1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2007 05 16 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.6 & 4 1995 05 04 Revised 1994 11 04 Released J.D. Salow A.J. Stocki Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 1 of 3 LAMINATE, POLYVINYL CHLORI
2、DE + ABS BLEND (PVC+ABS) WSB-M98D31-A2 OR POLYVINYL CHLORIDE (PVC) SKIN/POLYOLEFIN FOAM/POLYOLEFIN (PP) SKIN, LOW PRESSURE MOLDING 1. SCOPE The material defined by this specification is an adhesively bonded laminate consisting of PVC+ABS blend or a PVC cover material, polyolefin foam, and polyolefin
3、 skin. 2. APPLICATION This specification was released originally for material used in interior trim as a covering for automotive door panels, seat back panels, or door panel inserts produced by the low pressure molding process. 3. REQUIREMENTS In addition to the requirements listed herein, this mate
4、rial shall meet all requirements of the WSB-M8P3-C, PERFORMANCE, FLEXIBLE POLYMERIC FILM, INTERIOR QUALITY material performance specification. Assemblies specifying WSB-M98D31-A2 must also meet the requirements of WSB-M15P4-D, INTERIOR TRIM-ASSEMBLY PERFORMANCE SPECIFICATION, unless otherwise specif
5、ied on the Engineering Drawing. Unitized or integral armrests shall also meet the requirements of WSB-M15P26-C, PERFORMANCE, ARMREST, FORMED. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Mat
6、erials (WSS-M99P1111-A). 3.4 SKIN/FOAM/SKIN LAMINATE 3.4.1 Dimensions * (Skin/foam/skin laminate thickness) PVC+ABS or PVC skinn 0.574 - 0.625 mm *Polyolefin foam 2.125 - 2.875 mm *Polyolefin skin 0.373 - 0.424 mm Total 3.072 - 3.924 mm * Refer to engineering drawing for foam density, thickness, and
7、 backskin thickness. Test Method: Cut several 12.7 x 75 mm samples from separate areas of the test specimen and examine the cross sectional view of the skin to foam laminate using a measuring magnifier (ex. Bausch & Lombs Measuring Magnifier (7X), Catalog No. 81-34-35 with the system scale No. 81-34
8、37, or equivalent). Measure the thickness of each component and the total thickness of the laminate at several points along the cut surface of the cross section. ENGINEERING MATERIAL SPECIFICATION WSB-M98D31-A2 Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 2 of
9、3 3.4.2 Tensile Strength, min 2.1 MPa (ISO 1798/ASTM D 3574, Test E, 50 mm bench marks, 5 specimens min, any direction) 3.4.2.1 Elongation, min 185% (Test according to 3.4.2) 3.4.3 Tear Strength, min 12 kN/m (ISO 34, Method B, Procedure A/ ASTM D 1004, any direction) 3.4.4 Hardness, Durometer A 75 +
10、/- 5 (ASTM D 2240, 15 s dwell) 3.4.5 Adhesion, (Skin to Foam), min (ISO 2411, Standard Method, 300 mm/minute (NAAO)/FLTM BN 151-05 (EAO), any direction) Adhesion of top and bottom skin to foam must exhibit 100% foam tear. Room Temperature 0.5 kN/m After 30 minutes at 100 +/- 2 C 0.5 kN/m (condition
11、30 minutes at RT and test) 3.4.6 Resistance to Abrasion, min 500 cycles (FLTM BN 108-02, CS-10 wheels, 1000 g load) The surface shall show no evidence of wearthrough, and the color of the abraded area shall be compatible in appearance with the adjacent unabraded area. 3.4.7 Coating Adhesion (FLTM BI
12、 106-01, Method C) The tape shall not lift or delaminate the surface coating. 3.4.8 Crazing The PVC+ABS or PVC skin surface of the laminate shall not exhibit crazing or whiteness when folded or creased. 3.4.9 Dimensional Stability (SAE J883, 7 days at 90 +/- 2 C) MD & AMD +/- 5% Shall show no eviden
13、ce of delamination or blistering. ENGINEERING MATERIAL SPECIFICATION WSB-M98D31-A2 Printed copies are uncontrolled Copyright 2007, Ford Global Technologies, LLC Page 3 of 3 3.4.10 Resistance to Migration Staining and Blocking (FLTM BN 103-01) No evidence of injurious exudation, adhesion (tackiness),
14、 separation, color transfer, staining, or flattening of embossing when placed face to face with itself and the standard vinyl test material. In addition, place face to back to assure any adhesion promotor does not cause undesired adhesion. 3.4.11 Flammability (ISO 3795/SAE J369) Burn Rate, max 100 m
15、m/minute 3.5 RIGID SUBSTRATE (Only required of the component manufacturer) Rigid substrates, such as WSB-M4D841-A2, or equivalent dimensionally stable substrates, shall meet the requirements of their respective engineering specifications, as well as the assembly requirements specified herein. 3.5.1
16、Peel Adhesion, Skin/Foam/Skin to Rigid Substrate, min (ISO 2411 (NAAO), Standard Method, 300 mm/minute/FLTM BN 151-05 (EAO), any direction) Adhesion of skin/foam/skin to substrate must exhibit 100% foam tear. Room Temperature 880 N/m width Tested at 93 +/- 3 C after 1 h 132 N/m width exposure at thi
17、s temperature 3.5.2 Florida & Arizona Exposure (SAE J2230, AATCC Evaluation Procedure 1/ ISO 105-A02) 1500 kJ/m2 Rating 3.0 The material shall not stain, exhibit color tone change or change in hue in excess of the specified Gray Scale rating. In addition, there shall be no cracking, crazing, or other deterioration.
