1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. OCTOBER 2009 Page 1 of 11 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER
2、 TMS-6040 TITLE: Thermoplastic Elastomer Molding Compounds CURRENT REV. No: 0910 DATE: October 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. 0904 April 2009 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification m
3、ay involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use.
4、 Change Notice: Added material to Table 3b. Reference: File 30-16 Keywords: thermoplastic rubber 1.0 APPLICATION This specification covers thermoplastic rubber compounds used for various truck applications that may or may not contain recycled rubber materials. For thermoset compounds, see TMS-6039.
5、1.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 2.0 SCOPE This specification covers general requirements, identification, inspection, property and performanc
6、e requirements, quality plan, and source approval and quality control requirements. 2.1 Descriptions This specification covers several categories of material types with several choices within each category. The choices within each category typically vary by hardness and related physical properties b
7、ut can apply to similar applications. The following base material designations are available: 2.1.1 TPR This designates a standard thermoplastic rubber material. It usually consists of thermoplastic olefins (TPO) blended with elastomers, although other polymer bases are available. These materials ma
8、y contain recycled rubber (post consumer automotive tire) with prior approval. Typical applications include grommets, bumpers, boots, aero effect seals, body seals, sound dampers, closeouts, air ducts, trim components, valence panels and other interior and exterior applications. 2.1.2 TPU This desig
9、nates a thermoplastic urethane material suitable for many of the applications listed above and has its own unique properties. 2.2 Descriptions Suffix The following suffix modifications are available: 2.2.1 H This designates a heat and weather resistant thermoplastic material. Minimal oil resistance
10、is expected for this material. 2.2.2 O This suffix designates a material with good oil and diesel fuel resistance. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6040
11、 TITLE: Thermoplastic Elastomer Molding Compounds REVISION: 0910 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. OCTOBER 2009 Page
12、 2 of 11 2.2.3 C This suffix designates a heat and weather resistant material with resistance to heavy duty diesel coolants. Minimal oil resistance is expected for this material. Typical applications include water seals, air seals, and hoses. 2.2.4 Compound Variations. A lower case letter may be use
13、d at the end of the compound designation, after the tensile strength number to indicate a specific compound. The absence of this designation also indicates a specific compound a designated by this specification. 2.3 Designation on Drawings The drawing designation shall consist of the base type of ma
14、terial TPR followed by any suffix requirements H, O, or C which is then followed by the durometer specified with an “A” or “D” to designate scale. This is followed by a compound identifier to differentiate compound variations. If desired, the specific base polymer may be identified in the specificat
15、ion as well. For example: 2.3.1 TPR60A-a per TMS-6040 2.3.1.1 This designation identifies a basic elastomer with a durometer of 60 scale A. 2.3.2 TPO per TMS-6040 TPR-H70D-a 2.3.2.1 This designation identifies a TPO compound meeting the heat resistance requirements with a durometer of 70, scale D. T
16、his is also a specific compound variation a designated by the “a.” 2.3.3 Polyester per TMS-6040 TPR-O55D-b 2.3.3.1 This is an oil resistant polyester elastomer compound with a durometer of 55, scale D. This compound is designated “b.” 2.3.4 TPR-0020 per TMS-6040 2.3.4.1 An alternate designation, int
17、ended primarily for parts still under development that may require material property modifications prior to final production release but after the print geometry has been determined. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The foll
18、owing specifications and standards are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 ASTM D 412 ASTM D 395 NAVISTAR Eng. Design Std. A-16 ASTM D 624 ASTM D 865 NAVISTAR Manufacturing Standard MS-D-13 ASTM D 573 ASTM D 5992 CFR Title 29, Part 1910 ASTM D 1171 ASTM B 1
19、17 NAVISTAR CEMS B-50 ASTM D 2137 ASTM D 575 NAVISTAR CEMS GT-31 ASTM D 2240 TMS-9543 4.0 GENERAL REQUIREMENTS All materials covered by this specification shall meet the following requirements and shall be molded or extruded utilizing good industry practice. 4.1 Finish Unless otherwise specified on
20、the engineering drawing the part finish for molded parts shall be uniform as produced from a polished steel tool. The mold will be polished to a surface finish of 800 nm or better with small, incidental to part function or appearance, tool marks not polished out. Extruded products shall have a smoot
21、h and clean surface finish free from any foreign matter. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6040 TITLE: Thermoplastic Elastomer Molding Compounds REVISION
22、 0910 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. OCTOBER 2009 Page 3 of 11 4.2 Flash Unless otherwise specified on the engin
23、eering drawing the part shall have a maximum flash allowance of 0.80 mm. 4.3 Dimensional Tolerances Part tolerances are shown in Tables 1 and 2. These tolerances shall override standard print tolerances unless otherwise stated on the print or unless specific tolerances are designated on the part det
24、ail. TABLE 1 STANDARD DIMENSIONAL TOLERANCE TABLE Dimension (in) Tolerance Dimension (mm) Tolerance 0 - 1.00 .015 0 - 25 .40 1.00 - 4.00 .020 25 - 100 .50 4.00 - 6.30 .032 100 - 160 .80 6.30 this report is authorization of that approval prior to this change. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6
25、1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements.
26、 Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their NAVISTAR Corporate Buyer upon request. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networ
27、king permitted without license from IHS-,-,-NUMBER: TMS-6040 TITLE: Thermoplastic Elastomer Molding Compounds REVISION: 0910 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume al
28、l patent liability. 2009 by Navistar, Inc. OCTOBER 2009 Page 5 of 11 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples that were approved by the purchaser. No changes in formulation or processing practices
29、are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, NAVISTAR Truck Development and Technology Center and Purchasing and Supplier Develop
30、ment of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples (when the results are ambiguous and not easily describe or photographed with sufficient resolution), and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accorda
31、nce with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state
32、of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIF
33、ICATION Loading, packing and identification shall be in accordance with NAVISTAR Manufacturing Standard MS-D-13. 7.1 Identification When practical, parts shall be labeled or engraved in clearly legible block capital letters not less than 3 mm high with the following information: (a) Vendor code A fo
34、ur- or five-digit code assigned by NAVISTAR to each vendor. Contact Corporate Technical Standards, Truck Development and Technology Center, for assignment of codes. (b) Material Type For example: TMS 6040, TPR60D-a. (c) Part Number Each part shall be identified with the NAVISTAR part number. (d) Dat
35、e or Batch Code A code identifying the date of manufacture, the specific batch of parts, and the mold cavity number, if applicable, shall be included in the identification of each part. The specific code to be used by each supplier shall be agreed upon and approval for the use of the code shall be o
36、btained in writing prior to the delivery of parts for use in production. 8.0 APPROVED SOURCES See Table 3 and above information for approved compounds and sources. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permit
37、ted without license from IHS-,-,-NUMBER: TMS-6040 TITLE: Thermoplastic Elastomer Molding Compounds REVISION: 0910 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent li
38、ability. 2009 by Navistar, Inc. OCTOBER 2009 Page 6 of 11 9.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck
39、Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ TABLE 2 DURATION/TEMPERATURE TABLE Test Designation Duration hours Temper
40、ature C) A 70 70 B 168 100 C 168 125 D 168 150 E 168 175 F 250 200 G 250 225 H 250 250 J 250 275 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6040 TITLE: Thermoplas
41、tic Elastomer Molding Compounds REVISION: 0910 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. OCTOBER 2009 Page 7 of 11 TABLE 3a
42、TPR MATERIAL REQUIREMENTS Designation TPR49A TPR60A TPR62A TPR88A-a TPR46A Material ID TPR-0003 TPR-0004 TPR-0007 TPR-0001 TPR-0005 Polymer Property Hardness 52 R1 62 88 A 40 Tensile Strength 3.0 R1 5.2 4 5 Tensile at 100% Elongation 1.4 R1 1.9 R1 R1 Elongation 550 R1 320 100 700 Tear Resistance 17
43、R1 17 30 R1 Compression Set 50% R1 50% 80 50% Low Temperature Pass Pass Pass Pass Pass Heat Resistance B A D A A Hardness +- 5 R1 71 max +- 5 +- 5 Tensile Strength +- 15 R1 4.5 min +- 15 +- 15 Elongation +- 25 R1 300% min +- 25 +- 25 Oil Resistance A A A A A Hardness NA R1 R1 NA NA Swell NA R1 95% m
44、ax NA NA Weather Resistance Exterior Exterior Exterior Exterior Exterior Recycled Content 45 Approved Supplier Dow Corning Dow Corning Delphi NRI Industries PolyOne Compound Designation TES A 5110 EV1 TPR A 6221 CUV DX300003 Symar-T 200 Bergaflex BFI G40A-350 Approved Supplier Santoprene Compound De
45、signation TPV 121-62M100 1 “R” - report values; specification limits have not been determined yet. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6040 TITLE: Thermopl
46、astic Elastomer Molding Compounds REVISION: 0910 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. OCTOBER 2009 Page 8 of 11 TABLE 3
47、b TPR MATERIAL REQUIREMENTS Designation TPR-60D-a TPR-90A-a Material ID TPR-0008 TPR-0012 Polymer TPO TPO Property Hardness 60D 90 Tensile Strength 12 5.5 Tensile at 100% Elongation 5.0 Elongation 550 150 Tear Resistance 40 (Die C) Compression Set 80 Low Temperature Pass Pass Heat Resistance A A Hardness 5 3 Tensile Strength 25 15 Elongation 40 25 Oil Resistance Hardness Swell Weather Resistance Exterior Exterior Recycled Content 50% Approved Supplier Compound Designation Ap
