; Part 1: Physical channels and mapping of transport channels into
29、 physical channels (S-UMTS-A 25.211)“. 2 ETSI TS 101 851-2: “Satellite Earth Stations and Systems (SES); Satellite Component of UMTS/IMT2000; G-family; Part 2: Multiplexing and channel coding (S-UMTS-A 25.212)“. 3 ETSI TS 101 851-4: “Satellite Earth Stations and Systems (SES); Satellite Component of
30、 UMTS/IMT2000; G-family; Part 4: Physical layer procedures (S-UMTS-A 25.214)“. 4 ETSI TS 125 101: “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101)“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the
31、present document, the terms and definitions given in 2 and the following apply: Block Error Rate: error rate of the transport (data) blocks passed by the physical layer to MAC layer for a given transport channel (i.e. physical layer error rate) Transmission Time Interval: interval of time over which
32、 a transport block is transmitted; multiple transport blocks may be transmitted in a transmission time interval per transport channel ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 7 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AWGN Additive White Gaussian
33、Noise BCH Broadcast CHannel BER Bit Error Ratio BER Block Error Rate BLER BLock Error Ratio DL DownLink FACH Forward Access CHannel IMR Intermediate Module Repeater LOS Line Of Sight NA Not Applicable NLOS No Line Of Sight PCH Paging Channel P-CPICH Primary-Common PIlot CHannel S-CCPCH Secondary-Com
34、mon Control Physical CHannel S-MBMS Satellite-Multimedia Broadcast/Multicast Service TFCI Transport Format Combination Indicator TFCS Transport Format Combination Set TrCH Transport CHannel TTI Transmission Time Interval UE User Equipment 4 Performance requirement 4.1 General The performance require
35、ments for the UE in this clause are specified for the measurement channels specified in annex A, the propagation conditions specified in annex B. 4.2 Demodulation of FACH in static propagation conditions The receive characteristic of the Forward Access CHannel (FACH) in the static environment is det
36、ermined by the BLock Error Ratio (BLER). BLER is specified for each individual data rate of the FACH. FACH is mapped into the Secondary Common Control Physical CHannel (S-CCPCH). 4.2.1 Minimum requirement For the parameters specified in table 4.1 the average downlink orcIESCCPCH_power ratio shall be
37、 below the specified value for the BLER shown in table 4.7. These requirements are applicable for TFCS size 16. Table 4.1: FACH parameters in static propagation conditions Parameter Unit Test 1 Test 2 Test 3 Test 4 Test 5 Test 6 Phase reference P-CPICH ocorIIdB -1 ocI dBm/3,84 MHz -60 Information Da
38、ta Rate kbps 8 32 64 128 256 384 ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 8 Table 4.2: FACH requirements in static propagation conditions Test Number or c I E SCCPCH _ BLER 1 -19,6 dB 10-2 2 -15,8 dB 10-2 3 -12,8 dB 10-2 4 -10,3 dB 10-2 5 -7,5 dB 10-26 -5,3 dB 10-2 4.3 Demodulation of FACH in multi-p
39、ath fading conditions Demodulation performance requirements are specified in both LOS view of the satellite signal, i.e. in presence of Rice channel at 3 km/h and 250 km/h and NLOS view of the satellite signal, Rayleigh channel at 3 km/h and 50 km/h. 4.3.1 ITU Models A, B, C 4.3.1.1 Minimum requirem
40、ent - LOS For the parameters specified in table 4.3 the average downlink orcIESCCPCH_power ratio shall be below the specified value for the BLER shown in tables 4.4, 4.5 and 4.6. These requirements are applicable for TFCS size 16. Table 4.3: FACH parameters in ITU A, B, C LOS propagation conditions
41、Parameter Unit Test 1 Test 2 Test 3 Test 4 Test 5 Test 6 Phase reference P-CPICH ocorIIdB -3 -3 -3 9 9 9 ocI dBm/3,84 MHz -60 UE speed km/h 3 Information Data Rate kbps 8 32 64 128 256 384 Parameter Unit Test 7 Test 8 Test 9 Test 10 Test 11 Test 12 Phase reference P-CPICH ocorIIdB -3 -3 -3 9 9 9 ocI
42、 dBm/3,84 MHz -60 UE speed Km/h 250 Information Data Rate kbps 8 32 64 128 256 384 Table 4.4: FACH requirements in ITU A LOS propagation conditions Test Number orcIESCCPCH_BLER Test Number orcIESCCPCH_BLER 1 -16,6 dB 10-2 7 -15,4 dB 10-2 2 -12,8 dB 10-2 8 -12,2 dB 10-2 3 -9,8 dB 10-2 9 -9,1 dB 10-2
43、4 -19,5 dB 10-2 10 -18,9 dB 10-2 5 -16,4 dB 10-2 11 -16,1 dB 10-2 6 -14 dB 10-212 -13,6 dB 10-2ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 9 Table 4.5: FACH requirements in ITU B LOS propagation conditions Test Number orcIESCCPCH_BLER Test Number orcIESCCPCH_BLER 1 -16,1 dB 10-2 7 -14,8 dB 10-2 2 -12,3
44、dB 10-2 8 -11,6 dB 10-2 3 -9,3 dB 10-2 9 -8,6 dB 10-2 4 -19,2 dB 10-2 10 -18,4 dB 10-2 5 -15,8 dB 10-2 11 -15,7 dB 10-2 6 -13,3 dB 10-212 -13,1 dB 10-2Table 4.6: FACH requirements in ITU C LOS propagation conditions Test Number orcIESCCPCH_BLER Test Number orcIESCCPCH_BLER 1 -14,8 dB 10-2 7 -13 dB 1
45、0-2 2 -11 dB 10-2 8 -10,1 dB 10-2 3 -8 dB 10-2 9 -7,2 dB 10-2 4 -18,2 dB 10-2 10 -17,3 dB 10-2 5 -14,1 dB 10-2 11 -14,3 dB 10-2 6 -11 dB 10-212 -11 dB 10-24.3.1.2 Minimum requirement NLOS For the parameters specified in table 4.7 the average downlink orcIESCCPCH_power ratio shall be below the specif
46、ied value for the BLER shown in tables 4.8, 4.9 and 4.10. These requirements are applicable for TFCS size 16. Table 4.7: FACH parameters in ITU A NLOS propagation conditions Parameter Unit Test 1 Test 2 Test 3 Test 4 Test 5 Test 6 Phase reference P-CPICH ocorIIdB 9 ocI dBm/3,84 MHz -60 UE speed Km/h
47、 3 Information Data Rate kbps 8 32 64 128 256 384 Parameter Unit Test 7 Test 8 Test 9 Test 10 Test 11 Test 12 Phase reference P-CPICH ocorIIdB 9 ocI dBm/3,84 MHz -60 UE speed Km/h 50 Information Data Rate kbps 8 32 64 128 256 384 Table 4.8: FACH requirements in ITU A NLOS propagation conditions Test
48、 Number orcIESCCPCH_BLER Test Number orcIESCCPCH_BLER 1 -15,8 dB 10-2 7 -24,3 dB 10-2 2 -11,4 dB 10-2 8 -19,7 dB 10-2 3 -8 dB 10-2 9 -16,7 dB 10-2 4 -10,5 dB 10-2 10 -17,8 dB 10-2 5 -1,6 dB 10-2 11 -12 dB 10-2 6 NA 10-212 -6,5 dB 10-2ETSI ETSI TS 102 442-5 V1.1.1 (2006-11) 10Table 4.9: FACH requirem
49、ents in ITU B NLOS propagation conditions Test Number orcIESCCPCH_BLER Test Number orcIESCCPCH_BLER 1 -17,2 dB 10-2 7 -24,6 dB 10-2 2 -12,7 dB 10-2 8 -20,1 dB 10-2 3 -9,3 dB 10-2 9 -17,1 dB 10-2 4 -11,3 dB 10-2 10 -17,8 dB 10-2 5 -3,1 dB 10-2 11 -9,8 dB 10-2 6 -0,4 dB 10-212 -7,1 dB 10-2Table 4.10: FACH requirements in ITU C NLOS propagation conditions Test Number orcIESCCPCH_BLER Test Number orcIESCCPCH_BLER 1 -18 dB 10-2 7 -24 dB 10-2 2 -13,7 dB 10-2 8 -19,7 dB 10-2 3 -10,1 dB 10-2 9 -16,5 dB 10-2 4 -11,3 dB 10-2 10 -16,4 dB 10-2 5 -5,1 dB 10-2
