1、 ETSI TS 105 175-1-1 V1.1.1 (2015-10) Access, Terminals, Transmission and Multiplexing (ATTM); Plastic Optical Fibres; Part 1: Plastic Optical Fibre System Specifications for 100 Mbit/s and 1 Gbit/s; Sub-part 1: Application requirements for physical layer specifications for high-speed operations ove
2、r Plastic Optical Fibres TECHNICAL SPECIFICATION ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 2 Reference RTS/ATTM-0240 Keywords application, fibre, optical, plastic ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00
3、017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any e
4、lectronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format
5、(PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/s
6、tatus.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photo
7、copying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2
8、015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks reg
9、istered and owned by the GSM Association. ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Abbreviations . 6g34 New home networking ap
10、plication requirements . 7g34.1 Introduction 7g34.2 FTTH deployment 8g34.3 Internet based services 8g34.4 Current in-home networking services. 9g34.5 Current home networking technologies 10g34.5.1 Introduction. 10g34.5.2 Ethernet CAT-5e/CAT-6 100 Mbit/s / 1 000 Mbit/s . 11g34.5.3 Wi-Fi 802. 11 a/b/g
11、/n/ac . 11g34.5.4 Power Line Communications (PLC) . 11g34.5.5 G.hn 11g34.5.6 POF (100 Mbit/s) 11g34.6 Current home networking topologies . 13g34.7 New application requirements 13g35 Gigabit POF as a the trunk home networking technology . 16g35.1 Introduction 16g35.2 POF installation advantages . 16g
12、35.3 POF based home networking topologies 17g35.4 Suitability of a POF-WiFi-CAT-5e hybrid network . 18g35.5 POF Standards 18g35.5.1 Introduction. 18g35.5.2 Fibre - IEC 60793-2-40 A4a.2 POF 18g35.5.3 EN 50173-1 and EN 50173-4 . 19g35.5.4 ETSI TS 105 175-1 (V2.0.0). 19g35.5.5 IEEE 802.3 100BASE-FX 21g
13、35.5.6 ETSI TS 105 175-1-2 1 Gbit/s and 100 Mbit/s data rate physical layer for Plastic Optical Fibre 21g35.5.7 Recommendation ITU-T G.9960 with Annex F for Plastic Optical Fibre 22g36 Requirements for 1 Gbit/s and 100 Mbit/s POF based applications . 22g36.1 Introduction 22g36.2 Physical layer requi
14、rements 22g36.3 Ethernet layer performance 23g36.4 Backwards compatibility 23g36.5 Environmental requirements 23g36.6 Topology requirements . 24g36.7 Energy Efficient Ethernet requirements . 24g36.8 Network Management requirements 24g36.9 Diagnostic and monitoring requirements . 24g36.10 Higher Leve
15、l System requirements 24g3History 25g3ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI me
16、mbers and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.ets
17、i.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the
18、 present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 1, sub-part 1 of a multi-part deliverable covering Plastic Optical fibre, as identified below: Part 1: “ P
19、lastic Optical Fibre System Specifications for100 Mbit/s and 1 Gbit/s“; Sub-part 1: “Application requirements for physical layer specifications for high-speed operations over Plastic Optical Fibres“; Sub-part 2: “1 Gbit/s and 199 Mbit/s physical later for Plastic Optical Fibres“. Modal verbs termino
20、logy In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in E
21、TSI deliverables except when used in direct citation. ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 5 1 Scope The present document provides a compendium of application requirements for full-duplex 100 Mbit/s and 1 Gbit/s Ethernet based home networking infrastructures based on Plastic Optical Fibre (POF)
22、 transmission media. The description of applications covers different network topologies as well as different field particularities. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For s
23、pecific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents, which are not found to be publicly available in the expected location, might be found at http:/docbox.etsi.org/Refe
24、rence. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long-term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI TS 105 175-1 (V2.0.0): “Access, Terminals, Transmissio
25、n and Multiplexing (ATTM); Plastic Optical Fibre System Specifications for 100 Mbit/s and 1 Gbit/s“. 2 IEC 60793-2:2011: “Optical fibres - Part 2: Product specifications - General“. 3 IEC 60793-2-40: “Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multim
26、ode fibres“. 4 IEC 60794-2-40: “Optical fibre cables - Part 2-40: Indoor optical fibre cables - Family specification for A4 fibre cables“. 5 ETSI TS 105 175-1-2: “Access, Terminals, Transmission and Multiplexing (ATTM); Plastic Optical Fibres; Part 1: Plastic Optical Fibre System Specifications for
27、100 Mbit/s and 1 Gbit/s; Sub-part 2: 1 Gbit/s and 100 Mbit/s physical layer for Plastic Optical Fibres“. 6 CENELEC EN 50173-1:2011: “Information technology - Generic cabling systems - Part 1: General requirements“. 7 CENELEC EN 50173-4:2007: “Information technology - Generic cabling systems - Part 4
28、: Homes“. 8 IETF RFC 2544: “Benchmarking Methodology for Network Interconnect Devices“. 9 IEEE 802.3: “IEEE Standard for Ethernet“. 10 Recommendation ITU-T Y.1564: “Ethernet service activation test methodology“. 2.2 Informative references References are either specific (identified by date of publica
29、tion and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the
30、time of publication, ETSI cannot guarantee their long-term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Recommendation ITU-T G.9960: “Unified high-speed wire-line base
31、d home networking transceivers - System architecture and physical layer specification“. ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 6 i.2 IEEE 802.3z: “Media Access Control Parameters, Physical Layers, Repeater and Management Parameters for 1,000 Mb/s Operation, Supplement to Information Technology -
32、Local and Metropolitan Area Networks - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications“. i.3 IEEE 802.3u: “Local and Metropolitan Area Networks-Supplement - Media Access Control (MAC) Parameters, Physical Layer, Medium Attachme
33、nt Units and Repeater for 100Mb/s Operation, Type 100BASE-T (clauses 21-30)“. i.4 IEEE 802.1Q: “IEEE Standard for Local and Metropolitan Area Networks - Virtual Bridged Local Area Networks“. i.5 IEEE 802.1p: “IEEE Standard for Local and Metropolitan Area Networks - Supplement to Media Access Control
34、 (MAC) Bridges: Traffic Class Expediting and Dynamic Multicast Filtering“. i.6 IEEE 802.1D: “IEEE Standard for Local and metropolitan area networks: Media Access Control (MAC) Bridges“. i.7 IEEE 802.11a -1999: “Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) specifications. High-sp
35、eed Physical Layer in the 5 GHz Band“. i.8 European Council Document 12608: “The potential dangers of electromagnetic fields and their effect on the environment“. i.9 Broadband Forum TR-069 Amendment 4: “CPE WAN Management Protocol“. i.10 IETF RFC from 3410 to 3418: “Internet Management Protocol. SN
36、MPv3“. i.11 Broadband Forum TR-143: “Enabling Network Throughput Performance Tests and Statistical Monitoring“. i.12 ICT ALPHA PUBLIC D1.1p: “Architectures for flexible Photonic Home and Access Networks - “End user future services in access, mobile and in building networks“. i.13 ANSI/TIA/EIA-568: “
37、Commercial Building Telecommunications Cabling Standards“. i.14 ISO/IEC 9314-3:1990: “Information processing systems - Fibre distributed Data Interface (FDDI) - Part 3: Physical Layer Medium Dependent (PMD)“. 3 Abbreviations For the purposes of the present document, the following abbreviations apply
38、: B2B Business-to-Business BER Bit Error Rate BW Bandwidth CAT Category CPE Customer Premises Equipment DECT Digital Enhanced Cordless Telecommunications DVB-X Digital Video Broadcasting technology ECG Electro Cardio Gram EHC Electronic Health CareEHG Electro Hystero Gram EMC Electro Magnetic Compat
39、ibility EMI Electro Magnetic Immunity EU European Union FDDI Fibre Distributed Data Interface FEC Forward Error Correction FER Frame Error Rate FTTH Fibre To The Home GOF Glass Optical Fibre HD High Definition ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 7 HDTV High Definition Television ICT Informatio
40、n and Communication Technologies IEC International Electrotechnical Commission IP Internet Protocol IPTV IP Television IT Information Technology ITU International Telecommunication Union ITU-T ITU Telecommunication Standardization Sector LC Lucent Connector MAC Media Access Control MDI Medium Depend
41、ent Interface MDU Multi Dwelling Units MIC Media Interface Connector MMOG Massively Multiplayers Online Games MTRJ Mechanical Transfer Registered Jack MTTFPA Mean Time To False Packet Acceptance MTU Maximum Transfer Unit NA Not Applicable NDIM Neighbouring Domain Interference Mitigation NIR Near Inf
42、ra Red NRZ Non Return to Zero NRZI Non Return to Zero Inverted OFDM Orthogonal Frequency De-multiplexing PAM Pulse Amplitude Modulation PCS Physical Coding SublayerPDA Personal Digital Assistant PHY Physical PLC Power Line Communications PMA Physical Medium Attachment PMD Physical Medium DependentPO
43、F Plastic Optical Fibre RFC Request for Comments (RFC) is a publication of the Internet Engineering Task Force RJ Registered Jack RX Reception SC Subscriber Connector SI-POF Step Index Plastic Optical Fibre ST Straight Tip connector STB Set Top Box STB/TV Set Top Box / Television TC Technical Commit
44、teeTV Television TX TransmissionUHDTV Ultra High Definition TV UPA Universal Powerline Association US United States of America VDE VDE, the Association for Electrical, Electronic including file sharing. Video-related services such as Video on Demand, IPTV, video conferencing and similar. Online Virt
45、ual Environments such as social network or gaming. Remote Technical services such as the ability to remotely control/survey your home. Remote Health services such as remote health monitoring. From the above classification, video-related services are among the most bandwidth demanding services with p
46、resence today at the home. A few examples follow: IPTV. ETSI ETSI TS 105 175-1-1 V1.1.1 (2015-10) 10 Video on Demand, multimedia content production and delivery. Video conferencing and video telephony. Video streaming/Home Theatre. TV Broadcast (DVB-X). Table 2 summarizing the demands for these appl
47、ications follows (see ICT Alpha i.12). Table 2: New application demands Service Bit rate Delay Jitter Packet loss Mobility Traffic Priority Security IPTV 2 Mbit/s to 20 Mbit/s (for HD) 400 ms; 200 ms recommended 50 ms 1 %; 0,1 % recommended Yes High No VoD 2 Mbit/s to 1 Gbit/s 400 ms; 200 ms recomme
48、nded 50 ms 1 %; 0,1 % recommended Yes High No Videoconference 128 kbit/s to 4 Mbit/s 400 ms; 200 ms recommended 50 ms 1 %; 0,1 % recommended Yes High No Video Streaming (uncompressed) 128 kbit/s to 10 Gbit/s 400 ms; 200 ms recommended 50 ms 1 %; 0,1 % recommended No High No TV Broadcast (DVB-IP) 96
49、kbit/s to 45 Mbit/s (HD) 400 ms 20 ms None (or use FEC) Yes High No TV Broadcast (DVB-x, non IP based) N/A rather BW occupied up to 8 MHz 400 ms 20 ms None (or use FEC) Yes High No Immersive TV (e.g. UHDTV) 24 Gbit/s uncompressed; 640 Mbit/s compressed 400 ms; 150 ms recommended 20 ms 0,4 % No High No Immersive Videoconference using UHDTV 640 Mbit/s compressed 400 ms; 150 ms recommended 20 ms 0,2 % No High No Stereoscopic TV 62,5 Mbit/s to 320 Mbit/s 400 ms; 150 ms recommended 20 ms 0,4 % No H
