FORD WSS-M3H180-A1-2017 CARPET POLYESTER NON WOVEN FLAT NEEDLED FUSED BACK 250 g m2 (7 4 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf

上传人:twoload295 文档编号:753370 上传时间:2019-01-14 格式:PDF 页数:4 大小:53.97KB
下载 相关 举报
FORD WSS-M3H180-A1-2017 CARPET POLYESTER NON WOVEN FLAT NEEDLED FUSED BACK 250 g m2 (7 4 oz) NOMINAL FACE  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第1页
第1页 / 共4页
FORD WSS-M3H180-A1-2017 CARPET POLYESTER NON WOVEN FLAT NEEDLED FUSED BACK 250 g m2 (7 4 oz) NOMINAL FACE  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第2页
第2页 / 共4页
FORD WSS-M3H180-A1-2017 CARPET POLYESTER NON WOVEN FLAT NEEDLED FUSED BACK 250 g m2 (7 4 oz) NOMINAL FACE  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第3页
第3页 / 共4页
FORD WSS-M3H180-A1-2017 CARPET POLYESTER NON WOVEN FLAT NEEDLED FUSED BACK 250 g m2 (7 4 oz) NOMINAL FACE  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 0 2017 03 20 Released L. Wu, AP Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 4 CARPET, POLYESTER, NON WOVEN, FLAT NEEDLED, WSS-M3H180-A1 FUSED BACK, 250 g/m2 (7.4 oz) NOMINAL FACE 1. SCOPE The ma

2、terials defined by this specification are flat needle, non-woven polyester carpets of good quality and uniform composition. A low melt polyester binder forms the backing and the carpet face is made with virgin fiber. 2. APPLICATION This specification was originally released for Ford Focus MY17 5Door

3、 Package Tray. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is

4、located within Ford at or available externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the

5、material should occur in the conditioning environment or soon after removal. 3.3 PERFORMANCE CRITERIA 3.3.1 In addition to the requirements listed herein, the end-item carpet shall be tested to WSS-M15P6-E and any additional SDS requirements. The details for each of the supplier specific constructio

6、ns shall be documented in the supplement attached and uploaded into the scanned data package. 3.3.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/ latest. Data must be p

7、rovided at the appropriate program milestone. 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished roll goods (including substrate layers) prior to any subsequent operations, such as molding. 3.5 APPEARANCE The color, pattern, and gloss shall match the approv

8、ed Corporate Design master sample. ENGINEERING MATERIAL SPECIFICATION WSS-M3H180-A1 Copyright 2017, Ford Global Technologies, LLC Page 2 of 4 3.6 COMPOSITION 3.6.1 Face Fiber 95% Polyester (ASTM D276) 3.6.2 Binder Fiber 5% Low Melt (ASTM D276) Polyester 3.7 METHOD OF DYEING Solution dyed 3.8 CONSTRU

9、CTION 3.8.1 Face Fiber 6 Denier (ASTM D 1244) 3.8.1 Binder Fiber 4 Denier (ASTM D 1244) 3.9 THICKNESS* 2.0 +/- 0.5 mm (ISO 1765) *Face thickness prior to molding. 3.10 WEIGHT 3.10.1 Face Fiber 225 - 275 g/m2 (ASTM D5848) (6.6 8.1) oz 4. GENERAL INFORMATION This information given below is provided fo

10、r clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 DRAWING CALL OUT The following shall be called out on the Engineering drawing to correctly designate the approved material. WSS-M3H180-A1 Suppl

11、ier Name and Product Code (As it appears on the Approved Source Listing) WSS-M15P6-E 4.2 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall sub

12、mit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a min

13、imum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.3 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material

14、upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the ENGINEERING MATERIAL SPECIFICATION WSS-M3H180-A1 Copyright 2017,

15、 Ford Global Technologies, LLC Page 3 of 4 affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineer

16、ing Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.4 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations o

17、r Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or

18、GMAP reporting. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATION WSS-M3H180-A1 Copyright 2017, Ford Global Technologies, LLC Page 4 of 4 Non Woven Carpet Construction Supplement Supplier _Supplier Contact Name_ Number _ Product/ Style Name _ Material Specification _ Performance Specificati

19、on _ Supplier Product Code _ Manufacturing Location _ Supplier Lab Number _ Supplier Lab Date _ Composition Type Supplier Face Fiber ASTM D276 _ _ Binder Fiber ASTM D276 _ _ Fabric Backing ASTM D276 _ _ Pre Coat ASTM D276 _ _ Primary Backing ASTM D276 _ _ Secondary Backing ASTM D276 _ _ Construction

20、 Solution or piece dyed (circle one) % Recycled (PIR/PCR) _ Denier _ Filament Count _ Face Fiber Thickness ISO 1765 _+/- _ mm Binder Fiber Thickness ISO 1765 _+/- _ mm Pre Coating Thickness ISO 1765 _+/- _ mm Primary Thickness ISO 1765 _+/- _ mm Secondary Thickness ISO 1765 _+/- _ mm Mass per Unit Area Weight Face Fiber ASTM D5848 _+/- _ g/m2 Binder Fiber ASTM D5848 _+/- _ g/m2 Pre Coating ASTM D5848 _+/- _ g/m2 Primary Backing ASTM D5848 _+/- _ g/m2 Secondary Backing ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Rolled Goods _ Molded Product _

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1