1、NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECIFICATION)NUMBER: CEMS G-5, Part V GeneralTITLE: Part V Paints Primers, General RequirementsCURRENT ISSUE DATE: October 2008 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: April 2006 PRINTED C
2、OPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and healt
3、h practices and to determine the applicability of regulatory limits prior to use. Change Notice: Added Grade -57 “Autophoretic Coatings”; editorial changes. 1.0 SCOPEThe intent of this specification is to establish acceptable durability and quality levels for the finish on Navistars products and to
4、define requirements and physical properties of the various materials used in the painting operation. 2.0 INTRODUCTION This specification is divided into eight parts as follows: Part I, Section A - Product Finishing Requirements Part V - Primers Part I, Section B - Paint Material Requirements Part VI
5、 - Paints for Repair Phone: 1-800-854-7179. 8.1.1 Color ChipsRequests for color chips should be addressed to: Navistar Non-Metals Laboratory, Truck Development and Technology Center, P.O. Box 1109, Ft. Wayne, IN 46801-1109 8.2 ASTM Test MethodsASTM test methods are available from ASTM, 1916 Race Str
6、eet, Philadelphia, PA 19103 OCTOBER 2008 Page 2 of 4 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS G-5, TITLE: Part V Paints Primers, CURRENT ISSUE DATE: Part V Gen
7、eral General RequirementsOctober 2008 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 Navistar, Inc. 8.3 Federal Test MethodsFederal Test Methods ar
8、e available from the Business Service Center, General Services Administration, Washington, DC 20407 9.0 SOURCE APPROVAL AND QUALITY CONTROL 9.1 Supplier RequirementsAll suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 reg
9、istration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Corporate Buyer upon req
10、uest. 9.2 ApprovalParts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples that were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in mat
11、erial, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering at TDTC and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification
12、, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 9.3 Process ControlThe supplier shall either perform and report results of tests on specific lots of parts produced using ISO
13、 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using NAVISTAR plant
14、 may determine testing and reporting requirements on specific products. 10.0 DESIGNATION ON DRAWINGS AND PURCHASE ORDERS 10.1 Engineering DrawingsEngineering generally specifies only the Class of Finish on its drawings. The finish classification describes the durability, corrosion resistance, and ap
15、pearance requirements of the part or assembly. It is the responsibility of the supplier or of Manufacturing to determine the need for primers and/or casting sealers in order to satisfy the specified finish requirements. 10.2 Purchase Orders Purchase orders should include the grade of the casting sea
16、ler and reference this specification; if necessary, the color, by the Navistar paint color number, may be included. When necessary, the desired viscosity range should also be included on the purchase order. Example: 0001-52 FRP Primer, per CEMS G-5, Pt. V Viscosity 40-50 seconds OCTOBER 2008 Page 3
17、of 4 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS G-5, TITLE: Part V Paints Primers, CURRENT ISSUE DATE: Part V General General RequirementsOctober 2008 This docum
18、ent is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 Navistar, Inc. 11.0 PACKING AND SHIPPING Packing, shipping and identification shall be in accordance with Manu
19、facturing Standard MS-D-13. 12.0 CONTACT INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Cent
20、er (TDTC) 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/OCTOBER 2008 Page 4 of 4 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
