1、 ETSI TS 102 722-1 V2.1.1 (2010-03)Technical Specification Technical Committee for IMS Network Testing (INT);Originating Identification Presentation (OIP)and Originating Identification Restriction (OIR);Part 1: Protocol ImplementationConformance Statement (PICS)ETSI ETSI TS 102 722-1 V2.1.1 (2010-03
2、)2Reference DTS/INT-00001-1 Keywords SIP, PICS, OIP, OIR, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/8
3、8 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version
4、 is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status
5、. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notificatio
6、n No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2010. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo
7、 are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational P
8、artners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)3Contents Intellectual Property Rights 4g3Foreword . 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 6g33 Definitions and abbreviat
9、ions . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Protocol Implementation Conformance Statement (PICS) proforma . 7g34.1 Instructions for completing the PICS proforma 7g34.1.1 More detailed instructions are given at the beginning of the different clauses of the PICS proforma 7g34.1.1.1 Purposes
10、and structure. 7g34.1.2 Abbreviations and conventions . 7g34.2 Identification of the implementation 8g34.2.1 Date of the statement 8g34.2.2 Implementation Under Test (IUT) identification 9g34.2.3 System Under Test (SUT) identification 9g34.2.4 Product supplier 9g34.2.5 Client 9g34.2.6 PICS contact p
11、erson 9g34.3 PICS proforma tables . 9g34.3.1 Global statement of conformance . 9g34.3.2 Roles and network capabilities . 10g34.3.3 OIP/OIR user capabilities . 10g3History 11g3ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)4Intellectual Property Rights IPRs essential or potentially essential to the present d
12、ocument may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect
13、 of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the ex
14、istence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by IMS Network Testing (INT). The present document is part 1 of a multi
15、-part deliverable covering the Originating Identification Presentation (OIP) and Originating Identification Restriction (OIR) as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS)“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) a
16、nd partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification“. ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)51 Scope The present document specifies the Protocol implementation conformance statement (PICS) for the Originating Identification Presentation (OIP) and Originat
17、ing Identification Restriction (OIR) NGN Basic Service, TS 124 407 5. A further part of this multi-part deliverable specifies the Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma based on the present document. Within the TISPAN NGN Release
18、2, 3GPP release 8 Next Generation Network (NGN) the stage 3 description is specified using the IP Multimedia Call Control Protocol based on Session Initiation Protocol (SIP) and Session Description Protocol (SDP). The OIP service provides the terminating party with the possibility to receive a trust
19、ed (network-provided) identity of the originating party, and is applicable to all session-based services of the NGN. The OIR service enables the originating party to prevent presentation of any network-provided identity to the terminating party, and is applicable to all session-based services of the
20、 NGN. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. Non-specific reference may be made only to a complete document or a part thereof and only in the
21、 following cases: - if it is accepted that it will be possible to use all future changes of the referenced document for the purposes of the referring document; - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at h
22、ttp:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are indispensable for the application of the present document. For date
23、d references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. 1 ETSI TS 102 722-2: “Technical Committee for IMS Network Testing (INT); Originating Identification Presentation (OIP) and Originating Identifi
24、cation Restriction (OIR); Part 2: Test Suite Structure and Test Purposes (TSS Universal Mobile Telecommunications System (UMTS); LTE; TISPAN; PSTN/ISDN simulation services; Originating Identification Presentation (OIP) and Originating Identification Restriction (OIR); Protocol specification (3GPP TS
25、 24.407 Release 8)“. 6 IETF RFC 3325: “Private Extensions to the Session Initiation Protocol (SIP) for Asserted Identity within Trusted Networks“. 2.2 Informative references The following referenced documents are not essential to the use of the present document but they assist the user with regard t
26、o a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. i.1 ETSI ES 283 027: “Telecommunications and Internet converged Services and Protocols for Advanced Networking (TISPAN); Endorsement of the SIP-ISUP Interworkin
27、g between the IP Multimedia (IM) Core Network (CN) subsystem and Circuit Switched (CS) networks 3GPP TS 29.163 (Release 7), modified“. i.2 ETSI TS 183 007: “Telecommunications and Internet converged Services and Protocols for Advanced Networking (TISPAN); PSTN/ISDN simulation services; Originating I
28、dentification Presentation (OIP) and Originating Identification Restriction (OIR); Protocol specification“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: abstract test case: Refer to ISO/IEC 9646-1 2. Abstract Tes
29、t Suite (ATS): Refer to ISO/IEC 9646-1 2. Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 2. implicit send event: Refer to ISO/IEC 9646-3 3. lower tester: Refer to ISO/IEC 9646-1 2. Point of Control and Observation (PCO): Refer to ISO/IEC 9646-1 2. Protocol Implementation Conformance Statem
30、ent (PICS): Refer to ISO/IEC 9646-1 2. PICS proforma: Refer to ISO/IEC 9646-1 2. PIXIT proforma: Refer to ISO/IEC 9646-1 2. Protocol Implementation eXtra Information for Testing (PIXIT): Refer to ISO/IEC 9646-1 2. system under test: Refer to ISO/IEC 9646-1 2. Test Purpose (TP): Refer to ISO/IEC 9646
31、-1 2. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AS Application Server ATS Abstract Test Suite CLIP Calling Line Identification Presentation ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)7CLIR Calling Line Identification Restriction CN Core Network CS Cir
32、cuit SwitchedCSCF Call Session Control Function IP Internet ProtocolISDN Integrated Service Data Network n/a not applicable NGN Next Generation Network OIP Originating Identification Presentation OIR Originating Identification Restriction PSTN Public Switched Telephone Network S-CSCF Serving CSCF SD
33、P Session Description Protocol SIP Session Initiation Protocol SUT System Under Test URI Universal Resource Identifier 4 Protocol Implementation Conformance Statement (PICS) proforma Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that
34、users of the present document may freely reproduce the PICS proforma in this clause so that it can be used for its intended purposes and may further publish the completed PICS. 4.1 Instructions for completing the PICS proforma 4.1.1 More detailed instructions are given at the beginning of the differ
35、ent clauses of the PICS proforma The supplier of the implementation shall complete the PICS proforma in each of the spaces provided. If necessary, the supplier may provide additional comments separately in clause 5. 4.1.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mec
36、hanism whereby a supplier of an implementation of the requirements defined in reference specification 1 to 4 and ES 283 027 i.1 may provide information about the implementation in a standardized manner. The PICS proforma is subdivided into clauses for the following categories of information: instruc
37、tions for completing the PICS proforma; identification of the implementation; identification of the reference protocol specification; PICS proforma tables (containing the global statement of conformance). 4.1.2 Abbreviations and conventions The PICS proforma is composed of information in tabular for
38、m in accordance with the guidelines presented in ISO/IEC 9646-7 4. Item column: It contains a number that identifies the item in the table. ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)8Item description column: It describes each respective item (e.g. parameters, timers, etc.). Reference column: It gives r
39、eference to the OIP/OIR specification 1 and TS 183 007 i.2, except where explicitly stated otherwise. Status column: The following notations, defined in ISO/IEC 9646-7 4, are used for the status column: m mandatory - the capability is required to be supported. n/a not applicable - in the given conte
40、xt, it is impossible to use the capability. No answer in the support column is required. o optional - the capability may be supported or not. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items
41、and the logic of their selection which is defined immediately following the table. ci conditional - the requirement on the capability (“m“, “o“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression that is define
42、d immediately following the table. For nested conditional expressions, the syntax “IF . THEN (IF . THEN . ELSE.) ELSE .“ shall be used to avoid ambiguities. If an ELSE clause is omitted, “ELSE n/a“ shall be implied. NOTE: Support of a capability means that the capability is implemented in conformanc
43、e to the specifications 1 to 4 and ES 283 027 i.1. Support column: The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 4, are used for the support column: Y or y supported by the implementation. N or n not supported b
44、y the implementation. N/A or n/a no answer required (allowed only if the status is N/A, directly or after evaluation of a conditional status). 4.2 Identification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides - the System Under Test (SU
45、T) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. The product supplier information and client information should both be filled in if they are different. A person who can answer queries regarding information supplied in the ICS sh
46、ould be named as the contact person. 4.2.1 Date of the statement Date of the statement: ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)94.2.2 Implementation Under Test (IUT) identification IUT name: IUT version: 4.2.3 System Under Test (SUT) identification SUT name: Hardware configuration: Operating system:
47、 4.2.4 Product supplier Name: Address: Telephone number: Facsimile number: Additional information: 4.2.5 Client Name: Address: Telephone number: Facsimile number: Additional information: 4.2.6 PICS contact person Name: Telephone number: Facsimile number: Additional information: 4.3 PICS proforma tab
48、les 4.3.1 Global statement of conformance (Yes/No) Are all mandatory capabilities implemented? ETSI ETSI TS 102 722-1 V2.1.1 (2010-03)104.3.2 Roles and network capabilities Table 1: Roles and network capabilities Item Item description Reference Status Support 1 Is the implementation an originating u
49、ser equipment? 4.5.2.1 of 5 o 2 Is the implementation a terminating user equipment? 4.5.2.12 of 5 o 3 Is the implementation connected with a trusted network? 4.5.2.7, 4.5.2.8, 4.7.3 of 5 o 4 Is the implementation connected with an untrusted network? 4.5.2.7, 4.5.2.8, 4.7.3 of 5 o 5 Does the network insert the display-name in the P-Asserted-Identity? RFC 3325 6 o 6 The Application Server serving the originating user set the From header field to the default public user identities if the received Fr
