1、 ETSI TS 102 545-2 V1.1.1 (2007-09)Technical Specification Broadband Radio Access Networks (BRAN);HiperMAN;Conformance Testing for WiMAX/HiperMAN 1.3.1;Part 2: Test Suite Structure and Test Purposes (TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which
2、is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not r
3、eferenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Broadband Radio Access Networks (BRAN). The present document is part 2
4、 of a multi-part deliverable. Full details of the entire series can be found in TS 102 178 1. ETSI ETSI TS 102 545-2 V1.1.1 (2007-09) 9 1 Scope The present document contains the Test Suite Structure (TSS) and Test Purposes (TP) to test the BRAN HiperMAN Data Link Control (DLC) layer. The objective o
5、f this test specification is to provide a basis for conformance tests for HiperMAN equipment giving a high probability of air interface inter-operability between different manufacturers“ HiperMAN equipment. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 5 and ISO/IEC 964
6、6-2 6) as well as the ETSI rules for conformance testing (ETS 300 406 4) are used as a basis for the test methodology. 2 References The following documents contain provisions that, through reference in this text, constitute provisions of the present document. References are either specific (identifi
7、ed by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might
8、be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this Clause were valid at the time of publication ETSI cannot guarantee their long term validity. 1 ETSI TS 102 178 (V1.3.1): “Broadband Radio Access Networks (BRAN); HiperMAN; Data Link Control (DLC) Layer“. 2 IEEE
9、P802.16 (2004): “Draft IEEE Standard for Local and Metropolitan Area Networks - Part 16: Air Interface for Fixed Broadband Wireless Access Systems“. 3 IEEE 802.16e-2005 and IEEE 802.16-2004/Cor 1-2005: “Standard for Local and metropolitan area networks - Part 16: Air Interface for Fixed and Mobile B
10、roadband Wireless Access Systems. Amendment 2: Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands and Corrigendum 1“. 4 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardiz
11、ation methodology“. 5 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. (See also ITU-T Recommendation X.290 (1991). 6 ISO/IEC 9646-2 (1994): “Information technology - Open Systems Interconnectio
12、n - Conformance testing methodology and framework - Part 2: Abstract Test Suite specification“. (See also ITU-T Recommendation X.291 (1991). 7 ISO/IEC 9646-6 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 6: Protocol profile test
13、 specification“. 8 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 9 IEEE 802.3: “IEEE Standard for Information technology-Telecommunications and information exchange betwe
14、en systems-Local and metropolitan area networks-Specific requirements Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications“. ETSI ETSI TS 102 545-2 V1.1.1 (2007-09) 1010 ISO 3166: “Codes for the representation of names of countries
15、and their subdivisions“. 11 ETSI TS 102 545-1: “ Broadband Radio Access Networks (BRAN); HiperMAN; Conformance Testing for WiMAX/HiperMAN 1.3.1; Part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the pr
16、esent document, the terms and definitions given in ISO/IEC 9646-7 8, TS 102 178 1, IEEE P802.16 2 and IEEE 802.16e 3 apply. 3.2 Abbreviations For the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 5, ISO/IEC 9646-6 7, ISO/IEC 9646-7 8, TS 102 178 1, IEEE 802.16 2 IEEE
17、802.16e 3 and the following, apply: AAS Adaptive Antenna System ACK ACKnowledgment AES Advanced Encryption Standard AK Authorization Key ARQ Automatic Repeat reQuest ATM Asynchronous Transfer Mode AUTH AUTHentication/AUTHorizationBE Best Effort BI Invalid Behaviour BO inOpportune Behaviour BPSK Bina
18、ry Phase Shift Keying BS Base Station BSN Block Sequence Number BV Valid Behaviour BW BandWidth BWA BandWidth Allocation and Polling CAT PDU Concatenation CBC Cipher Block Chaining CC Chase Combining CCC Clock Comparison CD Channel Descriptors CDC Channel Descriptor Change CDM Channel Descriptors an
19、d Maps CDS Classifier DSx Signalling CERT CertificatesCID Connection IDentifier CINR Carrier to noise and INterference Ratio CLS CLaSsification CRC Cyclic Redundancy Check CS Convergence Sublayer DBPC Downlink Burst Profile Change Request DCD Downlink Channel Descriptor DEC DecryptionDES Data Encryp
20、tion Standard DIUC Downlink Interval Usage Code DL DownLink DLC Data Link Control layer DS Dynamic Services DSA Dynamic Service Addition DSC Dynamic Service Change ETSI ETSI TS 102 545-2 V1.1.1 (2007-09) 11DSD Dynamic Service Deletion DSx Dynamic Service addition, change or deletion ECB Electronic C
21、ontrol Block EKS Encryption and Key Scheduling ENC Encryption ENET Ethernet FC Frame Count FDD Frequency Division Duplexing FPC Fast Power Control FRAG Fragmentation FSM Finite State Machine FWA Fixed Wireless Access HARQ Hybrid Automatic Repeat Request HMAC Hashed Message Authentication Code HT Hea
22、der Type IE Information Element INI Registration, IP Connectivity, and Parameter Transfer INIT Initialization IP IPv4 and IPv6 IPC IP ConnectivityIRNG Initial Ranging IUT Implementation Under Test KEK Key Encryption Key KU Key Usage LRP To a Less Robust Profile MAC Medium Access Control MAP Map and
23、Frame Structure MCP Multicast Polling MRP To a More Robust Profile NACK Negative ACKnowledgmentOFDM Orthogonal Frequency Division Multiplexing OFDMA Orthogonal Frequency Division Multiple Access OPN Operation PACK PackingPCS Packet CS PDU Protocol Data Unit PHS Payload Header Suppression PKM Privacy
24、 and Key Management PMP Point-to-MultiPoint PRNG Periodic Ranging QoS Quality of Service QPS QoS Parameter Sets RE Reset REG Registration REQ REQuest RER Reset and Re-registration RLC Radio Link Control RLV Relevance RNG RaNGing RSP ReSPonse RXD Receive Data SA Security Association SAID Security Ass
25、ociation IDentity SAM Security Association Management SAP Service Access Point SBC Negotiate Basic Capabilities SDU Service Data Unit SET Setup SF Service Flow SS Subscriber Station TDD Time Division Duplexing TEK Encryption Key Transfer ETSI ETSI TS 102 545-2 V1.1.1 (2007-09) 12TFTP Trivial File Tr
26、ansfer Protocol TI Timer and counter TLV Type, Length, Value TP Test Purposes TSS Test Suite Structure TXD Transmit Data UCD Uplink Channel Descriptor UGS Unsolicited Grant Service UL Uplink VLAN Virtual Local Area Network 4 Test Suite Structure (TSS) 4.1 Structure Figure 1 shows the DLC Test Suite
27、Structure (TSS) including its subgroups defined for conformance testing. Group Function Sub-functionCS options: Encapsulation Ipv46Ipv4 with ROHC / ECRTP Ipv6 with ROHC / ECRTP Ethernet Ipv4 over Ethernet Ipv6 over Ethernet CS options: Classification Classifier DSx Signalling Ipv4 Classification Gen
28、eral Ipv4 classification Ipv4 classification with ROHC Ipv4 classification with ECRTP Ipv6 Classification General Ipv6 classification Ipv6 classification with ROHC Ipv6 classification with ECRTP Ethernet classification Pure Ethernet classification Ipv4 over Ethernet Ipv6 over Ethernet Payload Header
29、 Suppression MAC PDU Formats PDU concatenation Fragmentation Packing CRC ARQ Receiver operations Transmitt operationsReset Radio Link Control (Initial Network Entry and MAC Support of PHY layer) Initial Ranging Periodic Ranging Downlink Burst Profile Management To a Less Robust Profile To a More Rob
30、ust Profile Negotiate Basic Capabilities ETSI ETSI TS 102 545-2 V1.1.1 (2007-09) 13Group Function Sub-function Feedback mechanism MAC support for H-ARQ Support of different MAP IEs TBD list of functions in terms of DL-MAP IEs and UL-MAP IEs; MAP Relevance Registration, IP connectivity and TFTP Regis
31、tration IP ConnectivityDynamic Services (Service flow management) Service Addition Serv Change Service Deletion QoS Parameter Sets Bandwidth Allocation and Polling CDMA Bandwidth Request Request/Grant mechanism Multicast polling General Handover functionality Network topology acquisition Network Adv
32、ertisement Scanning Association HO initiation Initiated by MSInitia by BS Network Re-Entry Acquisition of DL and UL parameters HO Ranging Capabilities Exchange EAP based Authentication/ Authorization Registration HO optimization Sleep mode General functions Power saving class type 1 Power saving cla
33、ss type 2 Power saving class type 3 Periodic ranging during Sleep Mode Idle mode Transition to Idle Mode PagingNetwork Re-entry after Idle Mode Expedited Network Re-entry after Idle Mode Location Update Multicast traffic connections Supported cryptographic suites No data encryption, no data authenti
34、cation e.g. DS1 and DS3. ETSI ETSI TS 102 545-2 V1.1.1 (2007-09) 174.2.2 Main test types The main test types are the valid behaviour group, the invalid behaviour group and the inopportune behaviour group. 4.2.2.1 Valid Behaviour (BV) tests This test group shall verify that the IUT reacts in conformi
35、ty with the base specifications after receipt or exchange of valid Protocol Data Units (PDUs). Valid PDUs means that the exchange of messages and the content of the exchanged messages are considered as valid. 4.2.2.2 Invalid Behaviour (BI) tests This test sub group shall verify that the IUT reacts i
36、n conformity with the TS after receipt of a syntactically invalid PDU. 4.2.2.3 Inopportune Behaviour (BO) tests This test sub group shall verify that the IUT reacts in conformity with the TS after receipt of a syntactically correct PDU not expected in the actual message exchange. 4.2.2.4 Timer and c
37、ounter (TI) tests This test group shall verify that the IUT reacts in conformity with the TS after expiry of a defined timer or counter. 5 Test Purposes (TP) 5.1 Introduction 5.1.1 TP definition conventions The TPs are defined by the rules shown in table 1. Table 1: TP definition rules TP Definition
38、 Item Item Description TP Id The TP Id is a unique identifier formed according to the TP naming conventions defined in the Clause below. P802.16e Reference A pointer to the base specification requirement from which the TP is derived (specification reference, Clause, and paragraph). PICS Item The PIC
39、S item(s) associated with this TP. Initial Condition The IUTs state to which the TP is applied. Expected behaviour Definition of the events that are expected from the IUT pursuant to the base specification given a certain stimulus. Notes Additional optional information provided to the TP reader. ETS
40、I ETSI TS 102 545-2 V1.1.1 (2007-09) 185.1.2 TP Identifier naming conventions The identifier of the TP is built according to table 2. Table 2: TP naming convention Identifier: TP/-H = side type BS Base Station SS Subscriber Station (Mobile Station) = protocol group CSOE CS Options: Encapsulation CSO
41、C CS Options: Classification PHS Payload Header Suppression MAC MAC PDU Formats ARQ ARQ RLC Radio Link Control INI Registration, IP Connectivity, and Parameter Transfer DS Dynamic Services BWA Bandwidth Allocation and Polling GHF General Handover Functionality SLM Sleep Mode IDM Idle Mode MTC Multic
42、ast Traffic Connections SCS Supported Cryptographic Suites PKM Privacy and Key Management version 1 SEC Security version 2 CDM Channel Descriptors and Maps MBS Multicast and Broadcast Services AAS Adaptive Antenna Support RER Reset and Re-registration CCC Clock Comparison = function group IP4 IP ver
43、sion 4 IP6 IP version 6 IP4R IP version 4 with ROHC/ECRTP IP6R IP version 6 with ROHC/ECRTP ENET Ethernet IP4oE IP version 4 over Ethernet IP6oE IP version 6 over Ethernet CDS Classifier DSx Signalling IP4C IP version 4 Classification IP6C IP version Classification ENTC Ethernet Classification CAT P
44、DU Concatenation FRAG Fragmentation PACK Packing CRC Cyclic Redundancy Check RxD Receiver Operations TxD Transmitter Operations RE Reset ACQ Acquisition of DL and UL parameters IRNG Initial Ranging PRNG Periodic Ranging DBPC Downlink Burst Profile Management SBC Negotiate Basic Capabilities FBK Feed
45、back mechanism HARQ MAC support for H-ARQ MPIE Support of different MAP IEs REG Registration IPC IP ConnectivityDSA Dynamic Service Addition DSC Dynamic Service Change DSD Dynamic Service Deletion QPS QoS Parameter Sets CBR CDMA Bandwidth Request REQ Request/Grant ETSI ETSI TS 102 545-2 V1.1.1 (2007
46、-09) 19Identifier: TP/-H MCP Multicast Polling NTA Network Topology acquisition HOI Handover initiation NWR Network Re-entry HOO Handover Optimization GF General Functions PW1 Power Saving class type 1 PW2 Power Saving class type 2 PW3 Power Saving class type 3 PRSM Periodic Ranging during Sleep Mod
47、e TIDM Transition to Idle Mode PG Paging NWRI Network Re-entry after Idle Mode ENWR Expedited Network Re-entry after Idle Mode LOC Location update DES No data encryption, no data authentication IP Type of Service/DSCP; IP Protocol; IP Masked Source Address; IP Destination Address; IP Protocol Source
48、 Port; and IP Protocol Destination Port; the IUT transmits CS SDUs matching the common: IP Protocol Destination Port; IP Type of Service/DSCP; IP Protocol; IP Masked Source Address; IP Destination Address; IP Protocol Source Port; and IP Protocol Destination Port; on the connection having the higher
49、 classifier priority. Test strategy Notes IP service flows can either be IPv4 or IPv6 5.2.2.3 IPv6 classification (IP6C) The same TPs as for IP v4 classification applies replacing IPv4 service flows with IPv6 service flows. 5.2.2.4 Ethernet classification (ENTC) 5.2.2.4.1 Pure Ethernet Classification (PETC) TP ID TP/BS/CSOC/ENTC/PETC/BV-H000 P802.16 Reference Clause 5.2.2, paragraph 3 PICS Item Initial Condition IUT is operational and two DL Ethernet CS service flows are established having different CIDs. Packet c
