1、 ETSI TS 102 545-2 V1.3.1 (2009-06)Technical Specification Broadband Radio Access Networks (BRAN);HiperMAN;Conformance Testing for WiMAX/HiperMAN 1.3.1;Part 2: Test Suite Structure and Test Purposes (TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which
2、is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not r
3、eferenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Broadband Radio Access Networks (BRAN). The present document is part 2
4、 of a multi-part deliverable covering Broadband Radio Access Networks (BRAN); HiperMAN; Conformance Testing for WiMAX/HiperMAN 1.3.1, as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract T
5、est Suite (ATS)“. ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 9 1 Scope The present document contains the Test Suite Structure (TSS) and Test Purposes (TP) to test the BRAN HiperMAN Data Link Control (DLC) layer. The objective of the present document is to provide a basis for conformance tests for Hiper
6、MAN equipment giving a high probability of air interface inter-operability between different manufacturers HiperMAN equipment. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 5 and ISO/IEC 9646-2 6) as well as the ETSI rules for conformance testing (ETS 300 406 4) are use
7、d as a basis for the test methodology. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. Non-specific reference may be made only to a complete document
8、or a part thereof and only in the following cases: - if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which are not found to be publicly available in the expe
9、cted location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application
10、of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. 1 ETSI TS 102 178 (V1.3.1): “Broadband Radio Access Networks (BRAN); HiperMAN; Data Link Control (DLC) Layer“.
11、 2 IEEE P802.16 (2004): “Standard for Local and Metropolitan Area Networks - Part 16: Air Interface for Fixed Broadband Wireless Access Systems“. 3 IEEE 802.16e-2005 and IEEE 802.16-2004/Cor 1-2005: “IEEE Standard for Local and Metropolitan Area Networks - Part 16: Air Interface for Fixed and Mobile
12、 Broadband Wireless Access Systems. Amendment for Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands“. 4 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodolo
13、gy“. 5 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. (See also ITU-T Recommendation X.290 (1991). 6 ISO/IEC 9646-2 (1994): “Information technology - Open Systems Interconnection - Conformance
14、 testing methodology and framework - Part 2: Abstract Test Suite specification“. (See also ITU-T Recommendation X.291 (1991). ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 107 ISO/IEC 9646-6 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Pa
15、rt 6: Protocol profile test specification“. 8 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 9 IEEE 802.3: “IEEE Standard for Information technology-Telecommunications and
16、 information exchange between systems-Local and metropolitan area networks-Specific requirements Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications“. 10 ISO 3166: “Codes for the representation of names of countries and their subdi
17、visions“. 11 ETSI TS 102 545-1: “Broadband Radio Access Networks (BRAN); HiperMAN; Conformance Testing for WiMAX/HiperMAN 1.3.1; Part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 12 IEEE 802.16-Rev2/D7 (October 2008): “Standard for Local and metropolitan area networks Part 16:
18、Air Interface for Broadband Wireless Access Systems“. 2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the reference
19、d document (including any amendments) applies. Not applicable. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-7 8, TS 102 178 1, IEEE P802.16-2004 2 and IEEE 802.16e-2005 3 apply. 3.2 Abbreviations For the pur
20、poses of the present document, the abbreviations given in ISO/IEC 9646-1 5, ISO/IEC 9646-6 7, ISO/IEC 9646-7 8, TS 102 178 1, IEEE P802.16-2004 2, IEEE 802.16e-2005 3 and the following apply: AAS Adaptive Antenna System ACK ACKnowledgment AES Advanced Encryption Standard AK Authorization Key ARQ Aut
21、omatic Repeat reQuest ATM Asynchronous Transfer Mode AUTH AUTHentication/AUTHorizationBE Best Effort BI Invalid Behaviour BO inOpportune Behaviour BPSK Binary Phase Shift Keying BS Base Station BSN Block Sequence Number BV Valid Behaviour BW BandWidth CBC Cipher Block Chaining CC Chase Combining CD
22、Channel Descriptors ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 11CDC Channel Descriptor Change CDM Channel Descriptors and Maps CDS Classifier DSx Signalling CERT CertificatesCID Connection IDentifier CINR Carrier to noise and INterference Ratio CRC Cyclic Redundancy Check CS Convergence Sublayer DBPC
23、Downlink Burst Profile Change Request DCD Downlink Channel Descriptor DEC DecryptionDES Data Encryption Standard DIUC Downlink Interval Usage Code DL DownLink DLC Data Link Control layer DS Dynamic Services DSA Dynamic Service Addition DSC Dynamic Service Change DSD Dynamic Service DeletionDSx Dynam
24、ic Service addition, change or deletion ECB Electronic Control Block EKS Encryption and Key Scheduling ENC Encryption ENET Ethernet FC Frame Count FDD Frequency Division Duplexing FPC Fast Power Control FRAG Fragmentation FSM Finite State Machine FWA Fixed Wireless Access HARQ Hybrid Automatic Repea
25、t Request HMAC Hashed Message Authentication Code HT Header Type IE Information Element INI Registration, IP Connectivity, and Parameter Transfer INIT Initialization IP IPv4 and IPv6 IPC IP ConnectivityIRNG Initial Ranging IUT Implementation Under Test KEK Key Encryption Key KU Key Usage LRP To a Le
26、ss Robust Profile MAC Medium Access Control MAP Map and Frame Structure MCP Multicast Polling MRP To a More Robust Profile NACK Negative ACKnowledgmentOFDM Orthogonal Frequency Division Multiplexing OFDMA Orthogonal Frequency Division Multiple Access OPN Operation PACK PackingPDU Protocol Data Unit
27、PHS Payload Header Suppression PKM Privacy and Key Management PMP Point-to-MultiPoint PRNG Periodic Ranging QoS Quality of Service QPS QoS Parameter Sets RE Reset REG REGistration REQ REQuest ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 12RER Reset and Re-registration RLC Radio Link Control RLV Relevance
28、 RNG RaNGing RSP ReSPonse RXD Receive Data SA Security Association SAID Security Association IDentity SAM Security Association Management SAP Service Access Point SBS Serving Base Station SBC Negotiate Basic Capabilities SDU Service Data Unit SET Setup SF Service Flow SS Subscriber Station TBS Targe
29、t Base Station TDD Time Division Duplexing TEK Encryption Key Transfer TFTP Trivial File Transfer Protocol TI Timer and counter TLV Type, Length, Value TP Test Purposes TSS Test Suite Structure TXD Transmit Data UCD Uplink Channel Descriptor UGS Unsolicited Grant Service UL Uplink VLAN Virtual Local
30、 Area Network 4 Test Suite Structure (TSS) 4.1 Structure Figure 1 shows the DLC Test Suite Structure (TSS) including its subgroups defined for conformance testing. Group Function Sub-functionCS options: Encapsulation Ipv46Ipv4 with ROHC / ECRTP Ipv6 with ROHC / ECRTP Ethernet Ipv4 over Ethernet Ipv6
31、 over Ethernet CS options: Classification Classifier DSx Signalling Ipv4 Classification General Ipv4 classification Ipv4 classification with ROHC Ipv4 classification with ECRTP Ipv6 Classification General Ipv6 classification Ipv6 classification with ROHC Ipv6 classification with ECRTP Ethernet class
32、ification Pure Ethernet classification Ipv4 over Ethernet ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 13Group Function Sub-function Ipv6 over Ethernet Payload Header Suppression MAC PDU Formats PDU concatenation Fragmentation Packing CRC ARQ Receiver operations Transmitt operationsReset Radio Link Contr
33、ol (Initial Network Entry and MAC Support of PHY layer) Initial Ranging Periodic Ranging Downlink Burst Profile Management To a Less Robust Profile To a More Robust Profile Negotiate Basic Capabilities Feedback mechanism MAC support for H-ARQ Support of different MAP IEs TBD list of functions in ter
34、ms of DL-MAP IEs and UL-MAP IEs; MAP Relevance Registration, IP connectivity and TFTP Registration IP ConnectivityDynamic Services (Service flow management) Service Addition Serv Change Service Deletion QoS Parameter Sets Bandwidth Allocation and Polling CDMA Bandwidth Request Request/Grant mechanis
35、m Multicast polling General Handover functionality Network topology acquisition Network Advertisement Scanning Association HO initiation Initiated by MSInitia by BS Network Re-Entry Acquisition of DL and UL parameters HO Ranging Capabilities Exchange EAP based Authentication/ Authorization Registrat
36、ion HO optimization Sleep mode General functions Power saving class type 1 Power saving class type 2 ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 14Group Function Sub-function Power saving class type 3 Periodic ranging during Sleep Mode Idle mode Transition to Idle Mode PagingNetwork Re-entry after Idle
37、Mode Expedited Network Re-entry after Idle Mode Location Update Multicast traffic connections Supported cryptographic suites No data encryption, no data authentication e.g. DS1 and DS3. 4.2.2 Main test types The main test types are the valid behaviour group, the invalid behaviour group and the inopp
38、ortune behaviour group. 4.2.2.1 Valid Behaviour (BV) tests This test group shall verify that the IUT reacts in conformity with the base specifications after receipt or exchange of valid Protocol Data Units (PDUs). Valid PDUs means that the exchange of messages and the content of the exchanged messag
39、es are considered as valid. 4.2.2.2 Invalid Behaviour (BI) tests This test sub group shall verify that the IUT reacts in conformity with the base specifications after receipt of a syntactically invalid PDU. 4.2.2.3 Inopportune Behaviour (BO) tests This test sub group shall verify that the IUT reacts
40、 in conformity with the base specifications after receipt of a syntactically correct PDU not expected in the actual message exchange. 4.2.2.4 Timer and counter (TI) tests This test group shall verify that the IUT reacts in conformity with the base specifications after expiry of a defined timer or co
41、unter. ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 185 Test Purposes (TP) 5.1 Introduction 5.1.1 TP definition conventions The TPs are defined by the rules shown in table 1. Table 1: TP definition rules TP Definition Item Item Description TP Id The TP Id is a unique identifier formed according to the TP
42、 naming conventions defined in clause 5.1.2. P802.16e Reference A pointer to the base specification requirement from which the TP is derived (specification reference, clause and paragraph). PICS Item The PICS item(s) associated with this TP. Initial Condition The IUTs state to which the TP is applie
43、d. Expected behaviour Definition of the events that are expected from the IUT pursuant to the base specification given a certain stimulus. Notes Additional optional information provided to the TP reader. ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 195.1.2 TP Identifier naming conventions The identifier
44、of the TP is built according to table 2. Table 2: TP naming convention Identifier: TP/-H = side type BS Base Station SS Subscriber Station (Mobile Station) = protocol group CSOE CS Options: Encapsulation CSOC CS Options: Classification PHS Payload Header Suppression MAC MAC PDU Formats ARQ ARQ RLC R
45、adio Link Control INI Registration, IP Connectivity, and Parameter Transfer DS Dynamic Services BWA Bandwidth Allocation and Polling GHF General Handover Functionality SLM Sleep Mode IDM Idle Mode MTC Multicast Traffic Connections SCS Supported Cryptographic Suites PKM Privacy and Key Management ver
46、sion 1 SEC Security version 2 CDM Channel Descriptors and Maps MBS Multicast and Broadcast Services AAS Adaptive Antenna Support RER Reset and Re-registration CCC Clock Comparison = function group IP4 IP version 4 IP6 IP version 6 IP4R IP version 4 with ROHC/ECRTP IP6R IP version 6 with ROHC/ECRTP E
47、NET Ethernet IP4oE IP version 4 over Ethernet IP6oE IP version 6 over Ethernet CDS Classifier DSx Signalling IP4C IP version 4 Classification IP6C IP version Classification ENTC Ethernet Classification CAT PDU Concatenation FRAG Fragmentation PACK Packing CRC Cyclic Redundancy Check RxD Receiver Ope
48、rations TxD Transmitter Operations RE Reset ACQ Acquisition of DL and UL parameters IRNG Initial Ranging PRNG Periodic Ranging DBPC Downlink Burst Profile Management SBC Negotiate Basic Capabilities FBK Feedback mechanism HARQ MAC support for H-ARQ MPIE Support of different MAP IEs REG Registration
49、IPC IP ConnectivityDSA Dynamic Service Addition DSC Dynamic Service Change DSD Dynamic Service Deletion QPS QoS Parameter Sets CBR CDMA Bandwidth Request REQ Request/Grant ETSI ETSI TS 102 545-2 V1.3.1 (2009-06) 20Identifier: TP/-H MCP Multicast Polling NTA Network Topology acquisition HOI Handover initiation NWR Network Re-entry HOO Handover Optimization GF General Functions PW1 Power Saving class type 1 PW2 Power Saving class type 2 PW3 Power Saving class type 3 PRSM Periodic Ranging during Sleep Mode TIDM Tran
