1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2017 05 08 Released W. Andrews, NA Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 FABRIC, GROOVE PATTERN, DOBBY WOVEN, WRS-M1H1173-A21 RECYCLED, PIR/PCR CONTENT WITH SOIL REPELLANT 1. SCOPE Th
2、e material defined by this specification is a dobby woven polyester face fabric containing a minimum of 25% PIR/PCR (Post industrial/post consumer) recycled yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for Focus 2015 MY seat insert. The
3、 fabric was originally approved as trilaminated with foam and backing fabric/scrim. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the dr
4、awing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 APPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FABRIC PERFORMANCE In addition to the req
5、uirements listed herein, the fabric shall meet all requirements of WSS-M8P18-B1/B2/B3/B4/latest as applicable. 3.4 VEHICLE INTERIOR ENVIRONMENTAL PERFORMANCE Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest, Performance, Vehicle Interior Environme
6、ntal Quality Material/Component Requirements. Data must be included in material submission package. 3.5 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity
7、 Testing of the material should occur in the conditioning environment or soon after removal. 3.6 FABRIC CONSTRUCTION 3.6.1 Fabric Count, -/+ 10 % tolerance (ASTM D3775) Warp 273 / 10 cm Weft 181 / 10 cm ENGINEERING MATERIAL SPECIFICATION WRS-M1H1173-A21 Copyright 2017, Ford Global Technologies, LLC
8、 Page 2 of 3 3.6.2 Fabric Weight, -/+ 10 % tolerance (FLTM BN 106-01) Face fabric 302 g/m2 Scrim 35 g/m2 Total 337 g/m2 3.7 COMPOSITION (ASTM D629) Fabric 100% polyester 3.8 YARN CONSTRUCTION (ASTM D1244) Warp 600 Dtex f144, (polyester, semi-dull, air texturized, round section) Fill 600 Dtex f144, (
9、polyester, semi-dull, air texturized, round section) 3.9 RECYCLED CONTENT Recycled yarn must contain a minimum of 25% recycled content PIR/PCR (Postindustrial/post consumer) as defined by WRS-M99P42-A2. The remaining portion of the material can come from virgin sources. Refer to the Approved Source
10、List (ASL), for specific regional recycled levels for this material. 3.10 METHOD OF DYEING Solution dyed 3.11 FINISHED OPERATIONS Washing, SR treatment, drying Any changes to the above process must be approved by Materials Engineering. 4. GENERAL INFORMATION The information given below is provided f
11、or clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one
12、 supplier only. In the event of a Global Program or regional duplication, each regional location of the supplier for this specification must provide a construction package and be approved to meet this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, compositi
13、on and yarn construction. The fabric must also meet the requirements of WSS-M8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to use tri-laminate/foam & scrim construction in all regions. ENGINEERING MATERIAL SPECIFICATION WRS-M1H1173-A21 Copyright 2017, Ford Global Technologies, LLC
14、Page 3 of 3 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualif
15、ied and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated q
16、uality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes t
17、o the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by
18、submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign of
19、f must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1/latest which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS
