FORD WSB-M4D874-A-2010 POLYVINYL CHLORIDE (PVC) FLEXIBLE 80 DUROMETER A HARDNESS REMANUFACTURED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《硬度为80 A的柔性聚氯乙烯(PVC)废料再生成型料 .pdf

上传人:priceawful190 文档编号:749154 上传时间:2019-01-14 格式:PDF 页数:3 大小:28.01KB
下载 相关 举报
FORD WSB-M4D874-A-2010 POLYVINYL CHLORIDE (PVC) FLEXIBLE 80 DUROMETER A HARDNESS REMANUFACTURED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  《硬度为80 A的柔性聚氯乙烯(PVC)废料再生成型料  .pdf_第1页
第1页 / 共3页
FORD WSB-M4D874-A-2010 POLYVINYL CHLORIDE (PVC) FLEXIBLE 80 DUROMETER A HARDNESS REMANUFACTURED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  《硬度为80 A的柔性聚氯乙烯(PVC)废料再生成型料  .pdf_第2页
第2页 / 共3页
FORD WSB-M4D874-A-2010 POLYVINYL CHLORIDE (PVC) FLEXIBLE 80 DUROMETER A HARDNESS REMANUFACTURED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  《硬度为80 A的柔性聚氯乙烯(PVC)废料再生成型料  .pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 01 25 N-STATUS No replacement named J. Crist, NA 2006 05 22 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.5, 3.6 & 4 1993 03 08 Released - A NB00I10043054228 GAM M. Myers Printed copies are uncontrolled Copyright 2010, Ford Global Techno

2、logies, LLC Page 1 of 3 POLYVINYL CHLORIDE (PVC), FLEXIBLE WSB-M4D874-A 80 DUROMETER A HARDNESS, REMANUFACTURED MOLDING COMPOUND POLYVINYL CHLORIDE (PVC), FLEXIBLE WSB-M4D874-A2 92 DUROMETER A HARDNESS, REMANUFACTURED MOLDING COMPOUND NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by t

3、hese specifications are remanufactured flexible polyvinyl chloride extrusion molding compounds. 2. APPLICATION These specifications were released originally for material used for exterior splash shield and air dam applications. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Mater

4、ial suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 MOLDED TEST SPECIMEN 3.4.1 Preparation of Test Specimens Unless otherwise specified, all test shall be conducted on specimens die cut from extruded sheet 150 x 150 mm, m

5、inimum x 2.0 +/- 0.2 mm. A A2 3.4.2 Density, g/cm 1.24-1.36 1.22-1.42 (ISO 1183, Method A/ASTM D 792, Method A) 3.4.3 Hardness, Durometer A, +/- 5 80 92 (ISO 868/ASTM D 2240, 6 mm thick plied-up specimens, 15 s delay) 3.4.4 Tensile Strength at Break, MPa, min (ISO R 527, type 2/ASTM D 638M, type M-I

6、I, 500 mm/min test speed) WMD 9 13 AMD 6 9 ENGINEERING MATERIAL SPECIFICATIONWSB-M4D874-A/A2 Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 3 3.4.4.1 Elongation at Break, %, min (Test Method according to para 3.4.4) A A2 WMD 140 80 AMD 90 50 3.4.5 Tear Streng

7、th, kN/m, min (ISO 34,Method B, Procedure a/ ASTM D 624, Die C) WMD 30 34 AMD 40 45 3.4.6 Cold Flexibility at -29 C No cracks No cracks (FLTM BN 102-01, except specimen 25 x 150 mm, minimum and 19-20 mm mandrel) 3.4.7 Color Stability (ISO 188/ASTM D 573, 168 h at 100 +/- 2 C) After exposure the mate

8、rial shall not exhibit color change in excess of Rating 4 of specified Gray Scale (AATCC Evaluating Procedure 1/ISO 105-A02). In addition there shall not be any staining, spewing, loss of gloss. 3.4.8 Heat Aging Performance (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 1000 h at 82 +/- 2 C. Unaged

9、property values shall be determined at the time of the aged properties determination) 3.4.8.1 Tensile Strength Change +/- 25% (Test Method per para 3.4.4) 3.4.8.2 Elongation Change +/- 25% (Test Method per para 3.4.4) 3.4.8.3 Weight Change, max 5% (50 x 25 x 2 +/- 0.2 mm specimen) 3.4.9 Paint Staini

10、ng (FLTM BP 153-01, Procedure A, 25 x 50 x 2.0 +/- 0.2 mm specimen) No visible stain or change in surface appearance produced on the painted panel beyond the boundaries of the test specimen. ENGINEERING MATERIAL SPECIFICATIONWSB-M4D874-A/A2 Printed copies are uncontrolled Copyright 2010, Ford Global

11、 Technologies, LLC Page 3 of 3 Note: The raised welting of the painted surfaces in direct contact with the test specimen resulting from this test method is characteristic of plasticized vinyl compounds and shall not be cause for rejection. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of these specifications. 5.1 RECYCLING CODE, (A & A2) PVC

展开阅读全文
相关资源
猜你喜欢
  • EN 792-13-2000 en Hand-held non-electric power tools - Safety requirements - Part 13 Fastener driving tools (Incorporates Amendment A1 2008)《手持非电动工具 安全要求 第13部分 紧固件传动工具 包含修改件A1-2008.pdf EN 792-13-2000 en Hand-held non-electric power tools - Safety requirements - Part 13 Fastener driving tools (Incorporates Amendment A1 2008)《手持非电动工具 安全要求 第13部分 紧固件传动工具 包含修改件A1-2008.pdf
  • EN 792-8-2001 en Hand-held non-electric power tools - Safety requirements - Part 8 Sanders and polishers (Incorporates Amendment A1 2008)《手持非电动工具 安全要求 第8部分 砂轮机和抛光机 包含修改件A1-2008》.pdf EN 792-8-2001 en Hand-held non-electric power tools - Safety requirements - Part 8 Sanders and polishers (Incorporates Amendment A1 2008)《手持非电动工具 安全要求 第8部分 砂轮机和抛光机 包含修改件A1-2008》.pdf
  • EN 794-3-1998 en Lung ventilators - Part 3 Particular requirements for emergency and transport ventilators (Incorporates Amendment A2 2009)《肺呼吸器 第3部分 紧急和移动呼吸器的特殊要求 包含修改件A2-2009》.pdf EN 794-3-1998 en Lung ventilators - Part 3 Particular requirements for emergency and transport ventilators (Incorporates Amendment A2 2009)《肺呼吸器 第3部分 紧急和移动呼吸器的特殊要求 包含修改件A2-2009》.pdf
  • EN 795-2012 en Personal fall protection equipment - Anchor devices《防止从高处跌落 抛锚设备》.pdf EN 795-2012 en Personal fall protection equipment - Anchor devices《防止从高处跌落 抛锚设备》.pdf
  • EN 797-1995 en Bar Coding - Symbology Specifications - `EAN UPC (Incorporating Corrigendum October 1996)《条形码 术语规范 合并勘误表-1996年10月》.pdf EN 797-1995 en Bar Coding - Symbology Specifications - `EAN UPC (Incorporating Corrigendum October 1996)《条形码 术语规范 合并勘误表-1996年10月》.pdf
  • EN 80-2001 en Wall Hung Urinals - Connecting Dimensions《墙挂式便器 连接尺寸》.pdf EN 80-2001 en Wall Hung Urinals - Connecting Dimensions《墙挂式便器 连接尺寸》.pdf
  • EN 802-1994 en Plastics Piping and Ducting Systems - Injection-Moulded Thermoplastics Fittings for Pressure Piping Systems - Test Method for Maximum Deformation by Crushing《塑料管道和管道.pdf EN 802-1994 en Plastics Piping and Ducting Systems - Injection-Moulded Thermoplastics Fittings for Pressure Piping Systems - Test Method for Maximum Deformation by Crushing《塑料管道和管道.pdf
  • EN 803-1994 en Plastics Piping Systems - Injection-Moulded Thermoplastics Fittings for Elastic Sealing Ring Type Joints for Pressure Piping - Test Method for Resistance to a Short-.pdf EN 803-1994 en Plastics Piping Systems - Injection-Moulded Thermoplastics Fittings for Elastic Sealing Ring Type Joints for Pressure Piping - Test Method for Resistance to a Short-.pdf
  • EN 804-1994 en Plastics Piping Systems - Injection-Moulded Socket Fittings for Solvent-Cemented Joints for Pressure Piping - Test Method for Resistance to a Short-Term Internal Hyd.pdf EN 804-1994 en Plastics Piping Systems - Injection-Moulded Socket Fittings for Solvent-Cemented Joints for Pressure Piping - Test Method for Resistance to a Short-Term Internal Hyd.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1