1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2007 09 28 Revised Inserted 3.0; Deleted 3.16 Revised 5. 1978 12 08 CPH22-815800-3 1969 05 26 Released CPY22-947841-1 Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 1 of 3 CLEANER, GLASS ESR-M14P5-A 1. SCOP
2、E This specification establishes the performance and product requirements for an automotive glass cleaner. 2. APPLICATION This specification was released originally for material used on both exterior and interior glass surfaces. This specification is not intended to limit the automotive glass cleane
3、r to any specific material or material system, but rather defines the performance of the entire system. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard requirements For Production Materials (WSS-M99P1111-A
4、). 3.1 Shall be of such composition that it meets all the requirements described in this specification. The material or material system must be in a form that lends itself to ease of application. It must be capable of application as purchased or with equipment normally available. 3.2 Must effectivel
5、y remove, with a minimum of time and effort, all deposits normally encountered on interior and exterior automotive glass surfaces. The glass surface shall have a clean, “like new“ appearance after cleaning. 3.3 Shall not streak, stain, etch or have abrasive action on the glass surface as it is being
6、 wiped off. 3.4 Any residue remaining from the material shall not cause smearing or any other adverse condition under the action of the windshield wiper blades. 3.5 No objectionable odor either during or after application of the material. 3.6 Shall have no detrimental effects on the glass surfaces o
7、n which it is applied or affect their function in any adverse way. 3.7 Shall have no detrimental effect on automotive parts with which it may come in contact, such as anodized aluminum, windshield wiper assemblies, convertible top and vinyl hardtop materials, upholstery materials or any associated m
8、aterial. ENGINEERING MATERIAL SPECIFICATION ESR-M14P5-A Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 2 of 3 3.8 The material shall meet the following specific test requirements: 3.8.1 Paint Staining No more than the master sample on file in the Quality Control L
9、aboratory. Test Method: Prepare paint panels according to FLTM BI 3-2. Paint colors to be used are black, white and metallic red in each of the following ESB numbers, M1J102-B, M4J54-A, M30J100-A and M32J100-A. To each of these 12 panels, apply the glass cleaner to a 2 in2 (1290 mm2). Allow to air d
10、ry 2 h maximum at 23 +/- 2 C. Expose the test panels in the fluorescent sun lamp cabinet as described in FLTM BU 5-1 for 24 h. Remove the panels, wash in tap water, observe for any effects on the painted surfaces. 3.8.2 Sprayability The material shall be dispensed rapidly, uniformly and shall have a
11、 spray pattern allowing a minimum of spray back. 3.8.3 Flammability The material and propellant shall be of such nature that there is a minimum danger due to flammability. Test Method: If the material is an aerosol, a flame projection must not exceed 18 in (457 mm) at full valve opening or have a fl
12、ashback at any degree of valve opening. Test procedure is found in para 191.15 of Volume 21, Code of Federal Regulations, Part 191. 3.9 Must be safe to apply and must meet all federal, state and local regulations. It must be formulated to minimize health hazards due to toxic or otherwise injurious i
13、ngredients. 3.10 The material or material system must be capable of storage without any detrimental effects for an extended period of time. Supplier shall furnish all necessary information on types of material required for packaging and on the storage life of the material in each of the product pack
14、ages supplied. For any particular size package or container for the product, the supplier shall furnish information on safe storage practice and recommendations as to maximum and minimum ambient temperatures and direct sun load conditions at which the product may be stored without any adverse effect
15、. If the package is considered unsafe for storage in an automotive vehicle, the package shall be labeled accordingly and the safe storage conditions specified. For all aerosol containers, the supplier shall furnish all pertinent information on pressures and propellants and any precautions involved i
16、n storing, handling and use. 3.11 CHEMICAL & PHYSICAL PROPERTIES Specific chemical and physical properties are not specified herein, but an Engineering Quality Control Supplement will be issued to cover each approved material. The selected engineering approved source shall furnish appropriate chemic
17、al and physical properties along with the production tolerance limits that apply to the material(s) upon which approval was given. The agreed upon values and limits will be issued to Quality Control by the affected product engineering office. These values will then be used by Quality Control for ong
18、oing quality verifications. The Quality Control Supplement is an integral requirement of this specification. If more than one source supplies material to this specification, a Quality Control Supplement will be issued for each specific approved material. ENGINEERING MATERIAL SPECIFICATION ESR-M14P5-
19、A Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 3 of 3 3.12 LABELING 3.12.1 Provisions of this specification are applicable when material is used according to labeling directions. Any precautions involved in the use of the material must be clearly stated on the p
20、roduct label. 3.12.2 The label(s) for the material(s) must comply with the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission and all other applicable federal, state and local regulations. Supplier shall furnish the affected product engineering off
21、ice with the label(s). 3.12.3 Supplier shall furnish certification that the composition of his product has been examined and that the label recommended is in compliance with the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission. Completed Material
22、 Health and Safety Data Sheets and Hazardous Substances Data Sheets must be submitted by the supplier to the Ford Motor Company toxicologist. 3.12.4 If applicable, supplier shall furnish a copy of the laboratory report wherein the product was evaluated under the procedures required by the Federal Ha
23、zardous Substances Act. 3.12.5 Supplier must furnish detailed application instructions and specific usage information for container labels. This portion of the label information must be approved by the affected product engineering office. 3.12.6 If the label submitted by the supplier contains any ad
24、vertising claims, suitable corroborative testing data must also be furnished. Such claims and data are encouraged. 3.13 MARKING Containers and cartons must be marked with a code indicating source and compounding date of the material. Supplier must furnish this code to the affected product engineerin
25、g office. Container marking may be waived if approved in writing by the affected product engineering office. 3.14 The test report data furnished by the supplier showing compliance with this specification shall give the specific test methods followed and shall give specific answers to generalized req
26、uirements. 3.15 Generally accepted test methods (American Society for Testing and Materials, Society of Automotive Engineers and Ford Laboratory Test Methods are preferred) and procedures should be followed where such methods are known, otherwise the methods of evaluation should be explained in deta
27、il. 5. GENERAL INFORMATION The information given below is given for clarification and assistance in meeting the requirements of this specification. 5.1 Comparative performance data ratings utilizing the requirements outlined above, comparing the proposed material(s) to presently marketed Ford Motor Company products, are encouraged.
