1、A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2089 1 of 3 February, 1993 March, 2005 NAME: ADHESIVE - STRUCTURAL - TWO COMPONENT - PART A THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPI
2、ENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificationMatspec.doc 1. SCOPE The material described in this specification is the Part A component of a two-part pumpable structural adhesive system. The adhesive system is used
3、for bonding the hems of oily and unclean metal substrates, such as galvanized steel, zinc coated steel and CRLC as used for inner and outer panels of engine hoods, deck lids and doors. 2. PROPERTIES 2.1 Viscosity Test Method HN 0060 Meter 1 Procedure A 550 kPa air pressure 2.1.1 As Received 4 - 6 se
4、conds. 2.1.2 Aged Viscosity 7 days 40 2C 12 seconds Max. 2.1.3 After Storage 3 months 27 2C 15 seconds Max. 2.2 Solids (ASTM D2835) 100% Sample dried at 102 3C for 3 hours A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 2089 2 of 3 F
5、ebruary, 1993 March, 2005 NAME: ADHESIVE - STRUCTURAL - TWO COMPONENT - PART A THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms MaterialSpecificat
6、ionMatspec.doc 2. PROPERTIES (continued) 2.3 Uncured Shear Adhesion 400 N min. Prepare 6 assemblies as shown in Fig. 1, placing Part A component in the area to be hemmed and close the hem in the hemming press. Pull the inner panel out of the hem at 12min/min and record load. 2.4 Storage The material
7、 should be stored out of sunlight at a temperature no higher than 35 C. 2.5 Shelf Life Under the conditions of Clause 2.4 the shelf life should be 6 months minimum. 2.6 Colour White. A.C.N. 006 893 232 Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 20
8、89 3 of 3 February, 1993 March, 2005 NAME: ADHESIVE - STRUCTURAL - TWO COMPONENT - PART A THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : I:CentralLaboratoryStandardForms Materia
9、lSpecificationMatspec.doc 3. APPROVAL, INSPECTION AND REJECTION Refer HN 1000, Clauses A, C and G(Line Trial). 4. HAZARDOUS MATERIALS Refer HN 1000, Clause H. 5. RESTRICTED AND REPORTABLE SUBSTANCES Refer HN 1000, Clause J. 7. APPROVED SUPPLIERS AND MATERIALS Material known to meet the full requirem
10、ents of this specification: MATERIAL SUPPLIER LORD CHEMICAL PRODUCTS AUST. PTY LTD VERSILOK 253 LORD CORPORATION, USA 8. REFERENCES HN 0060 ASTM D2835 HN 1000 9. REVISIONS March 2005 - Removal of reference to HN 1000 Clause B in section 3.APPROVAL, INSPECTION AND REJECTION. - Transfer of the information on HN 2089 APPROVED SOURCE SHEET into section 7.APPROVED SUPPLIERS AND MATERIALS. - Revised supplier name in section 7.APPROVED SUPPLIERS AND MATERIALS. - Added sections 4.HAZARDOUS MATERIALS, 5.RESTRICTED AND REPORTABLE SUBSTANCES and 8.REFERENCES. Prepared by: Y. Zia
