1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2013 12 12 N Status No replacement named L. Sinclair, NA 2007 06 29 Revised Inserted 3.0; Deleted 3.14 & 4 1969 08 12 Released CPX22-947881 Controlled document at www.MATS Copyright 2013, Ford Global Technologies, LLC Page 1 of 3 ADHESIVE, CO
2、NTACT - GASKET AND SEAL ESR-M11P17-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification defines the performance and product requirements for a synthetic rubber adhesive, solvent type. 2. APPLICATION This specification was released originally for material used on rocker cover gaskets. It is no
3、t intended to limit the adhesive to any specific material or material system, but rather defines the performance of the entire system. 3. REQUIREMENTS 3.1 Benzene in this material system is strictly prohibited. 3.2 Acid washed solvents having a sweet odor shall be used. 3.3 Shall be of medium consis
4、tency, formulated for brush application, and shall spread readily without drawing or pulling. 3.4 May require mild agitation prior to use. 3.5 Shall be resistant to oil, grease, water and most chemical solvents. The supplier shall furnish a list of chemical solvents that the material may not be resi
5、stant to so that compatibility testing may be conducted. 3.6 Must produce a firm secure bond without the use of heat or pressure. 3.7 Must be a one-part system not requiring additives to cure or set up a bond. 3.8 Provisions of this specification are applicable when the adhesive is used according to
6、 labeling directions, unless otherwise stated. Precautionary notes, such as the detrimental effect on painted surfaces, etc., involved in the use of the material should be clearly stated on the product label. 3.9 Must be reasonably safe to apply and must meet all federal, state and local regulations
7、 The material must be formulated to minimize health hazards to the individual due to toxic or otherwise injurious ingredients. 3.10 Must be capable of storage without any detrimental effect for an extended period of time. Supplier shall furnish all necessary information on types of material require
8、d for packaging and on the storage life of the material in each of the product packages supplied. For any particular size package or container for the product, the supplier shall furnish information on safe storage practice and recommendations as to maximum and minimum ambient temperatures and direc
9、t sun load conditions at which the product may be stored without any adverse effect. ENGINEERING MATERIAL SPECIFICATION ESR-M11P17-A Copyright 2013, Ford Global Technologies, LLC Page 2 of 3 3.11 Specific chemical and physical properties are not specified herein, but an Engineering Quality Control S
10、upplement will be issued to cover each approved material. The selected engineering approved source shall furnish appropriate chemical and physical properties along with the production tolerance limits that apply to the material(s) upon which approval was given. The agreed upon values and limits will
11、 be issued to Quality Control by the affected product engineering office. These values will then be used by Quality Control for ongoing quality verifications. The Quality Control Supplement is an integral requirement of this specification. If more than one source supplies material to this specificat
12、ion, a Quality Control Supplement will be issued for each specific approved material. 3.12 LABELING 3.12.1 Provisions of this specification are applicable when material is used according to labeling directions. Any precautions involved in the use of the material must be clearly stated on the product
13、 label. 3.12.2 The label(s) for the material(s) must comply to the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission and all other applicable federal, state and local regulations. Supplier shall furnish the affected product engineering office with
14、 the label(s). 3.12.3 Supplier shall furnish certification that the composition of his product has been examined and that the label recommended is in compliance with the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission. Completed Material Health
15、and Safety Data Sheets and Hazardous Substances Data Sheets must be submitted by the supplier to the Ford Motor Company toxicologist. 3.12.4 If applicable, supplier shall furnish a copy of the laboratory report wherein the product was evaluated under the procedures required by the Federal Hazardous
16、Substances Act. 3.12.5 Supplier must furnish detailed application instructions and specific usage information for container labels. This portion of the label information must be approved by the affected product engineering office. 3.12.6 If the label submitted by the supplier contains any advertisin
17、g claims, suitable corroborative testing data must also be furnished. Such claims and data are encouraged. 3.13 MARKING 3.13.1 Containers and cartons must be marked with a code indicating source and compounding date of the material. Supplier must furnish this code to the affected product engineering
18、 office. Container marking may be waived if approved in writing by the affected product engineering office. ENGINEERING MATERIAL SPECIFICATION ESR-M11P17-A Copyright 2013, Ford Global Technologies, LLC Page 3 of 3 5. GENERAL INFORMATION The information given below is provided for clarification and a
19、ssistance in meeting the requirements of this specification. 5.1 The test report data furnished by the supplier showing compliance with this specification shall give the specific test methods followed and shall give specific answers to generalized requirements. 5.2 Generally accepted test methods (A
20、merican Society for Testing and Materials, Society of Automotive Engineers and Ford Laboratory Test Methods are preferred) and procedures should be followed where such methods are known, otherwise the methods of evaluation should be explained in detail. 5.3 Comparative performance data ratings utilizing the requirements outlined above, comparing the proposed material(s) to presently marketed Ford Motor Company products, are encouraged.
