1、 ETSI TS 102 516 V1.2.1 (2007-04)Technical Specification Methods for Testing and Specification (MTS);Internet Protocol Testing (IPT): IPv6 Core Protocol;Conformance Abstract Test Suite (ATS) and partial ProtocolImplementation eXtra Information for Testing (PIXIT) proformafloppy3 ETSI ETSI TS 102 516
2、 V1.2.1 (2007-04) 2 Reference RTS/MTS-IPT-0062-IPv6-CorATS Keywords IP, IPv6, testing, TTCN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfectu
3、re de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versi
4、ons, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to re
5、vision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support
6、.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2007. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks
7、 of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 516 V1
8、.2.1 (2007-04) 3 Contents Intellectual Property Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .7 4 Abstract Test Method (ATM).7 4.1 Configuration cfCore018 4.2 Configuration cfCore028 4.3 Configuration cfCore038 5 Untestable and not
9、implemented Test Purposes (TP).9 5.1 Untestable TP .9 5.2 Not implemented TP 10 6 ATS conventions10 7 PCTR conformance 11 8 PIXIT conformance11 9 ATS Conformance11 Annex A (normative): Abstract Test Suite (ATS) .12 A.1 The ATS in TTCN-3 core (text) format .12 Annex B (normative): Partial PIXIT profo
10、rma 13 B.1 Identification summary.13 B.2 ATS summary 13 B.3 Test laboratory13 B.4 Client identification14 B.5 SUT 14 B.6 Protocol layer information14 B.6.1 Protocol identification 14 B.6.2 Generic Setup .15 B.6.3 Default Values15 B.6.4 Unknown IDs .15 B.6.5 Mac Layer 16 B.6.6 Addresses .16 B.6.6.1 P
11、refixes .16 B.6.6.2 IUT Addresses 16 B.6.6.3 Tester Addresses.17 B.6.6.3.1 Host 1 (HS_01) .17 B.6.6.3.2 Host 2 (HS_02) .17 B.6.6.3.3 Host 3 (HS_03) .17 B.6.6.3.4 Router 1 (RT_01)18 B.6.6.3.5 Router 3 (RT_03)18 B.6.7 Timer 18 Annex C (normative): PCTR proforma .19 ETSI ETSI TS 102 516 V1.2.1 (2007-04
12、) 4 C.1 Identification summary.19 C.1.1 Protocol conformance test report19 C.1.2 IUT identification.19 C.1.3 Testing environment.20 C.1.4 Limits and reservation20 C.1.5 Comments.20 C.2 IUT Conformance status 21 C.3 Static conformance summary .21 C.4 Dynamic conformance summary21 C.5 Static conforman
13、ce review report.21 C.6 Test campaign report22 C.7 Void28 C.8 Observations.28 Annex D (informative): Bibiography29 History 30 ETSI ETSI TS 102 516 V1.2.1 (2007-04) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The infor
14、mation pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the
15、ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 0
16、00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Methods for Testing and Specification (MTS). ETSI ETSI TS 102 516 V1.2.1 (2007-04) 6 1 Scope
17、 The present document specifies the Abstract Test Suite (ATS) for the core functions of the Internet Protocol, version 6, as defined in the specifications 11 through to 12. The ATS is based on the requirements defined in the IPv6 requirements catalogue (TS 102 514 2) and the IPv6 test purposes (TS 1
18、02 515 3) and written according to the guidelines of TS 102 514 2, ISO/IEC 9646-2 5 and ETS 300 406 9. The objective of the present document is to provide a basis for conformance tests for IPv6 equipment giving a high probability of inter-operability between different manufacturers IPv6 equipments.
19、Annex A provides the Tree and Tabular Combined Notation (TTCN-3) part of the ATS. Annex B provides the Partial Protocol Implementation Extra Information for Testing (PIXIT) Proforma of the ATS. Annex C provides the Protocol Conformance Test Report (PCTR) Proforma of the ATS. 2 References The followi
20、ng documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not appl
21、y. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI can
22、not guarantee their long term validity. 1 ETSI TS 102 351: “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT); IPv6 Testing: Methodology and Framework“. 2 ETSI TS 102 514: “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT): IPv6 Core Protocol; Re
23、quirements Catalogue“. 3 ETSI TS 102 515: “Methods for Testing and Specification (MTS); Internet Protocol Testing (IPT): IPv6 Core Protocol; Conformance Test Suite Structure and Test Purposes (TSS Protocol and profile conformance testing specifications; Standardization methodology“. ETSI ETSI TS 102
24、 516 V1.2.1 (2007-04) 7 10 ETSI ES 201 873-1: “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 1: TTCN-3 Core Language“. 11 IETF RFC 1981: “Path MTU Discovery for IP version 6“. 12 IETF RFC 3513: “Internet Protocol Version 6 (IPv6) addressing Archit
25、ecture“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: abstract test case: Refer to ISO/IEC 9646-1 4. Abstract Test Method (ATM): Refer to ISO/IEC 9646-1 4. Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 4. Im
26、plementation Under Test (IUT): Refer to ISO/IEC 9646-1 4. Lower Tester (LT): Refer to ISO/IEC 9646-1 4. Test Purpose (TP): Refer to ISO/IEC 9646-1 4. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ATM Abstract Test Method ATS Abstract Test Suite ETS Ex
27、ecutable Test Suite IETF Internet Engineering Task Force IPv6 Internet Protocol version 6 IUT Implementation Under Test MAC Medium Access Control MOT Means Of Testing PCO Point of Control and Observation PCTR Protocol Conformance Test Report PICS Protocol Implementation Conformance Statement PIXIT P
28、rotocol Implementation eXtra Information for Testing PTC Parallel Test Component SUT System Under Test TC Test Case TP Test Purpose TSS Test Suite Structure 4 Abstract Test Method (ATM) This clause describes the ATM used to test the IPv6 core functions as defined in the RFC specifications 11 through
29、 to 12. The three following configurations have been developed to test the two different types of IUT, hosts and routers. Either a simple one-to-one connection between tester and IUT is established which serves as Point of Control and Observation (PCO) or the IUT is connected to two Parallel Test Co
30、mponents (PTCs) that act as router or host respectively. ETSI ETSI TS 102 516 V1.2.1 (2007-04) 8 4.1 Configuration cfCore01 Figure 1 shows the configuration cfCore01. This is the basic configuration for router or host tests. PTC01 simulates a router. NUT RT01 Net A Test System PTC01 HS01 Figure 1: c
31、fCore01 4.2 Configuration cfCore02 Figure 2 shows cfCore02. The IUT is a router. PTC01 and PTC02 simulate hosts. CfCore02_Hs01 is used in the case where only 1 interface of the IUT is tested. PTC01 HS01 IUT PTC02 HS02 Net A Net B Test System CF02_HS01 Figure 2: cfCore02 4.3 Configuration cfCore03 Fi
32、gure 3 shows cfCore03. The IUT is a host. PTC01 and PTC02 simulate routers. At start time of a test case PTC1 RT01 is considered to be the default router of the host acting as IUT. CfCore03_Rt01 shall be used in the case where only the interface between RT01 and the IUT is tested. ETSI ETSI TS 102 5
33、16 V1.2.1 (2007-04) 9 Net A Test System RT01 Net B HS02 PTC01 RT03 Net C HS03 PTC02 HUT Figure 3: cfCore03 5 Untestable and not implemented Test Purposes (TP) The ATS is comprised of 271 TC. Those were derived from a total of 396 TP. 5.1 Untestable TP This clause gives a list of 80 TP, which are not
34、 implemented in the ATS due to the chosen ATM or other restrictions: TP_COR_1092_01, TP_COR_1089_01, TP_COR_1034_01, TP_COR_1008_01, TP_COR_1814_01, TP_COR_1086_01, TP_COR_1122_01, TP_COR_9012_01, TP_COR_1272_01, TP_COR_9016_01, TP_COR_9017_01, TP_COR_9018_01, TP_COR_9019_01, TP_COR_8009_01, TP_COR_
35、1225_01, TP_COR_1276_01, TP_COR_1282_01, TP_COR_1282_02, TP_COR_1256_01, TP_COR_1263_01, TP_COR_1250_01, TP_COR_1292_01, TP_COR_1471_01, TP_COR_1472_01, TP_COR_1416_01, TP_COR_1416_02, TP_COR_1416_03, TP_COR_1416_04, TP_COR_1458_01, TP_COR_1448_01, TP_COR_1444_01, TP_COR_1442_01, TP_COR_8579_01, TP_
36、COR_8492_01, TP_COR_8493_01, TP_COR_8232_01, TP_COR_8583_01, TP_COR_8387_01, TP_COR_8402_01, TP_COR_8586_01, TP_COR_8210_01, TP_COR_8246_01, TP_COR_8160_01, TP_COR_8169_01, TP_COR_8168_01, TP_COR_8805_01, TP_COR_8338_02, TP_COR_8338_03, TP_COR_8338_05, TP_COR_8338_06, TP_COR_8108_01, TP_COR_1294_01,
37、 TP_COR_1245_01, TP_COR_1248_01, TP_COR_1299_01, TP_COR_9027_01, TP_COR_1304_01, TP_COR_1306_01, TP_COR_1315_01, TP_COR_8578_01, TP_COR_8560_01, TP_COR_8530_01, TP_COR_8125_01, TP_COR_8126_01, TP_COR_8128_01, TP_COR_8243_01, TP_COR_8133_01, TP_COR_8379_01, TP_COR_8384_01, TP_COR_8382_01, TP_COR_1435
38、_01, TP_COR_8577_01, TP_COR_8435_01, TP_COR_8512_01, TP_COR_8516_01, TP_COR_8235_01, TP_COR_8574_01, TP_COR_8326_01, TP_COR_8297_01, TP_COR_8188_01. ETSI ETSI TS 102 516 V1.2.1 (2007-04) 105.2 Not implemented TP A number of 44 TP have not been implemented, as the dynamic behaviour that validates the
39、ir test purpose is already implemented in one or more TC. Table 1 gives the relation between the non-implemented TP and the TC that cover(s) its purpose. Table 1: List of not implemented TP TP not implemented TC that covers the dynamic behaviour TP_COR_8814_01 TC_COR_8813_01 TP_COR_1455_01 TC_COR_10
40、85_01 TP_COR_8013_01 TC_COR_1225_01 TP_COR_1244_01 TC_COR_1235_01 TP_COR_1239_01 TC_COR_1210_02 TP_COR_8148_01 TC_COR_1280_01 TP_COR_1257_01 TC_COR_1280_01 TP_COR_1419_01 TC_COR_1417_01 TP_COR_1459_01 TC_COR_1468_01 TP_COR_1453_01 TC_COR_1085_01 TP_COR_1453_02 TC_COR_1011_01 TP_COR_1453_03 TC_COR_10
41、20_01 TP_COR_1447_01 TC_COR_1058_01 TP_COR_1447_02 TC_COR_1058_02 TP_COR_8415_01 TC_COR_8146_01 TP_COR_8483_01 TC_COR_8482_01 TP_COR_8491_01 TC_COR_8146_01 TP_COR_8494_01 TC_COR_8464_01 TP_COR_8499_01 TC_COR_8147_01 TP_COR_8504_01 TC_COR_8434_01 TP_COR_8511_01 TC_COR_8434_01, TC_COR_8504_01 TP_COR_8
42、366_01 TC_COR_8507_01 TP_COR_8565_01 TC_COR_8396_01 TP_COR_8162_01 TC_COR_8159_01, TC_COR_8179_01, TC_COR_8180_01 TP_COR_8444_01 TC_COR_8179_01 TP_COR_8452_01 TC_COR_8159_01 TP_COR_8171_01 TC_COR_8461_01 TP_COR_8172_01 TC_COR_8470_01 TP_COR_8410_01 TC_COR_8567_01 TP_COR_8587_01 TC_COR_8592_01 TP_COR
43、_8118_01 TC_COR_8513_01 TP_COR_8113_01 TC_COR_8146_01 TP_COR_8149_01 TC_COR_8146_01 TP_COR_1228_01 Several TC test the behaviour implicitly TP_COR_1303_01 TC_COR_1298_01 TP_COR_8343_01 TC_COR_8349_01 TP_COR_1042_01 TC_COR_1443_01 TP_COR_8107_01 Several TC test the behaviour implicitly TP_COR_1419_03
44、 TC_COR_1417_02 TP_COR_8330_01 TC_COR_8586_01 TP_COR_8299_01 TC_COR_9034_01 TP_COR_8315_01 TC_COR_9034_02 TP_COR_8315_02 TC_COR_9034_01 TP_COR_8550_01 TC_COR_8183_01 6 ATS conventions The complete description of the ATS conventions is found in TS 102 5141 1. ETSI ETSI TS 102 516 V1.2.1 (2007-04) 117
45、 PCTR conformance A test laboratory, when requested by a client to produce a PCTR, is required, as specified in ISO/IEC 9646-5 7, to produce a PCTR conformant with the PCTR template given in annex B of ISO/IEC 9646-5 7. Furthermore, a test laboratory, offering testing for the ATS specification conta
46、ined in annex C, when requested by a client to produce a PCTR, is required to produce a PCTR conformant with the PCTR proforma contained in annex A. A PCTR which conforms to this PCTR proforma specification shall preserve the content and ordering of the clauses contained in annex A. Clause A.6 of th
47、e PCTR may contain additional columns. If included, these shall be placed to the right of the existing columns. Text in italics may be retained by the test laboratory. 8 PIXIT conformance A test realizer, producing an executable test suite for the Abstract Test Suite (ATS) specification contained in
48、 annex C, is required, as specified in ISO/IEC 9646-4 6, to produce an augmented partial PIXIT proforma conformant with this partial PIXIT proforma specification. An augmented partial PIXIT proforma which conforms to this partial PIXIT proforma specification shall, as a minimum, have contents which
49、are technically equivalent to annex B. The augmented partial PIXIT proforma may contain additional questions that need to be answered in order to prepare the Means Of Testing (MOT) for a particular Implementation Under Test (IUT). A test laboratory, offering testing for the ATS specification contained in annex C, is required, as specified in ISO/IEC 9646-5 7, to further augment the augmented partial PIXIT proforma to produce a PIXIT proforma conformant with this partial PIXIT proforma specification. A PIXIT proforma w
