FORD WSE-M3G193-A2-2006 LABEL EMISSION CERTIFICATION INTERIOR QUALITY TO BE USED WITH FORD WSS-M99P1111-A 《车内级排放鉴定标签 与标准FORD WSS-M99P1111-A一起使用 》.pdf

上传人:bonesoil321 文档编号:750098 上传时间:2019-01-14 格式:PDF 页数:2 大小:70.03KB
下载 相关 举报
FORD WSE-M3G193-A2-2006 LABEL EMISSION CERTIFICATION INTERIOR QUALITY  TO BE USED WITH FORD WSS-M99P1111-A  《车内级排放鉴定标签  与标准FORD WSS-M99P1111-A一起使用 》.pdf_第1页
第1页 / 共2页
FORD WSE-M3G193-A2-2006 LABEL EMISSION CERTIFICATION INTERIOR QUALITY  TO BE USED WITH FORD WSS-M99P1111-A  《车内级排放鉴定标签  与标准FORD WSS-M99P1111-A一起使用 》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 01 25 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.10, 4 1991 02 13 Released NEO1-E-10000474-091 E. J. Duda Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 1 of 2 LABEL, EMISSION CERTIFICATION, INTERIO

2、R QUALITY WSE-M3G193-A2 1. SCOPE The material defined by this specification is a polyester film with a pressure sensitive adhesive protected by a suitable release line. 2. APPLICATION This specification was released originally for labels used to state the vehicle emission control information as requ

3、ired by the Federal regulations or as specified on the engineering drawing. It is applied to the mounting surface by removing the release paper and pressing firmly into place. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the

4、 Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 APPEARANCE Shall be free of streaks, blisters, wrinkles, ragged edges, smeared printing, and any other surface imperfections which will make them unsuitable for the intended usage. The design and color shall be as specifi

5、ed on the engineering drawing. 3.5 PREPARATION OF LABELS ON GLASS PANELS Clean glass panels with alcohol and allow the surface to dry. Place the label on the glass panels with a 2.0 kg rubber roller with one edge or side not adhered (about 20% of the total area). Condition for 24 h minimum at 23 +/-

6、 2 C and 50 +/- 5% relative humidity. 3.6 ORIGINAL ADHESION, min 600 N/m width (ASTM D 1000, 180 peel) 3.7 ENVIRONMENTAL TESTING OF PANEL ASSEMBLY Test shall be performed immediately after removal from the conditioning environment. After each of the environmental exposures, the label must not show e

7、vidence of delamination, loss of printing or any other effect which would detract from its proper function or appearance. 3.7.1 Direct a stream of air 400 - 500 kPa pressure with a 2.4 mm diameter orifice and at a distance of approximately 75 mm from the decals edge for 3 minutes at a right angle to

8、 the surface and then for 3 minutes at a 10 angle to its edge. 3.7.2 Humidity cabinet for 168 h at 38 +/- 2 C and 98 +/- 2%relative humidity. Adhesion - 180 Peel 385 N/m width ENGINEERING MATERIAL SPECIFICATIONWSE-M3G193-A2Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC

9、 Page 2 of 2 3.7.3 Hold panel for 1 h at -40 C, then expose for 1 h at 99 +/- 2 C. Repeat for 4 cycles. Maximum shrinkage 5%. Adhesion - 180 Plane 825 N/m width 3.7.4 Weathering Resistance, min 225 kJ (SAE J1885) Adhesion - 180 Peel 600 N/m width 3.8 FOGGING (FLTM BO 116-03) Fog Number, min 60 The formation of droplets or coalescence into a clear film is cause for rejection. 3.9 LABEL STRENGTH During installation, the label must not break, tear or deface. The release backing shall not tear or delaminate while being removed from the label.

展开阅读全文
相关资源
猜你喜欢
  • DIN EN 10120-2008 Steel sheet and strip for welded gas cylinders German version EN 10120 2008《焊接气罐薄钢板材和带材》.pdf DIN EN 10120-2008 Steel sheet and strip for welded gas cylinders German version EN 10120 2008《焊接气罐薄钢板材和带材》.pdf
  • DIN EN 1013-2015 Light transmitting single skin profiled plastics sheets for internal and external roofs walls and ceilings - Requirements and test methods German version EN 1013 2.pdf DIN EN 1013-2015 Light transmitting single skin profiled plastics sheets for internal and external roofs walls and ceilings - Requirements and test methods German version EN 1013 2.pdf
  • DIN EN 10130 Berichtigung 1-2007 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions German version EN 10130 2006 Corrigenda to DIN EN 10130.pdf DIN EN 10130 Berichtigung 1-2007 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions German version EN 10130 2006 Corrigenda to DIN EN 10130.pdf
  • DIN EN 10130-2007 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions English version of DIN EN 10130 2007-02《冷成形用冷轧低碳钢平板产品 技术交货条件》.pdf DIN EN 10130-2007 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions English version of DIN EN 10130 2007-02《冷成形用冷轧低碳钢平板产品 技术交货条件》.pdf
  • DIN EN 10131-2006 Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimen2.pdf DIN EN 10131-2006 Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimen2.pdf
  • DIN EN 10132-1-2000 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 1 General German version EN 10132-1 2000《热处理用冷轧窄钢带材 交货技术条件 第1部分 总则》.pdf DIN EN 10132-1-2000 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 1 General German version EN 10132-1 2000《热处理用冷轧窄钢带材 交货技术条件 第1部分 总则》.pdf
  • DIN EN 10132-2-2000 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 2 Case hardening steels German version EN 10132-2 2000《热处理用冷轧窄钢带材 交货技术条.pdf DIN EN 10132-2-2000 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 2 Case hardening steels German version EN 10132-2 2000《热处理用冷轧窄钢带材 交货技术条.pdf
  • DIN EN 10132-3-2000 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 3 Steels for quenching and tempering German version EN 10132-3 2000《热处理.pdf DIN EN 10132-3-2000 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 3 Steels for quenching and tempering German version EN 10132-3 2000《热处理.pdf
  • DIN EN 10132-4-2003 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 4 Spring steels and other applications German version EN 10132-4 2000 +.pdf DIN EN 10132-4-2003 Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 4 Spring steels and other applications German version EN 10132-4 2000 +.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1