1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2002 01 30 Activated Rev para 3.2, 3.3, 3.5, 3.6, 3.7, 3.8 and 3.10, re-activated, updated & renumbered C. Kurz 1997 12 09 Inactivated 1974 10 21 Released CP022-739094 Printed copies are uncontrolled Page 1
2、of 4 Copyright 2002, Ford Global Technologies, Inc. CLOTH, DUSTING ESR-M99H93-B 1. SCOPE This specification defines the performance and product requirements for an automotive dusting and polishing cloth. This specification is not intended to limit the product to any specific material or material sys
3、tem, but rather defines the performance of the entire system. 2. APPLICATION This specification was released originally for material used as a dusting and polishing cloth for automotive exterior and interior surfaces. 3. REQUIREMENTS Material specification requirements are to be used for initial qua
4、lification of materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to the Companys Quality System Requirements. 3.2 GENERAL 3.2.1 The cloth shall be of such composition that meets all requirements described in this specification. The material must be in a for
5、m that easily lends itself to use. 3.2.2 The cloth shall have an affinity for dust and shall effectively remove a major portion of dust (not necessarily grimy dirt or soil) from automotive surfaces. 3.2.3 The cloth shall be uniform in texture, color, and construction. 3.2.4 The cloth shall be constr
6、ucted well enough to survive repeated uses and it shall still function after repeated washings and cleanings. 3.2.5 The cloth shall not leave a noticeable residue on any surface upon which it is used. 3.2.6 The cloth may or may not be impregnated with wax or polish. If so, the wax or polish shall be
7、 firmly impregnated into the cloth. The cloth shall not leave a noticeable residue per 3.2.5. The wax or polish impregnate shall not have to be wiped off with another cloth. The wax or polish impregnate shall not weaken the cloth or affect its uniformity or texture in any way. ENGINEERING MATERIAL S
8、PECIFICATION ESR-M99H93-B Page 2 of 4 Copyright 2002, Ford Global Technologies, Inc. 3.2.7 The cloth shall not contain any chemicals or abrasives which will harm the surfaces upon which it is used. 3.2.8 The cloth shall have no other detrimental effects on any of the surfaces upon which it is used.
9、3.2.9 While the cloth is specified for use on automotive interior and exterior surfaces, it should also be capable of being used in non-automotive applications (service garage or household use) and shall perform comparably to commercially available dusting cloths. 3.2.10 The cloth shall not be adver
10、sely affected by storage in a vehicle trunk or glove box. 3.3 CHEMICAL AND PHYSICAL PROPERTIES Specific chemical and physical properties are not specified herein, but an Engineering Quality Control Supplement will be issued to cover each approved material. The selected engineering approved source sh
11、all furnish appropriate chemical and physical properties along with the production tolerance limits that apply to the material(s) upon which approval was given. If requested, the agreed upon values and limits will be issued to Quality Control by the affected product engineering office. These values
12、will then be used by Quality Control for ongoing quality verifications. The Quality Control Supplement is an integral requirement of this specification. If more than one source supplies material to this specification, a Quality Control Supplement will be issued for each specific approved material. 3
13、.4 ODOR Not objectionable during use. 3.5 HEALTH AND SAFETY Must be safe to use and must be formulated to prevent a health hazard to any person using the product as directed. It must meet all federal, state, provincial, and local regulations for packaging, handling and labeling. 3.6 STORAGE Must be
14、capable of storage without any detrimental effect for two years. Supplier shall furnish all necessary information on types of material required for packaging and on the storage life of the material in each of the product packages supplied. For any particular size package or container for the product
15、, the supplier shall furnish information on safe storage practice and recommendations as to maximum and minimum ambient temperatures and direct sun load conditions at which the product may be stored without any adverse effect. If the package is considered unsafe for storage in an automotive vehicle,
16、 this information will be provided to the applicable Materials Engineering activity and the package shall be labeled accordingly and the safe conditions specified. ENGINEERING MATERIAL SPECIFICATION ESR-M99H93-B Page 3 of 4 Copyright 2002, Ford Global Technologies, Inc. 3.7 LABELING 3.7.1 Provisions
17、 of this specification are applicable when material is used according to labeling directions. Any precautions involved in the use of the material must be provided to the appropriate Materials Engineering activity and must be clearly stated on the product label. 3.7.2 The label(s) for the material(s)
18、 must comply to the Federal Hazardous Substances Act and all other provisions under the Consumer Product Safety Commission and all other applicable federal, state, provincial, and local regulations. 3.7.3 Upon request, Supplier shall submit a completed Ford Form 1291, Material Safety Data Sheet (MSD
19、S), and label or labeling statements for material to Ford Motor Company Toxicology, Occupational and Environmental Health Sciences. 3.7.4 Upon request, supplier shall furnish a copy of the laboratory report wherein the product was evaluated under the procedures required by the Federal Hazardous Subs
20、tances Act and/or other applicable federal, state, provincial, and local regulations. 3.7.5 Supplier must furnish to the applicable Materials Engineering activity detailed application instructions and specific usage information for container labels. This portion of the label information must be appr
21、oved by the applicable Materials Engineering activity. 3.7.6 If the label submitted by the Supplier contains any advertising claims, the Supplier must furnish suitable corroborative testing data to the applicable Materials Engineering activity. Such claims and data are encouraged. 3.8 MARKING Contai
22、ners and cartons must be marked as required per Ford Packaging Specification 1760 and the Quality Control Supplement. 3.9 TESTING REQUIREMENTS 3.9.1 The test report data furnished by the supplier showing compliance with this specification shall give the specific test methods followed and shall give
23、specific answers to generalized requirements. 3.9.2 Generally-accepted test methods (American Society for Testing and Materials, Society of Automotive Engineers and Ford Laboratory Test Methods are preferred) and procedures should be followed where such methods are known, otherwise the methods of ev
24、aluation should be explained in detail ENGINEERING MATERIAL SPECIFICATION ESR-M99H93-B Page 4 of 4 Copyright 2002, Ford Global Technologies, Inc. 3.10 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval w
25、as originally granted. Prior to making any changes to the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing and Materials Engineering activities of
26、the proposed changes, providing reasons for the change(s). Upon notification of the Company, the Company will provide further instructions to the Supplier. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance rest
27、rictions imposed by federal, state, provincial, and local regulations or Company direction apply to the materials addressed by this document. The Company restrictions are identified in Restricted Substance Management Standard WSS-M99P9999-A1. 4. APPROVAL OF SUPPLIERS Materials defined by this specif
28、ication for direct supply to the Company must have prior approval. Certain materials subcontracted by part suppliers may also require prior approval. These include materials critical to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreement
29、s. Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of
30、the test facility, demonstrating full compliance with all the requirements of this specification. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 Comparative performance data ratings utilizing the
31、requirements outlined above, comparing the proposed material(s) to presently marketed Ford Motor Company products, are encouraged. 5.2 For all engineering specifications and manufacturing standards referenced in this specification, the latest revision to this specification is applicable. 5.3 Any of the above requirements may be modified or waived pending the review of the suppliers data by the affected product engineering office.
