1、ADAM OPEL AGTDCCentral LaboratoriesTECHN. LIEFERBEDINGUNGENFR WERKSTOFFEENGINEERINGMATERIAL SPECIFICATIONLIMITED USEQK 001210Polyamid 66 mit PARA - Fasern /Polyamide 66 with PARA - FibresNote: This standard may be applied only for current programs. It is inactive for all future projects andwithout r
2、eplacement.If this product should be used for a new project, a Re-Certification according to GMW15702 is required.Hinweis: Diese Spezifikation darf nur noch fr laufende Projekte angewendet werden und ist fr allezuknftigen Projekte ohne Ersatz ungltig.Falls dieses Produkt fr ein neues Projekt zum Ein
3、satz kommen soll, ist eine Neu-Zertifizierung nachGMW15702 erforderlich.Werkstoff: Polyamid 66 mit 20 Massenanteill in % PolyarylamidfasernMaterial: Polyamide 66 with 20 % by mass polyarylamide fibresKurzzeichen: PA 66 + PARA Symbol:Verwendung: Spritzgietype zur Herstellung technischer Teile mit hoh
4、er Verschleifestigkeitauch bei hohen Temperaturen, z.B. Lagerbuchse - PedalApplication: Injection moulding type for manufacturing technical parts with high wearresistance also at high temperatures, e.g. Bush - pedalHandelsname: Zytel 70K20Trade Name:Lieferant: Du Pont de Nemours (Deutschland) GmbH,
5、D - 61343 Bad HomburgSupplier:Lieferform: GranulatForm of Delivery: GranulesAusfertigungs-Nr.:Issue: 2Datum:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approved: MKSeite vonPage 1 of 4Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprfungen trgt der Lieferant die Verantwortung dafr,
6、 da die gelieferteWare die Opel-Zeichnungsvorschriften erfllt. Ein Prfbericht mit zahlenmigen Ergebnissen aus Prfungen der Lieferung selbst ist bei jederBemusterung, Erstbelieferung und Ausfhrungsnderung mitzugeben.Despite spot checks possibly performed by Opel, it is the suppliers responsibility th
7、at the delivered parts are in line with the Opel drawings.Deliveries of samples, first off-tool parts and parts, whose performance has been changed, must be accompanied by a test report showing thetest results in terms of figures.LBSP TL WS 1 11/95LIMITED USE QK 001210Ausfertigungs-Nr.:Issue: 2Datum
8、:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approved: MKSeite vonPage 2 of 4Forderungen / Requirementsa) zu dokumentierende Eigenschaften / values for documentationDichte DIN 53 479Density (1,2 0,05) g/cm3Elastizittsmodul aus dem ISO 1783-Punkt-BiegeversuchModulus of Elasticity by the3 -Point-Fle
9、xural Test 4730 N/mm2Kerbschlagzhigkeit ISO 180 / 1ANotched Impact Strength 4,5 kJ/m2Formbestndigkeit in der Wrme ISO 75-2Temperature of Deflection under LoadVerfahren/Method A 216 CReifestigkeit ISO 527Tensile Strength at Break 110 MPab) nur zur Information / only for informationSchmelztemperaturMe
10、lt Temperature 255 CFormbestndigkeit in der Wrme ISO 75-2Temperature of Deflection under LoadVerfahren/Method B 252 CReidehnung ISO 527Elongation at Break 5 %Kerbschlagzhigkeit ISO 179 / 1eANotched Impact Strength 50 kJ/m2Thermischer Lngenausdehnungs- DIN 53 752koeffizientCoefficient of linear Therm
11、al Expansionlngs / longitudinal 6 . 10-5 1/Kquer / transverse 10 . 10-5 1/KLIMITED USE QK 001210Ausfertigungs-Nr.:Issue: 2Datum:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approved: MKSeite vonPage 3 of 4Umweltschutz / Environmental Protectionnach / to QU 000 001 - Cadmium.Hinweis / ReferenceWeite
12、re Informationen siehe QK 000 000. /For further information refer to QK 000 000.Bemerkung / NoteAlle Probekrper werden im Spritzgieverfahren hergestellt. Alle Werte werden an spritztrockenenProbekrpern ermittelt (spritztrocken = Wassergehalt 0,2 Massenanteil in %). /All test pieces shall be manufact
13、ured by injection moulding. All values shall be determined on dry asmoulded test pieces (dry as moulded = water content 0,2 % by mass).Abfallbeseitigung / Waste DisposalGruppe D, Opel-Betriebsrichtlinie Nr. 440Achtung! Bei unkontrollierter thermischer Zersetzung Bildung von giftigen Abbauprodukten.
14、/Group D, Opel-Plant Directive No. 440Attention! Uncontrolled thermal decomposition gives poisonous decomposition products.LIMITED USE QK 001210Ausfertigungs-Nr.:Issue: 2Datum:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approved: MKSeite vonPage 4 of 422.10.2014War Ausfertigungs-Nr. 1, Datum 08/94Limited Use StatusWas Issue No. 1, Date 08/94Limited Use StatusDatumDateBeschreibung / Description GeprftCheckedGenehmigtAppd.nderungen / Revisions