1、 Manufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards and, adjustable gap presses over48 inches right to left; and, solid gap presses over 50 inches right to left.NOTES: Press safety blocks must be installed in dies on diagon
2、ally oppositecorners during die maintenance except dies run in front feed blankets.Press safety blocks must be wedged in position shown whenever any partof the human body is extended into pinch points in any die duringrepairing or maintaining dies in presses.Each employee required to perform work in
3、 dies while dies are inpresses must have the standard DR8-0102 assigned wedges properlyinserted between the press safety block and the press ram.PRESSES EQUIPPED WITH SELF LOCKING RAM SLIDE LOCKS DO NOT REQUIRE THEUSE OF PRESS SAFETY BLOCKS.Manufacturing StandardsFord Motor Company199306 PRESSROOM S
4、AFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards anequal or greater number of bolts must be used as if the dies were being directlyfastened to the press.14. The use of long “Tee Slot Bolts” to “sandwich” risers between the die proper and thepress slide is not recommended and shou
5、ld be avoided except in cases where temporarybuild-ups for out-of-home line conditions dictate their use.Manufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards hydraulic presses - lockable device, etc.)The press supplier shall
6、document a load diagram, complete functional description, themounting, setting and maintenance instructions and all interlocks into the maintenancemanual of the press and a data plate on the press at operating point. A monthlypreventive maintenance check sheet shall be included by the press manufact
7、urer.Press slides which will receive multiple die stations shall have two press safety blocksper station to a maximum of six blocks.An adequate even number of press safety blocks of the required length (stroke +4.5 inches)shall be provided per Ford Manufacturing Standard DR8X. Where slide safety loc
8、ks arespecified and furnished and the Manufacturer of the press provides a document certifyingthey meet or exceed the 4:1 safety factor required by DR8X, the slide safety lockseliminate the requirement for use of safety blocks. However, the provided safety blocksmay be used by those employees who in
9、sist on their use because of the long standingpractice of only working between dies where safety blocks are in place. The use of theslide safety locks is the preferred method and eliminates handling of safety blocks.Manufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDES
10、IGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 13 of 20BLANKHOLDER PLATE PRESS FASTENING REQUIREMENTSManufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printe
11、d copies are uncontrolled.Systems Engineering (ESSE) Page 14 of 20DOUBLE AND TRIPLE ACTION DIE TO PRESS FASTENINGSAFETY REQUIREMENTSManufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.System
12、s Engineering (ESSE) Page 15 of 20SINGLE ACTION DIE TO PRESS FASTENINGAND “T“ SLOTTED GAP PRESSESManufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 16 of 20S
13、INGLE ACTION DIE TO PRESS FASTENINGWITH AIR RAM ADAPTORManufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 17 of 20DIE TO PRESS FASTENING IN KNEE PRESSESManuf
14、acturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 18 of 20DIE TO PRESS FASTENING IN O.B.I. PRESSESSAFETY NOTE: SEE DR8X PAGE 4 FOR DIE SETTING SAFETY PRACTICES.M
15、anufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 19 of 20TYPICAL BOLTING ASSEMBLIESSAFETY REQUIREMENTSFOR STRAIGHT SIDE PRESSESManufacturing StandardsFord Motor Company199306 PRESSROOM SAFETY ACCESSORIES DR8XDESIGN AND REFERENCE DATAEngineering Standards & Printed copies are uncontrolled.Systems Engineering (ESSE) Page 20 of 20DIE AND PUNCH RISER BOLTING REQUIREMENTS
