1、 ETSI TS 1Universal Mobile TeEvolved Universal TerresSLm interface g(3GPP TS 36.4TECHNICAL SPECIFICATION136 456 V13.0.0 (2016Telecommunications System (ULTE; restrial Radio Access Network (e general aspects and principle6.456 version 13.0.0 Release 1316-01) (UMTS); k (E-UTRAN); les ) ETSI ETSI TS 13
2、6 456 V13.0.0 (2016-01)13GPP TS 36.456 version 13.0.0 Release 13Reference RTS/TSGR-0336456vd00 Keywords LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enreg
3、istre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present doc
4、ument shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive wit
5、hin ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present docume
6、nt, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by writ
7、ten permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMT
8、STMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETS
9、I TS 136 456 V13.0.0 (2016-01)23GPP TS 36.456 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and n
10、on-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). P
11、ursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present
12、document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being referen
13、ces to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“,
14、 “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 136 456 V13.0.0 (2016-01)33GPP TS 36.456 versi
15、on 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g31 Scope 5g32 References 5g33 Definitions, symbols and abbreviations . 5g33.1 Definitions 5g33.2 Symbols 5g33.3 Abbreviations . 5g33.4 Specification notations . 6g34 General aspects . 6
16、g34.1 E-UTRAN UTDOA architecture 6g34.2 SLm interface general principles 7g34.3 SLm interface specification objectives . 7g34.4 SLm interface capabilities 7g34.5 SLm interface characteristics . 8g34.5.1 Use of SCTP . 8g35 Functions of the SLm interface protocol 8g35.1 General . 8g35.2 SLm link manag
17、ement function . 8g35.3 SLm interface management function 8g35.4 SLm location function 8g36 SLm interface protocol structure 8g36.1 General . 8g36.2 SLmAP . 9g37 Other SLm interface specifications 9g37.1 E-UTRAN SLm interface: layer 1 (3GPP TS 36.457) . 9g37.2 E-UTRAN SLm interface: signalling trans
18、port (3GPP TS 36.458) . 9g37.3 E-UTRAN SLm Interface: SLmAP Specification (3GPP TS 36.459) . 9 g3Annex A (informative): Change history . 10g3History 11g3ETSI ETSI TS 136 456 V13.0.0 (2016-01)43GPP TS 36.456 version 13.0.0 Release 13Foreword This Technical Specification has been produced by the 3rdGe
19、neration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release da
20、te and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. techni
21、cal enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 136 456 V13.0.0 (2016-01)53GPP TS 36.456 version 13.0.0 Release 131 Scope The present document is an introduction to the 3GPP TS 36.45x serie
22、s of technical specifications that define the SLm interface for the interconnection of the Evolved Serving Mobile Location Centre (E-SMLC) to the Location Measurement Unit (LMU) components of the Evolved Universal Terrestrial Radio Access Network (E-UTRAN). 2 References The following documents conta
23、in provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specifi
24、c reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2
25、3GPP TS 36.305: “Evolved Universal Terrestrial Radio Access Network (E-UTRAN); Architecture description“. 3 3GPP TS 36.457: “Evolved Universal Terrestrial Radio Access Network (E-UTRAN); SLm interface layer 1“. 4 3GPP TS 36.458: “Evolved Universal Terrestrial Radio Access Network (E-UTRAN); SLm inte
26、rface signalling transport“. 5 3GPP TS 36.459: “Evolved Universal Terrestrial Access (E-UTRA); SLm interface Application Protocol (SLmAP)“. 6 IETF RFC 4960 (2007-09): “Stream Control Transmission Protocol“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present docu
27、ment, the terms and definitions given in TR 21.905 1 and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 1. 3.2 Symbols For the purposes of the present document, the following symbols apply: 3.3 Abbreviations For
28、 the purposes of the present document, the abbreviations given in TR 21.905 1 and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905 1. E-SMLC E-UTRAN Serving Mobile Location Centre eNB E-UTRAN Node
29、 B ETSI ETSI TS 136 456 V13.0.0 (2016-01)63GPP TS 36.456 version 13.0.0 Release 13EPC Evolved Packet Core EPS Evolved Packet System E-UTRAN Evolved UTRAN IP Internet ProtocolLMU Location Measurement Unit LTE Long Term Evolution MME Mobility Management Entity O - the SLm interface shall support the e
30、xchange of signalling information between the LMU and E-SMLC; - from a logical standpoint, the SLm is a point-to-point interface between an LMU within the E-UTRAN and an E-SMLC in the EPC. A point-to-point logical interface should be feasible even in the absence of a physical direct connection betwe
31、en the LMU and E-SMLC. 4.3 SLm interface specification objectives The SLm interface specification shall facilitate the following: - inter-connection of E-SMLCs with LMUs supplied by different manufacturers; - separation of SLm interface Radio Network functionality and Transport Network functionality
32、 to facilitate introduction of future technology. 4.4 SLm interface capabilities The SLm interface supports: - procedures to establish, maintain and release connections between the E-SMLC and LMUs; - the separation of each LMU on the protocol level for specific signalling management; - location serv
33、ices by transferring location requests from the E-SMLC to LMUs, and UL RTOA measurements from LMUs to E-SMLC; ETSI ETSI TS 136 456 V13.0.0 (2016-01)83GPP TS 36.456 version 13.0.0 Release 134.5 SLm interface characteristics 4.5.1 Use of SCTP The SCTP (IETF RFC 4960 7) is used to support the exchange
34、of SLm Application Protocol (SLmAP) signalling messages between an LMU and an E-SMLC. 5 Functions of the SLm interface protocol 5.1 General The following sections describe the functions to fulfil the SLm interface capabilities. 5.2 SLm link management function The SLm signalling link management func
35、tion provides a reliable transfer of the signalling between LMU and E-SMLC. 5.3 SLm interface management function The error indication function is used by the LMU (respectively the E-SMLC) to indicate to the E-SMLC (respectively the LMU) that a logical error has occurred. The reset procedure is used
36、 to initialize the peer entity after node setup and after a failure event has occurred. This procedure can be initiated by the E-SMLC or the LMU. The information about the LMU capabilities after a reset is preserved in the E-SMLC. The SLm Setup procedure allows the exchange of application level data
37、, e.g. capability, needed for the LMU and E-SMLC to interoperate correctly on the SLm interface. This procedure is originated by the LMU only and initiates the setup of the SLmAP contexts to the E-SMLC. 5.4 SLm location function The location function is used by the E-SMLC to request the LMU to perfo
38、rm UL RTOA measurements. The LMU reports UL RTOA measurements back to the requesting E-SMLC. 6 SLm interface protocol structure Editors Note: Protocol Structure following the structure defined in TS 36.305 2. 6.1 General The network signalling over SLm consists of the SLm Application Protocol (SLmAP
39、). The SLmAP consists of mechanisms to handle all procedures between the E-SMLC in the EPC and LMUs in the E-UTRAN. Over the SLm interface the SLmAP protocol is, e.g., used to: - Request LMUs to perform UL RTOA measurements of target UE SRS transmissions. - Transfer of completed UL RTOA measurements
40、 from the LMU to the E-SMLC. ETSI ETSI TS 136 456 V13.0.0 (2016-01)93GPP TS 36.456 version 13.0.0 Release 136.2 SLmAP Figure 6.1 shows the protocol structure for SLmAP, following the structure described in TS 36.305 2. Figure 6.1: Interface protocol structure for SLmAP The Transport Network Layer is
41、 based on IP transport, comprising SCTP on top of IP. 7 Other SLm interface specifications Editors Note: Description of the other related specifications. 7.1 E-UTRAN SLm interface: layer 1 (3GPP TS 36.457) 3GPP TS 36.457 3 specifies the physical layer technologies that may be used to support the SLm
42、 interface. 7.2 E-UTRAN SLm interface: signalling transport (3GPP TS 36.458) 3GPP TS 36.458 4 specifies the signalling bearers for the SLmAP for the SLm interface. 7.3 E-UTRAN SLm Interface: SLmAP Specification (3GPP TS 36.459) 3GPP TS 36.459 5 specifies the SLmAP for radio network control plane sig
43、nalling over the SLm interface. ETSI ETSI TS 136 456 V13.0.0 (2016-01)103GPP TS 36.456 version 13.0.0 Release 13Annex A (informative): Change history Change history Date TSG # TSG Doc. CR Rev Subject/Comment New 2012-12 58 RP-121766 Approved in RAN#58 and put under change control 11.0.0 2014-09 Update to Rel-12 version (MCC) 12.0.0 2015-12 Update to Rel-13 version (MCC) 13.0.0 ETSI ETSI TS 136 456 V13.0.0 (2016-01)113GPP TS 36.456 version 13.0.0 Release 13History Document history V13.0.0 January 2016 Publication
