IS 13892-1994 Correspondence envelopes - specification.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD ESA-M2D110-C-2009 RUBBER BOOT - SEVERE COLD SERVICE TO BE USED WITH FORD WSS-M99P1111-A 《严寒环境作业用胶靴 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESA-M2D122-A-2011 HOSE LOW PRESSURE - POWER STEERING TO BE USED WITH FORD WSS-M99P1111-A 《软管 低压动力方向盘 与福特WSS-M99P1111-A 一起使用[使用 福特WSS-M2D513-A]》.pdf

FORD ESA-M2D17-B-2009 HOSE HIGH EXPANSION - POWER STEERING PRESSURE TO BE USED WITH FORD WSS-M99P1111-A 《动力转向装置用高伸展性压力软管 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESA-M2D183-B-2004 NEOPRENE VACUUM FITTING - MOLDED TO BE USED WITH FORD WSS-M99P1111-A 《模制真空装置用氯丁橡胶 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESA-M2D197-A1-2009 THERMOPLASTIC POLYURETHANE ELASTOMER 80 DUROMETER A HARDNESS TO BE USED WITH FORD WSS-M99P1111-A 《硬度为80 A的热塑性聚氨酯弹性体 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESA-M2D198-A-2009 THERMOPLASTIC POLYURETHANE ELASTOMER 55 DUROMETER D HARDNESS TO BE USED WITH FORD WSS-M99P1111-A 《硬度为55 D的热塑性聚氨酯弹性体 与标准FORD WSS-M99P1111-A一起使用 列于标准FORD E.pdf

FORD ESA-M2D213-A-2009 POLYURETHANE MOLDING COMPOUND ETHER BASED TO BE USED WITH FORD WSS-M99P1111-A 《聚氨酯成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESA-M2D223-A-2009 RUBBER ENGINE MOUNTS - INSULATOR TO BE USED WITH FORD WSS-M99P1111-A 《发动机架用绝缘体橡胶 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESA-M2D230-A7-2009 ELASTOMER POLYESTER - BLOW MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《弹性体聚酯吹塑塑料 与标准FORD WSS-M99P1111-A一起使用 》.pdf