1、 ETSI TS 102 760-1 V1.2.1 (2014-06) Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for Access Technology Support (ISO 21218); Part 1: Implementation Conformance Statement (ICS) proforma Technical Specification ETSI ETSI TS 102 760-1 V1.2.1 (20
2、14-06)2Reference RTS/ITS-00260 Keywords CALM, ITS, PICS, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88
3、 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorizati
4、on of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be awa
5、re that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: ht
6、tp:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modif
7、ied without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit o
8、f its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)3Contents Intellectual Property Rights 5g3
9、Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 8g32 References 8g32.1 Normative references . 8g32.2 Informative references 8g33 Definitions and abbreviations . 9g33.1 Definitions 9g33.2 Abbreviations . 9g34 Conformance requirement concerning ICS 9g3Annex A (normative): Guidance for
10、 completing the ICS proforma 10g3A.1 Purposes and structure 10g3A.2 Abbreviations and conventions 10g3A.2.1 General . 10g3A.2.2 Item column 10g3A.2.3 Item description column . 10g3A.2.4 Status column . 11g3A.2.5 Reference column . 11g3A.2.6 Support column 11g3A.2.7 Values allowed column 11g3A.2.8 Va
11、lues supported column . 12g3A.2.9 References to items 12g3A.2.10 Prerequisite line 12g3A.3 Instructions for completing the ICS proforma 12g3Annex B (normative): Identification of the implementation 13g3B.1 General . 13g3B.2 Date of the statement 13g3B.3 Implementation Under Test (IUT) identification
12、 . 13g3B.4 System Under Test (SUT) identification 13g3B.5 Product supplier 14g3B.6 Client (if different from product supplier) 14g3B.7 ICS contact person . 15g3B.8 Identification of protocol 15g3B.9 Global statement of conformance . 15g3B.10 Detailed conformance declarations proforma 16g3Annex C (no
13、rmative): ICS proforma for ISO 21218 access technology support . 17g3C.1 General . 17g3C.2 Service Access Points . 17g3ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)4C.3 CI classification 17g3C.4 Address formats 18g3C.5 Procedures 19g3C.6 IN-SAP services . 20g3C.7 SNAP 20g3C.8 MI-SAP services 20g3C.9 COMMA
14、NDs and REQUESTs 21g3C.10 Events . 22g3C.11 Error/return codes . 22g3C.12 MIB parameters 23g3History 25g3ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)5Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to
15、these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Lat
16、est updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI We
17、b server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS). The present document is part 1 of a multi-part deliverable covering the test specifications
18、for ITS access technology support (service access points and related procedures) ISO 21218 1 as identified below: Part 1: “Implementation Conformance Statement (ICS) proforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial PIXIT proforma“. Modal
19、verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “may not“, “need“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and
20、 “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction Communications for Intelligent Transport Systems (ITS) is standardized at ISO TC204 WG16 under the acronym CALM (Communications Access for Land Mobiles). The communications architecture of ITS and coop
21、erative ITS and the concept of an ITS station (ITS-S) as a “Bounded Secured Managed Domain“ (BSMD) are specified in ISO 21217 i.1. The ITS station reference architecture is based on the OSI model as illustrated in figure 1. An implementation of a BSMD is named an “ITS station unit“ (ITS-SU), or more
22、 precisely and “Bounded Secured Managed Entity“ (BSME), which may consist of one or several physical units named “ITS station communication units“ (ITS-SCU). ITS-SCUs are interconnected via the ITS station-internal network specified in ISO 21217 i.1. ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)6Figure 1:
23、 Simplified ITS station reference architecture The OSI protocol layers of an ITS-S are grouped as shown in figure 1: The ITS-S access layer contains OSI layers 1 and 2, using the MI-interface towards the ITS-S management entity and the SI-interface towards the ITS-S security entity, and providing th
24、e IN-interface towards the ITS-S networking Testing; Framework for conformance and interoperability testing“. i.3 ISO 24102-4:2013: “Intelligent Transport Systems - Communications access for land mobiles (CALM) - ITS station management - Part 4: Station-internal management communication“. i.4 ETSI T
25、S 102 760-2: “Intelligent Transport Systems (ITS); Communications Access for Land Mobiles (CALM); Test specifications for Access Technology Support (ISO 21218); Part 2: Test Suite Structure and Test Purposes (TSS identification of the implementation; identification of the protocol; global statement
26、of conformance; ICS proforma tables. A.2 Abbreviations and conventions A.2.1 General The ICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 3. A.2.2 Item column The item column contains a number which identif
27、ies the item in the table. A.2.3 Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)11A.2.4 Status column The following nota
28、tions, defined in ISO/IEC 9646-7 3 and extended here, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or not. n/a not applicable - in the given context, it is impossible to use the capability. x prohibited (exclud
29、ed) - there is a requirement not to use this capability in the given context. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the logic of their selection which is defined immediately fo
30、llowing the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression which is defined immediately following the table. r as specified in the r
31、elated referenced standard of the CI. A.2.5 Reference column The reference column makes reference to ISO 21218 1, except where explicitly stated otherwise. A.2.6 Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO
32、/IEC 9646-7 3, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status). A.2.7 Values allowed column The values allow
33、ed column contains the type, the list, the range, or the length of values allowed. The following notations are used: - range of values: example: 5 20 - list of values: , , ., example: 2 ,4 ,6 ,8, 9 example: 1101B, 1011B, 1111B example: 0AH, 34H, 2FH - list of named values: (), (), ., () example: rej
34、ect(1), accept(2) - length: size ( ) example: size (1 8) ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)12A.2.8 Values supported column The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the ranges of values supported by the implementation sha
35、ll be indicated. A.2.9 References to items For each possible item answer (answer in the support column) within the ICS proforma a unique reference exists, used, for example, in the conditional expressions. It is defined as the table identifier, followed by a solidus character “/“, followed by the it
36、em number in the table. If there is more than one support column in a table, the columns are discriminated by letters (a, b, etc.), respectively. EXAMPLE 1: A.5/4 is the reference to the answer of item 4 in table 5 of annex A. EXAMPLE 2: A.6/3b is the reference to the second answer (i.e. in the seco
37、nd support column) of item 3 in table 6 of annex A. A.2.10 Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequisite line after a clause or table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. A.3 Instruc
38、tions for completing the ICS proforma The supplier of the implementation shall complete the ICS proforma in each of the spaces provided. In particular, an explicit answer shall be entered, in each of the “Support“ column boxes provided, using the notation described in clause A.2. If necessary, the s
39、upplier may provide additional comments in space at the bottom of the tables or separately. ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)13Annex B (normative): Identification of the implementation Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI gran
40、ts that users of the present document may freely reproduce the Identification of the implementation proforma in this annex so that it can be used for its intended purposes and may further publish the completed ICS proforma. B.1 General Identification of the Implementation Under Test (IUT) and the sy
41、stem in which it resides (the System Under Test (SUT) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. NOTE: The essential part of the IUT is the functionality specified in ISO 21218 1. The SUT, as a minimum, is a communication inte
42、rface (CI) as specified in ISO 21217 i.1. In what follows, the IUT thus referrers to the functionality specified in ISO 21218 1 applied in the context of a specific CI. The product supplier information and client information should both be filled in if they are different. A person who can answer que
43、ries regarding information supplied in the ICS should be named as the contact person. B.2 Date of the statement . B.3 Implementation Under Test (IUT) identification IUT name: . . IUT version: . B.4 System Under Test (SUT) identification SUT name: . . Hardware configuration: . . . ETSI ETSI TS 102 76
44、0-1 V1.2.1 (2014-06)14Operating system: . B.5 Product supplier Name: . Address: . . . Telephone number: . Facsimile number: . E-mail address: . Additional information: . . B.6 Client (if different from product supplier) Name: . Address: . . . Telephone number: . Facsimile number: . E-mail address: .
45、 ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)15Additional information: . . B.7 ICS contact person (A person to contact if there are any queries concerning the content of the ICS.) Name: . Telephone number: . Facsimile number: . E-mail address: . Additional information: . . B.8 Identification of protocol
46、This ICS proforma applies to the following standards: ISO 21218 1: CI standard reference: CI standard PICS reference: B.9 Global statement of conformance Are all mandatory capabilities implemented? (Yes/No) . NOTE: Answering “No“ to this question indicates non-conformance to the protocol specificati
47、on. Non-supported mandatory capabilities are to be identified in the ICS, with an explanation of why the implementation is non-conforming, on pages attached to the ICS proforma. ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)16B.10 Detailed conformance declarations proforma Detailed conformance declarations
48、 proforma are presented in annex C. ETSI ETSI TS 102 760-1 V1.2.1 (2014-06)17Annex C (normative): ICS proforma for ISO 21218 access technology support Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document ma
49、y freely reproduce the ICS proforma for ISO 21218 access technology support in this annex so that it can be used for its intended purposes and may further publish the completed ICS proforma. C.1 General Table C.1: Registration of CIs Item Method of registration of CIs in the SUT Reference Status Support 1 Dynamically using the standardized registration procedure 6.4.2 o Table C.2: Upper tester access Item Method of upper tester access in the SUT Reference Status Support 1 Applying IICP ISO 24102-3 2, ISO 24102-4 i.3 o
