1、 ETSI TS 1Digital cellular telecoUniversal Mobile TelUnstructured Supp(3GPP TS 22.0TECHNICAL SPECIFICATION122 090 V13.0.0 (2016communications system (Phaelecommunications System (pplementary Service Data (USStage 1 .090 version 13.0.0 Release 13GLOBAL SYSTEMOBILE COMMUN16-01) hase 2+); (UMTS); USSD)
2、; 13) TEM FOR ICATIONSRETSI ETSI TS 122 090 V13.0.0 (2016-01)13GPP TS 22.090 version 13.0.0 Release 13Reference RTS/TSGS-0122090vd00 Keywords GSM,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 74
3、2 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic an
4、d/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) versio
5、n kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If
6、 you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
7、microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rig
8、hts reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and
9、owned by the GSM Association. ETSI ETSI TS 122 090 V13.0.0 (2016-01)23GPP TS 22.090 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is pub
10、licly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETS
11、I Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or
12、 may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These
13、should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“,
14、“may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 122 090
15、V13.0.0 (2016-01)33GPP TS 22.090 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope 4g32 References 4g33 Abbreviations . 5g34 Description . 5g35 USSD operations MMI mode 5g35.1 Mobile initiated USSD operations 5g35.1.1 Ini
16、tiating action at the User Equipment (UE) . 5g35.1.2 Action at the network 5g35.1.3 Mobile initiated USSD cross phase compatibility 6g35.1.4 Allocation of service codes (to be noted by network operators) . 6g35.2 Network initiated USSD operation . 6g35.2.1 Initiating actions in the network . 6g35.2.
17、2 Actions at the UE 7g35.3 Network aspects of USSD operation 7g36 USSD operations application mode 7g36.1 General . 7g36.2 Mobile initiated transfer . 7g36.2.1 Initiating action at the UE . 7g36.2.2 Action in the network . 7g36.3 Network initiated transfer . 8g36.3.1 Initiating action in the network
18、 . 8g36.3.2 Action at the UE . 8g36.4 External addressing 8g36.5 Charging aspects 8g36.6 Compatibility aspects . 8g36.6.1 Mobile initiated transfer 8g36.6.2 Network initiated transfer . 8g36.7 Interaction with other services 8g36.8 Security 8g3Annex A (informative): Change history . 9g3History 10g3E
19、TSI ETSI TS 122 090 V13.0.0 (2016-01)43GPP TS 22.090 version 13.0.0 Release 13Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TS
20、G approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approv
21、al; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. 1 Scope
22、The present document defines the stage 1 description of Unstructured Supplementary Service Data (USSD) for use in one or a number of Public Land Mobile Networks (PLMNs). 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the presen
23、t document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (
24、including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TS 21.905: “Vocabulary for 3GPP Specifications“. 2 3GPP TS 22.004: “General on supplementary services“. 3 3GPP TS 22.030: “Man-Machine Inte
25、rface (MMI) of the Mobile Station (MS)“. 4 3GPP TS 23.038: “Alphabets and language-specific information“. 5 3GPP TS 24.080: “Mobile radio interface layer 3 supplementary services specification Formats and coding“. ETSI ETSI TS 122 090 V13.0.0 (2016-01)53GPP TS 22.090 version 13.0.0 Release 133 Abbre
26、viations For the purposes of the present document, the abbreviations listed in TS 21.905 1 apply. 4 Description There are two modes of USSD: MMI-mode and application mode. MMI-mode USSD is for the transparent transport of MMI strings entered by the user to the network and for the transparent transpo
27、rt of text strings from the network that are displayed by the mobile for user information. Application mode USSD is for the transparent transport of data between the network and the UE. Application mode USSD is intended to be used by applications in the network and their peer applications in the UE.
28、 The communication over the radio interface takes place on the signalling channels using short dialogues with peak data throughput rate capabilities of up to approximately 600 bits/s outside of a call and 1 000 bits/s during a call. 5 USSD operations MMI mode 5.1 Mobile initiated USSD operations 5.1
29、.1 Initiating action at the User Equipment (UE) If the user enters an MMI string that, according to TS 22.030 3, should be treated as USSD, the UE shall send this string to the network using the appropriate operation from TS 24.080 5. The mobile initiated operation shall contain an alphabet indicato
30、r and language indicator. The alphabet indicator shall indicate the alphabet used in the operation. The selection of values for these indicators is a matter for the user. The UE may initiate an USSD operation either during a call or out of call. 5.1.2 Action at the network A network supporting USSD
31、shall examine the alphabet indicator. If the serving network does not recognize the alphabet indicated in the mobile initiated USSD operation, it shall send the operation to the HLR. On recognition of the alphabet, the network shall examine the contents of the string, and take appropriate action, ac
32、cording to the following rules, depending of the format of the message. Case a) 1, 2 or 3 digits from the set (*, #) followed by 1X(Y), where X=any number 0-4, Y=any number 0-9, then, optionally “* followed by any number of any characters“, and concluding with # SEND: This case is reserved for HPLMN
33、 use. When a serving network receives such a message from a visiting subscriber, it shall pass the USSD message directly to the HPLMN. If it receives it from a home subscriber, it is up to the network to decide whether to treat it locally or to pass it to the HLR. Case b) 1, 2 or 3 digits from the s
34、et (*, #) followed by 1X(Y), where X=any number 5-9, Y=any number 0-9, then, optionally “* followed by any number of any characters“, and concluding with # SEND: This case is reserved for VPLMN use. It is up to the VPLMN to decide how to treat it. Case c) 7(Y) SEND, where Y=any number 0-9: This case
35、 is reserved for HPLMN use. When a serving network receives such a message from a visiting subscriber, it shall pass the USSD message directly to the HPLMN. If it receives it from a home subscriber, it is up to the network to decide whether to treat it locally or to pass it to the HLR. ETSI ETSI TS
36、122 090 V13.0.0 (2016-01)63GPP TS 22.090 version 13.0.0 Release 13Case d) All other formats: The visited network examines the message. If it is able, it acts upon it. Failing that, it passes the message to the HLR. If the HLR does not support the alphabet indicated, it shall inform the UE. The netwo
37、rk shall terminate the mobile initiated operation by responding to the request from the mobile with either an error signal, or a text string indicating the outcome of the operation. The response string uses the characters available in the selected alphabet as defined in TS 23.038 4. If no indication
38、 to the user is required, the response string may be empty. The response to the mobile initiated USSD operation shall contain alphabet and language indicators. The selection of values for these indicators is a matter for the network operator. 5.1.3 Mobile initiated USSD cross phase compatibility In
39、situations of incompatibility the mobile initiated USSD operation will be rejected by a non-supporting network and the attempt will fail. In this situation, if it is possible to encode the content of the USSD message in the IA5 alphabet, the UE shall attempt the operation again using the IA5 format
40、without the alphabet and language indicators. This procedure is not applicable if an operation failure is due to alphabet support problems, services not supported or network failure problems. 5.1.4 Allocation of service codes (to be noted by network operators) Service codes for use in control of Sup
41、plementary Services are standardized by international agreement, so must not be used by PLMNs unless authorized, except for those codes allocated for PLMN use. If the message is of the format: 1, 2 or 3 digits from the set (*, #), followed by NN(N), where N=0-9, optionally followed by “* and any num
42、ber of any characters“, and terminating in # SEND: then NN(N) is known as the service code. Only codes specified in TS 22.030 3 and those defined in cases a) and b) above may be used. All other values are reserved. Similarly, if the message is of the format: X(Y) SEND, where X=0-6 or 8-9 and Y=0-9:
43、the codes X(Y) are standardized. Only codes specified in TS 22.030 3 subclause 4.5.5 may be used. All other values are reserved. 5.2 Network initiated USSD operation 5.2.1 Initiating actions in the network At any stage while the UE is registered with a network, the network may send an unstructured s
44、tring to the UE. This string contains operator determined information that is relevant to the user. If the network is unable to successfully reach the UE, then an error shall be returned to the node that originated the operation. The network initiated USSD operation shall contain an alphabet indicat
45、or and language indicator. The alphabet indicator shall indicate the alphabet used in the operation. The selection of values for these indicators is a matter for the network operator. ETSI ETSI TS 122 090 V13.0.0 (2016-01)73GPP TS 22.090 version 13.0.0 Release 135.2.2 Actions at the UE If the is una
46、ble to process the network initiated USSD operation (e.g. the feature is not supported or the user is engaged in another MMI activity) then an error indication shall be returned to the node that originated the operation. If the alphabet indicated by the network is not supported by the UE, the UE sha
47、ll inform the network. The network may explicitly indicate to the UE that a response from the user is required. In this case, the next string entered by the user shall be used as the responseand this string is not interpreted according to normal MMI procedures stated in TS 22.030 3. An MMI command s
48、hall be provided to allow the user to terminate the dialogue with a null response. The response string uses the characters available in the selected alphabet as defined in TS 23.038 4. The response is sent to the node that originated the operation. If the network does not indicate that a response is
49、 required, then the normal MMI procedures on the UE continue to apply. The UE shall include alphabet and language indicators in the response to the network (if any). 5.3 Network aspects of USSD operation Applications that useUSSD operations may be located in either the HPLMN or a roamed to VPLMN. Network applications using USSD operations may: - use several USSD operations (possibly a mixture of mobile initiated and network initiated) in combination as part of a dialogue with the user. Linkage between separate operations as part of a dial
