1、 ETSI TS 186 014-1 V3.1.1 (2017-12) Core Network and Interoperability Testing (INT); Communication Diversion (CDIV) using IP Multimedia (IM) Core Network (CN) subsystem; (3GPP Release 12); Part 1: Protocol Implementation Conformance Statement (PICS) TECHNICAL SPECIFICATION ETSI ETSI TS 186 014-1 V3.
2、1.1 (2017-12)2 Reference RTS/INT-00143-1 Keywords conformance, CDIV, PICS, SIP, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture d
3、e Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modifi
4、ed without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Use
5、rs of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send
6、 your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission
7、of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for
8、 the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI TS
9、 186 014-1 V3.1.1 (2017-12)3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 6g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Confo
10、rmance to this PICS pro forma specification 7g34.0 The right to copy 7g34.1 Guidance for completing the PICS pro forma 7g34.1.0 Introduction. 7g34.1.1 Purposes and structure 7g34.1.2 Abbreviations and conventions . 7g34.1.3 Instructions for completing the PICS pro forma . 9g34.2 Identification of th
11、e implementation 9g34.2.0 Introduction. 9g34.2.1 Date of the statement 9g34.2.2 Implementation Under Test (IUT) identification 9g34.2.3 System Under Test (SUT) identification 9g34.2.4 Product supplier 10g34.2.5 Client (if different from product supplier) 10g34.2.6 PICS contact person 11g34.3 Identif
12、ication of the ETSI TS 124 604 . 11g34.3.0 Introduction. 11g34.4 Global statement of conformance . 11g34.5 Roles . 12g34.6 User role . 12g34.6.0 Introduction. 12g34.6.1 Major capabilities . 12g34.7 Network role . 13g34.7.0 Introduction. 13g34.7.1 Service capabilities . 13g34.7.2 Network capabilities
13、 . 13g34.7.3 Subscription options . 14g34.7.4 Simulation services . 15g34.7.5 Values . 15g3Annex A (informative): Bibliography . 16g3History 17g3ETSI ETSI TS 186 014-1 V3.1.1 (2017-12)4 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may
14、 have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI st
15、andards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
16、 referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of th
17、ese except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those t
18、rademarks. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability Testing (INT). The present document is part 1 of a multi-part deliverable covering Communication Diversion (CDIV), as identified below: Part 1: “Protocol Implementati
19、on Conformance Statement (PICS)“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification“. Modal verbs terminology In the present document “shall“, “shall not“, “should“,
20、 “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introd
21、uction To evaluate conformance of a particular implementation, it is necessary to have a statement of which capabilities and options have been implemented for a telecommunication specification. Such a statement is called an Implementation Conformance Statement (PICS). ETSI ETSI TS 186 014-1 V3.1.1 (
22、2017-12)5 1 Scope The present document specifies the Protocol Implementation Conformance Statement (PICS) for Communications Diversion (CDIV) services, ETSI TS 124 604 1 in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-7 7 and ETSI ETS
23、300 406 8. The Communications Diversion (CDIV) services enables diverting user, to divert the communications addressed to diverting user to another destination. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version nu
24、mber) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at
25、https:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI TS 124 604: “Digital cellul
26、ar telecommunications system (Phase 2+) (GSM); Universal Mobile Telecommunications System (UMTS); LTE; Communication Diversion (CDIV) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol specification (3GPP TS 24.604 Release 12)“. 3 ETSI TS 124 607 (V10.0.0): “Digital cellular telecommunic
27、ations system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Originating Identification Presentation (OIP) and Originating Identification Restriction (OIR) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol specification (3GPP TS 24.607 version 10.0.0 Release 10)“. 4
28、 ETSI TS 124 608: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Terminating Identification Presentation (TIP) and Terminating Identification Restriction (TIR) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol specificatio
29、n (3GPP TS 24.608 Release 12)“. 5 ETSI TS 124 611 (V10.2.0): “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Anonymous Communication Rejection (ACR) and Communication Barring (CB) using IP Multimedia (IM) Core Network (CN) subsystem; Pr
30、otocol specification (3GPP TS 24.611 version 10.2.0 Release 10)“. 6 ETSI TS 124 629: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Explicit Communication Transfer (ECT) using IP Multimedia (IM) Core Network (CN) subsystem; Protocol sp
31、ecification (3GPP TS 24.629 Release 12)“. 7 ISO/IEC 9646-7: “Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 7: Implementation Conformance Statements“. 8 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile con
32、formance testing specifications; Standardization methodology“. ETSI ETSI TS 186 014-1 V3.1.1 (2017-12)6 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited versi
33、on applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are
34、not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ISO/IEC 9646-1: “Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 1: General concepts“. 3 Definitions and abbrevia
35、tions 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-1 i.1, ISO/IEC 9646-7 7 and the following apply. ICS pro forma: document, in the form of a questionnaire, which when completed for an implementation or system becomes an ICS Implementation
36、 Conformance Statement (ICS): statement made by the supplier of an implementation or system claimed to conform to a given specification, stating which capabilities have been implemented NOTE: The ICS can take several forms: protocol ICS, profile ICS, profile specific ICS, information object ICS, etc
37、. Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification NOTE: This may contain additional information. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in ETSI TS 124 604 1 and the following apply: CDIV Commun
38、ication DIVersion CDIVN Communication DIVersion Notification CFB Communication Forwarding Busy CFNL Communication Forwarding on No Logged-in CFNR Communication Forwarding No Reply CFU Communication Forwarding Unconditional ICB Incoming Communications Barring ICS Implementation Conformance Statement
39、IP Internet ProtocolIUT Implementation under Test OCB Outgoing Communication Barring OIP Originating Identification Presentation OIR Originating Identification Restriction PICS Protocol Implementation Conformance Statement SIP Session Initiation Protocol SUT System Under Test TIP Terminating Identif
40、ication Presentation TIR Terminating Identification Restriction TP Test Purpose UE User Equipment ETSI ETSI TS 186 014-1 V3.1.1 (2017-12)7 URI Universal Resource Identifier 4 Conformance to this PICS pro forma specification 4.0 The right to copy Notwithstanding the provisions of the copyright clause
41、 related to the text of the present document, ETSI grants that users of the present document may freely reproduce the ICS proforma in this clause so that it can be used for its intended purposes and may further publish the completed ICS. 4.1 Guidance for completing the PICS pro forma 4.1.0 Introduct
42、ion If it claims to conform to the present document, the actual PICS pro forma to be filled in by a supplier shall be technically equivalent to the text of the PICS pro forma given in clause 4, and shall preserve the numbering/naming and ordering of the pro forma items. A PICS which conforms to the
43、present document shall be a conforming PICS pro forma completed in accordance with the guidance for completion given in clause 4.1. 4.1.1 Purposes and structure The purpose of this ICS pro forma is to provide a mechanism whereby a supplier of an implementation of the requirements defined in ETSI TS
44、124 604 1 may provide information about the implementation in a standardized manner. The PICS pro forma is subdivided into clauses for the following categories of information: guidance for completing the PICS pro forma; identification of the implementation; identification of the ETSI TS 124 604 1; g
45、lobal statement of conformance; roles; user role: - major capabilities; network role: - clause 4.7.1; - clause 4.7.2; - clause 4.7.3; - clause 4.7.4; - clause 4.7.5. 4.1.2 Abbreviations and conventions The ICS pro forma contained in this annex is comprised of information in tabular form in accordanc
46、e with the guidelines presented in ISO/IEC 9646-7 7. ETSI ETSI TS 186 014-1 V3.1.1 (2017-12)8 Item column The item column contains a number which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers
47、, etc.). It implicitly means “is the requirement or option supported by the implementation?“. Status column The following notations, defined in ISO/IEC 9646-7 7, are used for the status column: m mandatory - the capability is required to be supported. o optional - the capability may be supported or
48、not. n/a not applicable - in the given context, it is impossible to use the capability. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies an unique group of related optional items and the logic of their selection which is defined imm
49、ediately following the table. ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying an unique conditional status expression which is defined immediately following the table. Reference column The reference column makes reference to ETSI TS 124 604 1, except where explicitly stated otherwise. Support column The support column shall be filled in by the supplier of the implementation. The following common notations
