1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 2 NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECI
2、FICATION) NUMBER: CEMS BT-34 TITLE: Oil Content Test Adapted from ORD JR-OME PD #115 dated 21 November 1956. CURRENT ISSUE DATE: August 2009 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: October 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIE
3、D FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the appli
4、cability of regulatory limits prior to use. Change Notice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive. 1.0 SCOPE This method covers a procedure for determining the oil content of a material such as engine cooling system stopleak compound. 2.0
5、APPARATUS 2.1 Mortar and pestle 2.2 Steam bath 2.3 Analytical balance with a sensitivity of 0.1 milligram 2.4 Erlenmeyer flask, 500 milliliters 2.5 Beaker, 250 milliliters 2.6 Filter funnel 2.7 Desiccator 2.8 Gravity-convection oven capable of maintaining 212 + 2 degrees Fahrenheit 2.9 Graduated cyl
6、inder, 50 milliliters 3.0 MATERIAL 3.1 Filter paper, coarse 3.2 Ethyl ether, ACS 3.3 Trichloroethylene, ACS 4.0 PROCEDURE 4.1 Place approximately 10 grams of samples, weighed to the nearest 0.01 gram, into a 500 milliliter Erlenmeyer flask. 4.2 Add 40 milliliters of trichloroethylene and place the f
7、lask on the steam bath for 30 minutes. 4.3 Remove from the steam bath and cool to room temperature. 4.4 Filter the contents through a coarse filter paper collecting the filtrate in the 250 milliliter beaker which has been previously weighed to the nearest 0.1 milligram. 4.5 Wash the flash three time
8、s with 10 milliliter portions of trichloroethylene, passing the washings through the filter into the tared beaker. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS BT-
9、34 TITLE Oil Content Test CURRENT ISSUE DATE: August 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 2 of 2
10、4.6 Wash the oil from the filter paper using trichloroethylene, collecting the washing in the tared beaker. 4.7 Place the beaker on a steam bath and evaporate the trichloroethylene. 4.8 Cool the beaker and add 10 milliliters of ethyl either. Mix and evaporate the either on the steam bath. 4.9 Place
11、the beaker into a gravity-convection oven maintained at a temperature of 212 + 2 F for a of 30 minutes. 4.10 At the end of the 30-minute heating period remove the beaker and cool to room temperature in a desiccator. 4.11 Weigh the beaker and contents to the nearest 0.1 milligram. CAUTION: Perform th
12、e evaporations in a hood as vapors of trichloroethylene are toxic and ethyl ether vapors are highly flammable. Do not use open flames. 5.0 REPORT Calculate the oil content as follows: % Oil = (B-A) 100 S where A = weight of the empty beaker in grams B = weight of the beaker and oil in grams C = weight of sample used in grams 5.1 Report the average of duplicate determinations as “Oil content, % by weight”. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
