JASO M902-2007 Road vehicles-Interior parts and materials-Measurement methods of diffused volatile organic compounds(VOC)《道路车辆 内部件和材料 挥发性有机化合物(VOC)扩散的测量方法》.pdf

相关资源

JASO Z124-2008 Heavy commercial vehicles and buses - Braking in a turn - Open-loop test methods《重型商用机动车和大客车 转向时制动 开环测试方法》.pdf

JASO Z123-2007 Automotive parts-Air conditioner-Test method for measuring refrigerant (R134a)leakage《汽车部件 空调 制冷剂(R134a)泄漏用试验方法》.pdf

JASO Z117-1-2007 Road vehicles-Vehicle dynamics test methods-Part 1 General conditions for passenger cars《道路车辆 车辆动态试验方法 第1部分 客车用通用条件》.pdf

JASO Z003-2007 Forms for automobile performance diagram《汽车性能图用样式》.pdf

JASO T202-1977 Test Code of Brake Lever Strength and Requirements for Motor Cycles.pdf

JASO T013-2007 Motorcycles-lane change test procedure《摩托车 行车道改变试验程序》.pdf

JASO T011-2007 Motorcycles-Steady state circular test procedure《摩托车 稳定状态循环试验程序》.pdf

JASO T006-2007 Motorcycles-Procedure for H-point Determination《摩托车 H点测定用程序》.pdf

JASO M355-2008 Automotive diesel engine oils《汽车供应柴油机油》.pdf

猜你喜欢

BS 3SP 3-1943 Specification for aircraft material - Fork joints (low tensile type) (for sizes No 4 B A to 1 2 inch B S F inclusive)《航空器材料规格 叉形接头(低强度型)(尺寸从No 4 B A 至含1 2 in B S F )》.pdf

BS 3SP 89-1983 Specification for characteristics boundary dimensions tolerances and static load ratings of airframe bearings《飞机机体轴承特性、界面尺寸、容差及静载荷等级规范》.pdf

BS 3T 53-1980 Specification for chromium-molybdenum steel tube (700 MPa) (outside diameter not less than 12 5 mm) (weldable)《铬-钼钢管材规范(700MPa)(管外径不小于12 5mm)(可焊接)》.pdf

BS 3T 60-1980 Specification for chromium-molybdenum steel tube (1150 MPa) (maximum thickness 8 mm)《铬-钼钢管材规范(1150MPa)(最大厚度8mm）》.pdf

BS 3TA 1-2009 Specification for sheet and strip of commercially pure titanium (tensile strength 290-420 MPa)《工业纯钛薄板材和带材规范(抗拉强度290-420 MPa)》.pdf

BS 3TA 10-2009 Specification for sheet of titanium-aluminium-vanadium alloy (tensile strength 960-1270 MPa)《钛-铝-钒合金薄板材规范(抗拉强度960-1270 MPa)》.pdf

BS 3TA 100-2009 Procedure for inspection testing and acceptance of wrought titanium and titanium alloys《锻造钛和钛合金的检验、测试和验收规范》.pdf

BS 3TA 11-2009 Specification for bar and section for machining of titanium-aluminium -vanadium alloy (tensile strength 900-1160 MPa) (limiting ruling section 150 mm)《钛铝钒合金棒材和型材的加工规.pdf

BS 3TA 2-2009 Specification for sheet and strip of commercially pure titanium (tensile strength 390-540 MPa)《工业纯钛板材和带材规范(抗拉强度390-540 MPa)》.pdf