FORD WSS-M28P1-B1-2017 GLASS PERFORMANCE SAFETY FLOAT LAMINATED FOR WINDSHIELDS TO BE USED WITH FORD WSS-M99P1111-A .pdf

上传人:jobexamine331 文档编号:752613 上传时间:2019-01-14 格式:PDF 页数:23 大小:280.40KB
下载 相关 举报
FORD WSS-M28P1-B1-2017 GLASS PERFORMANCE SAFETY FLOAT LAMINATED FOR WINDSHIELDS  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第1页
第1页 / 共23页
FORD WSS-M28P1-B1-2017 GLASS PERFORMANCE SAFETY FLOAT LAMINATED FOR WINDSHIELDS  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第2页
第2页 / 共23页
FORD WSS-M28P1-B1-2017 GLASS PERFORMANCE SAFETY FLOAT LAMINATED FOR WINDSHIELDS  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第3页
第3页 / 共23页
FORD WSS-M28P1-B1-2017 GLASS PERFORMANCE SAFETY FLOAT LAMINATED FOR WINDSHIELDS  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第4页
第4页 / 共23页
FORD WSS-M28P1-B1-2017 GLASS PERFORMANCE SAFETY FLOAT LAMINATED FOR WINDSHIELDS  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第5页
第5页 / 共23页
点击查看更多>>
资源描述

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 07 2017 07 24 Revised See Summary of Revisions for Details P. Konopka NA 2015 06 29 Revised See Summary of Revisions for Details J. Crist, NA 1996 11 04 Activated B1 B5: 1996 11 04. B6 and B7: 2008 02 07 W. Curtiss/W. Scholz Controlled d

2、ocument at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 24 GLASS, PERFORMANCE, SAFETY, FLOAT LAMINATED WSS-M28P1-B1 FOR WINDSHIELDS LAMINATED FOR SIDE GLASS AND BACKLITES WSS-M28P1-B2 LAMINATED FOR ALL OTHER GLASS APPLICATIONS WSS-M28P1-B3 TEMPERED FOR SIDE GLASS AND BACKLITES WS

3、S-M28P1-B4 TEMPERED FOR ALL OTHER GLASS APPLICATIONS WSS-M28P1-B5 POLYCARBONATE (PC) COATED, FOR SIDE GLAZING AND BACKLITES WSS-M28P1-B6 POLYCARBONATE (PC) COATED, FOR ALL OTHER GLAZING APPLICATIONS WSS-M28P1-B7 1. SCOPE The following specifications define performance requirements for: B1 - Laminate

4、d products for windshields. B2 - Laminated products used in areas such as side glass and backlites. B3 - Laminated products used anywhere driver visibility is not a concern such as roof glazing or behind the B pillar on trucks. B4 - Tempered products used in areas such as side glass and backlites. B

5、5 - Tempered products used anywhere driver visibility is not a concern such as roof glazing or behind the B pillar on trucks. B6 - Polycarbonate (PC) coated products used in areas such as fixed side glazing and fixed backlites. B7 - Polycarbonate (PC) coated products used anywhere driver visibility

6、is not a concern such as fixed roof glazing or behind the B pillar on trucks. 2. APPLICATION These specifications were released originally for processed safety glazing that meet all Governmental and other standards (reference para 3.8) used for glazing motor vehicles. 3. REQUIREMENTS 3.1 APPROVED SO

7、URCES This specification is performance based and does not have approved sources. All test plaques must go through process conditions identical to that of final production parts. 3.4 APPEARANCE Automotive windows are defined as “appearance items“ according to AIAG (Automotive Institute Action Group)

8、 Production Part Approval Process (PPAP). This requires that adequate approval of appearance criteria must be defined and adhered to. Since this specification is the sole definition of such criteria, adherence to it satisfies the intent of PPAP Appearance Item Requirements, therefore, no additional

9、appearance approval reporting is required. ENGINEERING MATERIAL SPECIFICATION WSS-M28P1-B1/B7 Copyright 2017, Ford Global Technologies, LLC Page 2 of 23 3.5 TRADEMARK The trademark shall meet all criteria of the local or intended market requirements and shall include any additional information requi

10、red by the country of intended use. The trademark shall be legible from inside or outside the vehicle and the location of the trademark shall be designated and/or approved by all responsible activities of the Ford Motor Company. The trademark location shall be shown on the engineering drawing. The t

11、rademark may be applied using ceramic coatings in glass or via a printing, laser part marking, tool marking, film lamination, or film insert molding (FIM) procedure in polycarbonate. In the case of polycarbonate glazing, the method or methods allowable shall be specified on the engineering document.

12、 Reference: RQT-011101-12080, RQT-001800-004030 1.0 mm dia. (6 allowed), no more than 6 total for backlites and quarter windows, 150 mm separation. Adhesion chips are not allowed. Bloom Not allowed Bulls eyes Permitted if not visible at in vehicle position Dig/rub Not allowed Etch mark, crush Not al

13、lowed Optical distortion Distortion permitted within 10 mm of paint edge, otherwise must be approved by boundary sample review and signoff. ENGINEERING MATERIAL SPECIFICATION WSS-M28P1-B1/B7 Copyright 2017, Ford Global Technologies, LLC Page 4 of 23 Area A Area B Lint (laminated Heavy 0.5-5.0 mm and

14、 Medium 10.1-20.0 mm no more than 2 in a 305 mm dia.; Medium 3.0-10.0 mm and Light 20.1-40.0 mm no more than 3 in a 305 mm dia.; Light 6.0-20.0 no more than 4 in a 305 mm dia. Edge Treatment (Shiners, etc.) Refer to SAE J673 for glass edge definition. Specific edge requirements identified on part dr

15、awing. Tool marks, including mold marks, cloth marks, screen marks, and tong marks. Not allowed Not allowed unless agreed upon in approved boundary sample Water stain Not allowed 3.12.2 Vinyl Defects for Laminated Glass Products (B1, B2, along the edge closest to the “C“ region, a smear protruding 2

16、 mm is allowed Incorrect Print Dots The incomplete printing of the 1.0 x 6.0 mm allowed, 305 mm separation. ENGINEERING MATERIAL SPECIFICATION WSS-M28P1-B1/B7 Copyright 2017, Ford Global Technologies, LLC Page 7 of 23 missing or run together desired image on the surface of a part reference Design Ru

17、le FX-011100-0012 Defect Definition of Defect Acceptance Criteria Edge of print not consistent Printing edge has inconsistent smoothness and straightness Saw tooth 0.5 mm peak height permitted, 0.5 to 1.0 permitted over 150 mm length per edge Grid Color Variations in color due to silver on different

18、 surfaces are acceptable. Defect Definition of Defect Acceptance Criteria Bus bar visibility through decoration layer Not allowed Discoloration from heater grid, antenna, bus bar Discoloration of bus typically due to oxidation. Not allowed on blackout area Allowed on bus bar due to oxidation Silver

19、void on heater grid, antenna, or bus bar Allowable only if not visible from outside of vehicle and part performance is not affected. May be repaired (touch ups) if void is less than 3 mm in diameter and part performance is not affected post touch up. 3.12.5.4 Polycarbonate Decoration Defects (Laser,

20、 Tool obscuration, Film Insert Molding or Lamination) Defect Definition of Defect Acceptance Criteria Coating defect over laser decoration Delamination or cracking of coating with genesis from the edge of the laser part mark. This may occur when laser part marking occurs after coating procedure and

21、the laser power is too high. No damage to coating system that exceeds 0.1mm from edge of laser mark. Coating defect over tool marking Coating drips, runs, and or build up due coating over laser part marking. This may occur when laser part marking occurs before coating procedure No drips, build up, o

22、r run visible in area “A” or “B”. Defects in the “C” area are allowed, so long as they do not result in cracking or delamination of coating. Wrinkling of Film Film folds or wrinkles during the manufacturing process, resulting in wrinkled lines in the in the glazing piece. Not allowed in “A” and “B”

23、areas Film Delamination Film delaminates from PC substrate or coating delaminates from film Not allowed in any area. Air, oil, or moisture Penetration (bubbles) Air, oil, or water pockets trapped underneath film. None allowed in areas “A” and “B”. For area “C” 1.5mm diameter allowed. Dirt/foreign Ma

24、terial Dirt or foreign material stuck between the film and the PC. Area “A“: not allowed Area B: 1.5 mm, 305 mm separation Area C: 1.5 mm, 305 mm separation 3.12.6 Optical Defects All types of optical defects (e.g. bulls eyes, cloth marks, and ripple) shall be inspected using a point source light (s

25、ee Glossary) as shown in Figure D1. The test part is mounted at vehicle installation angle and is located between the point source light and a white projection board so that the projected light passes through the glazing before reaching the projection board. The total distance between the point sour

26、ce light and projection board is 8m, with the test part is halfway between. The test part (excluding backlites) is rotated around its vertical axis as needed to simulate views from the side. The inspector observes the ENGINEERING MATERIAL SPECIFICATION WSS-M28P1-B1/B7 Copyright 2017, Ford Global Tec

27、hnologies, LLC Page 8 of 23 projected image and reports the part unacceptable if variations in the brightness of the projected image are extreme. A photograph of the projected image will be required for some reports. Figure D1. Point source light test. When the point source image is hard to interpre

28、t, the test part is also inspected using the zebra test, as shown in Figure D2. The test part is mounted at vehicle installation angle and is located between the inspector and a zebra board (see Glossary) so that the inspector can see the appearance of the stripes through the test part. The total di

29、stance between inspector and the zebra board is 8m, and the test part is halfway between. The test part (excluding backlites) is rotated around its vertical axis as needed to simulate views from the side (cross car). The inspector observes the apparent shape of the stripes and reports the part unacc

30、eptable if any of the stripes appear excessively wavy. A photograph of the zebra board through the test part will be required for some reports. Figure D2. Zebra test. 3.13 OBSCURATION AND PRINTING IN GLAZING 3.13.1 Glass Ceramic Coatings Decorative ceramic coatings (ceramic frits) must meet all requ

31、irements of WSS-M99P6-C1/C2 (most current version) and be chosen from the Ford Approved Source list (ASL). They must also be specified on the engineering drawing. Conductive coatings, such as painted antennas and heated grids for backlites, must meet all requirements of WSB-M12P2-B/B2 (most current

32、version) and be chosen from the Ford Approved Source list (ASL). They must also be specified on the engineering drawing. The Tier 1 supplier must meet all USCAR-40 Lead Free Solder Validation Test Plan requirements with new lead free terminals. Any deviations must be approved by Core Glass Engineeri

33、ng. Electrically heated glass must also conform to all SDS requirements. ENGINEERING MATERIAL SPECIFICATION WSS-M28P1-B1/B7 Copyright 2017, Ford Global Technologies, LLC Page 9 of 23 3.13.2 Polycarbonate Conductive inks and pastes the following are references for performance: Conductive pastes, such

34、 as printed antennas and heated grids for backlites, must meet all requirements of WSB-M12P2-B/B2 (most current version). EHBs (electrically heated backlites) must also conform to all applicable SDS requirements. 3.13.3 Ceramic Frits Ceramic frit shall be as specified on the engineering drawing. Mat

35、erials supplied shall meet WSS-M99P6-C1/C2 (most current version), be chosen from the Ford Approved Source List (ASL) and meet all the requirements listed below. 3.13.3.1 Opacity The measurement shall be made using a transmission black and white densitometer e.g. “Tobias Model TBX” or similar, in di

36、rect contact with the coating surface. For items B1, B2, B3, B4, B5, B6 UV light transmission must be less than 0.1% (UV absorption must be greater than 99.9%). 3.13.3.2 Color (FLTM BI 109-01 Visual Assessment, SAE J1545, Three-Angle CMC) Color shall match the Master Approved Sample color panel or t

37、he initial sample as approved by Design Center, if applicable. Ceramic frits shall be as specified on the engineering drawing. Materials supplied shall meet all the requirements listed in those specifications. 3.13.3.3 Ceramic Frit Thickness (ASTM B 487, Non-Metallic Substrates) Coating thickness mu

38、st be sufficient to meet all requirements of this material specification. Refer to mutually agreed upon control plan. 3.13.3.4 Ceramic Frit Adhesion WSS-M99P6-C1/C2 Adhesion, max Grade 2 (FLTM BI 106-01, Method B, new knife only), part should be tested in the coating ink/paint configuration as speci

39、fied on the engineering drawing. 3.14 POLYVINYL BUTYRAL FOR LAMINATED PRODUCTS (B1, B2 and B3) Polyvinyl butyral with or without gradient band shall be as specified on the engineering drawing. Tolerances shall be as specified in the material specifications or on the engineering drawing. 3.14.1 Vinyl

40、 Adhesion Pummel Test Pummel value 3-6 Pummel Adhesion Procedure FLTM BU 158-01 This test is conducted to determine the bond between the glass and the vinyl on laminated products. This test is typically used for process control within each plant. Additionally, laminated products with any coating on

41、either of the two inner surfaces must maintain a pummel adhesion value between 3 and 6 after being exposed to the weathering conditions of section 3.16. ENGINEERING MATERIAL SPECIFICATION WSS-M28P1-B1/B7 Copyright 2017, Ford Global Technologies, LLC Page 10 of 23 3.14.2 Bake Test The Bake test is a

42、check for laminate de-airing and moisture content, that if not within correct limits, may lead to in service bubble formation within the PVB or “ice crystal” formation. Acoustic PVB is more susceptible to this failure mode than normal PVB. Bake testing is considered a non-destructive test that shoul

43、d not be performed prior to 48 hours after the initial autoclave process to allow the parts to normalize. This test is to be conducted on a full laminated part for initial qualification and shall be tested as specified in the control plan and includes all parts up to and including the PPAP phases. T

44、he bake test shall be repeated for glass thickness changes, glass bending changes, lamination process changes, manufacturing line changes, and PVB changes or as determined by Engineering/STA. Bake parts for 2hrs at 100C and then inspect for bubbles per the most current version of the ANSI Z26.1. Par

45、ts to be tested may be cut to fit the test chamber as long as the entire laminated part is tested. Bake Test inspection criteria (reference section 5.5). Any parts not meeting the ANSI Z26 specification are considered failed and the lamination process must be revised and revalidated by this test. An

46、 alternative is to autoclave bake test the parts at ambient pressure (14 psi / 96 kPa). A stair step bake test must be performed on an initial qualification part (1 part) and when process parameters are varied from the initial validation. The stair step bake test consists of baking the same part at 110C, 120C, 130C, 140C, 3.1, 3.2, 3.3, 3.19 3.7, 3.8, table in 3.12.3, 3.12.4, table in 3.12.4, 3.15.1, 3.16, 3.17.3, 3.18.10 subtitle, 5.1, 5.3 & 5.7 revised

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1