1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 00 2016 07 29 Released M. Souza, SA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 3 FABRIC, BELGRANO PATTERN, WARP KNIT, RECYCLED, WRS-M1H1126-A21 PIR/PCR CONTENT WITH SOIL REPELLANT 1. SCOPE The
2、 material defined by this specification is a warp (circular if applicable) knit polyester face fabric made from a minimum of 25% recycled content PIR/PCR (post industrial/post consumer) recycled yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fab
3、ric for Ecosport 2018 MY seat bolster. The fabric was originally approved as tri-laminated with foam and a backing scrim. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when
4、this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 APPPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FA
5、BRIC PERFORMANCE In addition to the requirements listed herein, the fabric shall meet all requiremen ts of WSS-M8P18-B1/B2/B3/B4/latest as applicable. 3.4 VEHICLE INTERIOR ENVIRONMENTAL PERFORMANCE Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest,
6、 Performance, Vehicle Interior Environmental Quality Material/Component Requirements. Data must be included in material submission package. 3.5 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23
7、 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. 3.6 FABRIC CONSTRUCTION 3.6.1 Fabric Count, +/- 10 Wales/Courses per 10 cm tolerance (ASTM D3775) Wales 120 / 10 cm Courses 190 / 10 cm ENGINEERING MATERIAL SPECIFICA
8、TION WRS-M1H1126-A21 Copyright 2016, Ford Global Technologies, LLC Page 2 of 3 3.6.2 Fabric Weight, -/+ 10 % tolerance 275 g/m (FLTM BN 106-01) 3.7 COMPOSITION (ASTM D629) Fabric 100% polyester 3.8 YARN CONSTRUCTION (ASTM D1244) Face 83 Dtex f24 (semi dull, round, polyester, FDY)Middle 110 Dtex f34
9、(semi dull, round, polyester, DTY) Back 75 denier f36 (semi dull, round, polyester, FDY) 4th 83 Dtex f24 (semi dull, round, polyester, FDY)3.9 RECYCLED CONTENT Recycled yarn must contain a minimum of 25% recycled content PIR/PCR (Postindustrial/post consumer) as defined by WRS-M99P42-A2. The remaini
10、ng portion of the material can come from virgin sources. Refer to the Approved Source List (ASL), for specific regional recycled levels for this material. Virgin yarn contains 100% virgin material. 3.10 METHOD OF DYEING Solution Dyed 3.11 FINISHED OPERATIONS Washing, Heat Setting, Lamination Any cha
11、nges to the above process must be approved by Materials Engineering. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase
12、departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. In the event of a Global Program or Regional duplication, each regional location of the supplier for this specification must provide a Construction pac
13、kage and be approved to meet this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the requirements of WSS-M8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to use tri-laminate/foam &
14、 scrim construction in all regions. ENGINEERING MATERIAL SPECIFICATION WRS-M1H1126-A21 Copyright 2016, Ford Global Technologies, LLC Page 3 of 3 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product De
15、velopment, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples
16、must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All material
17、s must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affe
18、cted Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested
19、 to the specifications for Design Verification (DV), Production Verification (PV) and Producation Part Approval Process (PPAP) sign off must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A/latest which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS
