1、 ENGINEERING STANDARDS Test Procedure LIMITED USE EDS-T-2111 Flywheel and Pressure Plate Do Not Use on New Program; No Replacement. F(8 HT0 6)YDD8 E+?U9I Note: 8 E:48t G8 =97 FF7 957%L+ , FG P-P Program 72P# 957%L: 6#$ . Copyright 2011 General Motors Company All Rights Reserved December 2011 Origina
2、ting Department: GM Korea Engineering Standards Page 1 of 3 Version : 4 1 Scope Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the Korean and English language, the Korean language shall take precedence. 1.1 Purpose and Applicability.
3、 The purpose of this standard is to measure peak-to-valley height and contour of the frictional surfaces of flywheel and pressure plate. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. None 2.2 GM Standards/Speci
4、fications. None 2.3 Additional References. None 3 Resources 3.1 Equipment. 3.1.1 Surface Measuring Device. 4 Procedures 4.1 Preparation. 4.1.1 Clean flywheel and pressure plate with appropriate solvent. 4.1.2 Mark the point on flywheel and pressure plate at which measurements are to be taken. 4.2 Co
5、nditions. 4.2.1 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 1 P7 :0 : ., E:48 6,:8 19IE D?7t 9472P 5-;,:8 ;d8 E D?8 =8 ). 5.2.2.3 Ra. :E4 2T D ?d (?d 2T72P
6、 d:4 l8!8 D2T8p).Bd ?d 8X18 -6!7 $4F 13T DF ). 6 6|987 $4F 7 9 ., E:48t 88G ,p: , 86 , 8/x &%8x E FF 3L 8$ . ., E:48t 87 $4F 170 4)%P +& 6|98 ,l9P8 F8x 9P4F:# 6#$ . &d(2P 17 987 95FF 6|980 I 1B* 9DF , -18 9PF 728 957 7 .* 9IF# 8t ., E:4 1788 =y8 1F8$ . 7 768 9I8 7.1 98,l 76 . F$-1F 68 . 7.2 66 -C dG
7、l . F$-1F 68 . 8 Ed - $* ,l2P! $+ &%72P ., E:48 87%T &# $80 M8 EdF$ . Test to EDS-T-2111 GM KOREA ENGINEERING STANDARDS EDS-T-2111 Copyright 2011 General Motors Company All Rights Reserved December 2011 Page 3 of 3 Version : 4 9 Release and Revisions This standard was originated in January 1996. It
8、was first approved by Engineering Standard Committee in January 1996. It was first published in January 1996. 9 9P9I -C P9I 8)Y ., E:48t 1996 “x 1 87 E:4 -Gl4 .7 %L6 , d3TE:41,h7 8F 1996“x 187 38%L6$ . ., E:48t 1996“x 187 ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 4 DEC 2011 Apply new Engineering Standard Template. Limited use with no replacement (TM Test & Validation PMT Team) / 4 d3TE:4 64 957 . F9I957 ($4=E:4 68 ) =* (-2dP-P4G :D4 )
