GMKOREA EDS-T-7010-2012 Test Method for Organic Coatings on Plastic Parts.pdf
《GMKOREA EDS-T-7010-2012 Test Method for Organic Coatings on Plastic Parts.pdf》由会员分享,可在线阅读,更多相关《GMKOREA EDS-T-7010-2012 Test Method for Organic Coatings on Plastic Parts.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING STANDARDS General Specification SUPERCEDED EDS-T-7010 Test Method for Organic Coatings on Plastic Parts This standard may be applied only for current projects. It is Superceded for all future projects and replaced by GMW14797. F(3D% 2:8 8Td$8+ 4G - Note: 8 E:48t G8 =97 FF7 957%L+ , FG P
2、-P Program .Bd# GMW14797 ) $4=F7 957F$ . Copyright 2012 General Motors Company All Rights Reserved March 2012 Originating Department: GM Korea Engineering Standards Page 1 of 7 Version : 8 1 Introduction Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of
3、 conflict between the Korean and English language, the Korean language shall take precedence. 1.1 Purpose. This specification details the performance requirements for applied organic surface coatings on plastic parts and components, used for either interior or exterior applications on motor vehicles
4、. 1.2 Scope. 5 types of requirement are specified dependent upon the severity of service operation of the component. 1.2.1 Type A1. It is applicable to surface finishes used on the external body and on external components in areas of severe service operations e. g. below the WL-line (Fascia bumper,
5、Radiator grille, MOLDG R/PNL, CVR towing eye etc.) 1.2.2 Type A2. It is applicable to surface finishes used on the external body and on external components in areas of normal service operations e.g. above the WL-line. (Handle trunk lid, OSRVM housing, Door fuel filler, Outside door handle etc.) Note
6、: The requirement of WL-line refers to Figure 1. 1.2.3 Type A3. It is applicable to surface finishes on integral skinned polyurethane foam parts used on the external body. 1.2.4 Type B1. It is applicable to surface finishes used on internal body parts and components within the engine compartment. 1.
7、2.5 Type B2. It is applicable to surface finishes used on internal body parts and components in areas of normal service operation. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 1 P7 :0 : ., E:48 6&F !7$ :4-8! 9I8x $4=F 3L 6$ . :0 : F67t 7568 18 88x
8、7 , F6* 72T8p) F$ . 1.1 +95 . ., E:48t 8% =8 ! 787 F(3D% .E8 8Td $8+7 $4F 8-L95 ,p2e 4G 7 $4F7 9IF 8$ . 1.2 957 -88 . $88 54: Type7 8F .%P$ . 1.2.1 Type A1. 8% = 7. = -C 7. .E :E -4 F 97 “%P $8+ . (WL-Line F$ : Fascia Bumper, Radiator Grille, MOLDG R/PNL, CVR Towing Eye &% ). 1.2.2 Type A2. 8% = 7.
9、= -C 7. .E :E .(B8 97 “%P $8+ . (WL-Line 1. : Handle Trunk Lid, OSRVM Housing, Door Fuel Filler, Outside Door Handle &% ). :0 : WL-LINE8 9I8t ,* . 18x =lF . 1.2.3 Type A3. 8% = 7. .E :E 7)%P $8+ . 2 4) E:4 / :0 : C-H +d%P 9I8 6# F 48 07 38%P E:48x 957F$ . GM KOREA ENGINEERING STANDARDS EDS-T-7010 Co
10、pyright 2012 General Motors Company All Rights Reserved March 2012 Page 2 of 7 Version : 8 2.1 External Standards/Specifications. None 2.2 GM Standards/Specifications. EDS-T-7005 EDS-T-7417 EDS-T-7422 EDS-T-7513 EDS-T-7617 EDS-T-7618 EDS-T-7701 EDS-T-7735 EDS-T-7738 EDS-T-7746 EDS-T-7756 EDS-T-7758
11、EDS-T-7759 EDS-T-7780 GMW3059 2.3 Additional References. None 3 Test Preparation and Evaluation 3.1 Resources. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternative test facilities and equipment m
12、ay also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.1.3 Equipment. Equipment as required by the appropriate test method. 3.1.4 Test Piece. Unless otherwise specified in the appropriate material sta
13、ndard or drawing, number of test pieces shall be as specified in the relevant test method for the property concerned. 3.2 Conditions. 3.2.1 Conditioning. Unless otherwise specified, tests shall be performed on test pieces in the as received condition, without any special preconditioning. Where, for
14、testing to Type A3, sections rather than complete components are used, all cut edges shall be protected against penetration of moisture by suitable means (e. g. with wax, adhesive tapes etc.). 3.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- GMKOREAEDST70102012TESTMETHODFORORGANICCOATINGSONPLASTICPARTSPDF

链接地址:http://www.mydoc123.com/p-757190.html