1、 AMERICAN NATIONAL STANDARD ANSI/ISA75.08.012016 Formerly ISA-75.03-1992 Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (Classes 125, 150, 250, 300, and 600) Approved 28 July 2016 ANSI/ISA-75.08.01-2016 Face-to-Face Dimensions for Integral Flanged Globe-Style Control V
2、alve Bodies (Classes 125, 150, 250, 300, and 600) ISBN: 978-1-945541-02-5 Copyright 2016 by the International Society of Automation (ISA). All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or tra
3、nsmitted in any form or by any means (electronic mechanical, photocopying, recording, or otherwise), without the prior written permission of the Publisher. ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709 3 ANSI/ISA-75.08.01-2016 Preface This preface, as well as all
4、 footnotes and annexes, is included for information purposes and is not part of ANSI/ISA-75.08.01-2016. The standards referenced within this document may contain provisions which, through reference in this text, constitute requirements of this document. At the time of publication, the editions indic
5、ated were valid. All standards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers of currently valid In
6、ternational Standards. ANSI maintain registers of currently valid U.S. National Standards. This document has been prepared as part of the service of ISA toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should be subject to perio
7、dic review. Toward this end, the Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288; E-mail: standardsis
8、a.org. The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the benefits to USA use
9、rs of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards, recommended practices,
10、 and technical reports to the greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric System, published by the American Society for Testing certifies industry professionals; provides education and training; publishes books and technical articles; hosts
11、 conferences and exhibits; and provides networking and career development programs for its 40,000 members and 400,000 customers around the world. ISA owns A, a leading online publisher of automation-related content, and is the founding sponsor of The Automation Federation (www.automationfederation.o
12、rg), an association of non-profit organizations serving as “The Voice of Automation.“ Through a wholly owned subsidiary, ISA bridges the gap between standards and their implementation with the ISA Security Compliance Institute (www.isasecure.org) and the ISA Wireless Compliance Institute (www.isa100
13、wci.org). The following people served as members of ISA Subcommittee ISA75.08 and approved ANSI/ISA-75.08.01-2016: NAME COMPANY W. Weidman, Chair Consultant V. Mezzano, Managing Director Fluor Corporation H. Baumann H B Services Partners LLC F. Cain Flowserve Corporation R. Duimstra Fisher Controls
14、International Inc. J. Young The Dow Chemical Company The following people served as members of ISA Committee ISA75 and approved ANSI/ISA-75.08.01-2016: NAME COMPANY J. Young, Chair The Dow Chemical Company V. Mezzano, Co-Managing Director Fluor Corporation W. Weidman, Co-Managing Director Consultant
15、 5 ANSI/ISA-75.08.01-2016 A. Abromaitis S&T Design H. Baumann H B Services Partners LLC J. Beall Emerson Process Management M. Bober SPX Flow Technology H. Boger Consultant S. Boyle Consultant F. Cain Flowserve Corporation R. Duimstra Fisher Controls International Inc. J. Faramarzi Control Component
16、s Inc. C. Hergert Kellogg Brown & Root H. Hoffmann Consultant J. Kiesbauer Samson Aktiengesellschaft A. Libke DeZURIK G. Liu Consultant T. Loudin Larox Flowsys Inc. D. Martin Valve Solutions Ltd. H. Maxwell Haines Fluid Dynamics H. Miller Consultant A. Sahraei Enbridge Pipelines Inc LP E. Skovgaard
17、Consultant This standard was approved by the ISA Standards and Practices Board on 18 July 2016: NAME COMPANY N. Sands, Vice President DuPont D. Bartusiak ExxonMobil Research & Engineering P. Brett Honeywell Inc. E. Cosman OIT Concepts, LLC D. Dunn Phillips 66 J. Federlein Federlein & Assoc. LLC B. F
18、itzpatrick Wood Group Mustang J. Gilsinn Kenexis Consulting J.-P. Hauet KB Intelligence J. Jamison Encana Corp. D. Lee UCDS K.-P. Lindner Endress+Hauser Process Solutions AG T. McAvinew Consultant V. Mezzano Fluor Corp. C. Monchinski Automated Control Concepts Inc. D. Reed Rockwell Automation H. Sas
19、ajima Fieldcomm Group Inc. Asia-Pacific T. Schnaare Rosemount Inc. J. Tatera Tatera & Associates Inc. K. Unger Consultant I. Verhappen Industrial Automation Networks D. Visnich Burns & McDonnell W. Weidman Consultant J. Weiss Applied Control Solutions LLC M. Wilkins Yokogawa D. Zetterberg Chevron En
20、ergy This page intentionally left blank. 7 ANSI/ISA-75.08.01-2016 Contents 1 Scope . 9 2 Purpose 9 3 Definitions 9 4 Dimensional data . 9 5 References . 11 This page intentionally left blank. 9 ANSI/ISA-75.08.01-2016 1 Scope This standard applies to integral flanged globe-style control valves, sizes
21、 15 mm (1/2 inch) through 400 mm (16 inches), having top, top and bottom, port, or cage guiding. Pressure Classes 125 flat face, and 150, 250, 300, and 600 raised face, flanged control valves are included. 2 Purpose The purpose of this standard is to aid users in their piping design by providing fla
22、nge, face-to-face control valve dimensions, without giving special consideration of the equipment manufacturer to be used. 3 Definitions For definitions of terms used in this standard, see ISA-75.05.01, Control Valve Terminology. 4 Dimensional data 4.1 Face-to-face dimensions for integral flanged gl
23、obe-style control valves. See Table 1. 4.2 For end-to-end dimensions of flanged with ring joint ends, Dimension “A“ shall be adjusted accordingly to ASME B16.10, paragraph 3.3. ANSI/ISA-75.08.01-2016 - 10 - Table 1 Face-to-face dimensions for integral flanged globe-style control valves Nominal valve
24、 Size Classes 125 and 150 Classes 250 and 300 Class 600 Tolerance (All Classes) Dimension “A” Dimension “A” Dimension “A” mm Inches mm Inches mm inches mm inches mm inches 15 184 7.25 190 7.50 203 8.00 1.6 0.062 20 184 7.25 194 7.62 206 8.12 1.6 0.062 25 1 184 7.25 197 7.75 210 8.25 1.6 0.062 40 1-1
25、/2 222 8.75 235 9.25 251 9.88 1.6 0.062 50 2 254 10.00 267 10.50 286 11.25 1.6 0.062 65 2-1/2 276 10.88 292 11.50 311 12.25 1.6 0.062 80 3 298 11.75 318 12.50 337 13.25 1.6 0.062 100 4 352 13.88 368 14.50 394 15.50 1.6 0.062 150 6 451 17.75 473 18.62 508 20.00 1.6 0.062 200 8 543 21.38 568 22.38 610
26、 24.00 1.6 0.062 250 10 673 26.50 708 27.88 752 29.62 1.6 0.062 300 12 737 29.00 775 30.50 819 32.25 3.2 0.125 350 14 889 35.00 927 36.50 972 38.25 3.2 0.125 400 16 1016 40.00 1057 41.62 1108 43.62 3.2 0.125 Flat face Raised face 11 ANSI/ISA-75.08.01-2016 5 References The following bibliography is i
27、ncluded for the definition of pressure classes and flange dimensions, material identification, and cross-reference information. AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) ASME B16.1-1998 Cast Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, and 250 ASME B16.5-2003 Pipe Flanges and Flang
28、ed Fittings: NPS 1/2 through 24 ASME B16.10-2000 (R2003) Face-to-Face and End-to-End Dimensions of Valves ASME B16.24-2001 Cast Copper Alloy Pipe Flanges and Flanged Fittings: Class 150, 300, 400, 600, 900, 1500, and 2500 ASME B16.34-2004 Valves Flanged, Threaded and Welding End ASME B16.42-1998 Duc
29、tile Iron Pipe Flanges and Flanged Fittings: Classes 150 and 300 Available from: ASME Three Park Avenue New York, NY 10016-5990 Tel: 800-843-2763 http:/www.asme.org INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) IEC 60534-3-1 (2000) Industrial-Process Control Valves - Part 3-1: Dimensions - Face-to
30、-Face Dimensions for Flanged, Two-Way, Globe-Type, Straight Pattern and Centre-to-Face Dimensions for Flanged, Two-Way, Globe-Type, Angle Pattern Control Valves Available from: IEC 3, rue de Varemb P.O. Box 131 CH - 1211 Geneva 20 Switzerland http:/www.iec.ch This page intentionally left blank. 13 A
31、NSI/ISA-75.08.01-2016 Annex A Dimensions for metrically sized valves This annex is not part of ANSI/ISA-75.08.01-2016, but it is included to facilitate its use. The ASME standards listed in the bibliography contain valve body design information in addition to face-to-face dimensions. Dimensions for
32、metrically sized valves are nominal conversions that are conventionally used in documents by the Manufacturers Standardization Society (MSS) of the Valve and Fitting Industry (MSS-SP-86-2002) and by the International Electrotechnical Commission (IEC). Control valve initial dimensions, 10 inches - 16
33、 inches, were listed in the Fluid Control Institute (FCI) Standard, FCI-65-2-1975, which has been withdrawn from publication. This page intentionally left blank. Developing and promulgating sound consensus standards, recommended practices, and technical reports is one of ISAs primary goals. To achie
34、ve this goal the Standards and Practices Department relies on the technical expertise and efforts of volunteer committee members, chairmen and reviewers. ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) a
35、nd provides secretariat support for International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Societys standards program, please write: ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709 ISBN: 978-1-945541-02-5
