1、 ENGINEERING STANDARDS Material Specification LIMITED USE EDS-M-8511 Sealing Compound Do Not Use on New Program; No Replacement. 6d* GF,p Note: 8 E:48t G8 =97 FF7 957%L+ , FG P-P Program 72P# 957%L: 6#$ . Copyright 2011 General Motors Company All Rights Reserved June 2011 Originating Department: GM
2、Korea Engineering Standards Page 1 of 5 Version : 5 1 Scope 1.1 Purpose. This specification specifies the general requirements of sealing compound used for automobile. 1.2 Material Description. Solvent contained sealing compound, difficult to inflame, on rubber base. 1.3 Typical Applications. This s
3、pecification applies to the sealing compound for sealing used for welding point of automobile body in painting progress of automobile. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifi
4、cations. EDS-M-0102 EDS-T-7777 EDS-T-7786 EDS-T-7902 GMW3059 2.3 Additional References. TMC003 Material Safety Data Sheet guidance documents 3 Requirements 3.1 General Properties. 1 P7 1.1 +95 . ., E:48t 8% =7 957%L# 6d* GF,p8 8-L958 7 ?7 $4F7 9IF$ . 1.2 8: 8-L C2e . Rubber :02e.7 Solvent* E FF , 8-
5、L958 $8)9I4 !7$2e8 2e:8x .(8# Sealing Compound. 1.3 957 -88 . ., E:48t 8% =8 $8 )9I4 , 8% = =8 79E.88 Sealing 7 17F# Seailing Compound 8 8-L958 7 ?7 $4F7 9IF$ . 2 4) E:4 / :0 : C-H +d%P 9I8 6# F 48 07 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.2 GM E:4 / . EDS-M-0102 EDS-T-7777 EDS-T-7786 EDS-T-7902 G
6、MW3059 2.3 dA E:4 / . TMC003 Material Safety Data Sheet guidance documents 3 7 1F 3.1 d., ,p2e . Table 1: General Properties / E 1: d., ,p2e Designations / 4G F+ Test Methods / 4G - Specifications / 3.1.1 Cure Condition. / G9 . Heat treatment condition of painting system in GM Korea. / GM Korea $8 7
7、(=* 9 . 3.1.2 Surface to be Applied. / 957E+ Rough steel sheet or zinc-coated steel sheet. / Rough IDD Gm8t 6x7$ $6 Sealant * G4A$ . 3.2.2.3 G4 ! Sealant * 17: -!4A$ . 3.2.2.4 Sealant4 177 $*+ 80 E u 120 48 98p) -?F$ . GM KOREA ENGINEERING STANDARDS EDS-M-8511 Copyright 2011 General Motors Company A
8、ll Rights Reserved June 2011 Page 3 of 5 Version : 5 3.2.2.5 Observe the condition of sealant. 3.2.3 Low Temperature Resistance. 3.2.3.1 Harden the sealant with condition of clause 3.1.1, and place the steel sheet at (-20) E for 16hours, and then bend it at (-20) E for 5 seconds using the 70 mm of s
9、pindle. 3.2.3.2 Check the adhered surfaces whether peel off or not. 3.3 Workability. From bundles and large tin can by means of pump (ratio 10 : 1) with pressure stamp, over ring line or stub line, tube and thread-or spray gun with corresponding nozzle. 4 Manufacturing Process Not applicable. 5 Rule
10、s and Regulations 5.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the Korean and English language, the Korean language shall take precedence. 5.3 Inspection and Rej
11、ection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by the responsible Engineering department prior to commencement of delivery of bulk supplies. A new approval must be rec
12、eived for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It is the responsibility of the supplier to inform the customer in a timely manner, without so
13、licitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier prior to commencement of delivery of non-conforming bulk supplies. In individual cas
14、es, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Initial Source Approval. No shipments shall be made by any supplier until representative initial production samples have been approved by the appropriate Materials Engineering department(s) as me
15、eting the requirements of this specification. 3.2.2.5 9E=9P8 1B* 4=dF$ . 3.2.3 !F2e 4G . 3.2.3.1 4.1F8 G9 G (-20) E u 16 48 -? G 70 mm Spindle 8x 87F7 , (-20) E72P 58 88x 7 , F6* 72T8p) F$ . 5.3 1 -C -L)X . GM 8-LE:47 8F 9P%P .E8! 8*8 4G D8t ., 8-LE:47 9I%P 4G 8x 7 98x +94P6 F+ , 61 )= 987 :04 .2P8
16、388x -O6x6 F$ . &H88 , d# , 22e , 9P9 )9I ,* /D# 21: &%0 4)%P 6&F -8($ -P2%T 7 , 1)7 388x -O6x6 F$ . $* F84 6# F , 8-L958p) 4 4=8x F6 F$ . -$8 GE84 6# F , )=8# 38%L: 68t 9PE8 61 )= 987 +& F$- 4G 8x -L.) 3LFF 0* ,l2PGF6 F$ . 8. 77 86 :04 .2P7t )=888 F87 8F $%P : 4G 8x 44F 3L 8$ . 5.4 FF2P# 6| %P$ . G
17、M KOREA ENGINEERING STANDARDS EDS-M-8511 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 4 of 5 Version : 5 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition of an existing product has occurre
18、d, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be
19、 in compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 5.7 Dont dump in a dit
20、ch, drain, and river. 6 Approved Sources Engineering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials File under this standard number have been qualified by Engineering as meeting the requirements of this standard. For other GM locations, t
21、he responsible Engineering group should be contacted to obtain the approved source in that individual country. 6.1 Approval Material. 5.5 ,p:6|98.(8* / 6|98.(8* (MSDS/SDS). 49PE8 )= D# d97 )=%L# 9PE ! GF,p: 92e8 -%P 7 , GF ,p: .* y E47 4F 2l 9G 43B (GHS) D# 5 :7!- ,p:6|98.(8* / 6|98.(8* 7 1F8x +9F#
22、,p:6|98.(8* / 6|98.(8* 9PF6+ F$ . 4958p) 9PE8 ,p:6|98.(8* / 6|98.(8*# GM8 ,p:6|98.(8* / 6|98.(8*7 4F :?8 TMC0038 7 1F8x :43LF6+ F$ . 5.6 ., E:47 9P4%P +& 8:&8t GMW3059 (8TF,p: 179P )8 9P* &d(6 F$ . 5.7 F3L , -d3L , I7 -*: + . 6 38 6= 8 E:48t 38%P 6=7 $4F d3T95 :8x 7F$ . 8 E:47 8F d3T958 :8 7x*%P GM
23、88 +2l7 !7(%P 6=+8 8 E:48 7 1F8x 94A$ . $* :7!7 88?F GM 8 7 , F$- 4-) 38%P 6= 9I.(* 83LFd 88F2P# F$- :04 .2P7t GE8F6 F$ . 6.1 38 8* . Part No. Old P/No. Approved Supplier / 38 6= Approved Raw Material / 38 88* Remarks / /x 94545132 M-8511 Korea Sunstar Chemical. / 82eGF M-8511 6.2 Approval and Quali
24、ty Assurance Procedure. All raw materials shall be approved and regularly inspected for its quality prior to and during mass production delivery according to approval and quality assurance procedure for chemical raw materials (Spec. No. EDS-M-0102). 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms
25、, Abbreviations, and Symbols. GHS Globally Harmonized System MSDS Material Safety Data Sheet SDS Safety Data Sheet 6.2 38 -C E:.(: 9) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 5 JUN 2011 Apply new Engineering Standard Template. Limited use with no replacement (Polymer / Organic Material Lab Team) / 4 d3TE:4 64 957 . F9I957 ($4=E:4 68 ) =* (G)8*4G D4 )
