1、JEDEC STANDARD Stress-Test-Driven Qualification of Integrated Circuits JESD47J (Revision of JESD47I.01, October 2016) AUGUST 2017 JEDEC SOLID STATE TECHNOLOGY ASSOCIATION NOTICE JEDEC standards and publications contain material that has been prepared, reviewed, and approved through the JEDEC Board o
2、f Directors level and subsequently reviewed and approved by the JEDEC legal counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and
3、 assisting the purchaser in selecting and obtaining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or internationally. JEDEC standards and publications are adopted without regard to whether or not their adoption
4、 may involve patents or articles, materials, or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the JEDEC standards or publications. The information included in JEDEC standards and publications represen
5、ts a sound approach to product specification and application, principally from the solid state device manufacturer viewpoint. Within the JEDEC organization there are procedures whereby a JEDEC standard or publication may be further processed and ultimately become an ANSI standard. No claims to be in
6、 conformance with this standard may be made unless all requirements stated in the standard are met. Inquiries, comments, and suggestions relative to the content of this JEDEC standard or publication should be addressed to JEDEC at the address below, or refer to www.jedec.org under Standards and Docu
7、ments for alternative contact information. Published by JEDEC Solid State Technology Association 2017 3103 North 10th Street Suite 240 South Arlington, VA 22201-2107 This document may be downloaded free of charge; however JEDEC retains the copyright on this material. By downloading this file the ind
8、ividual agrees not to charge for or resell the resulting material. PRICE: Contact JEDEC Printed in the U.S.A. All rights reserved PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by JEDEC and may not be reproduced without permission. For information, contact: JEDEC Solid State Technology A
9、ssociation 3103 North 10th Street Suite 240 South Arlington, VA 22201-2107 or refer to www.jedec.org under Standards-Documents/Copyright Information. JEDEC Standard No. 47J Page 1 STRESS DRIVEN QUALIFICATION OF INTEGRATED CIRCUITS (From JEDEC Board Ballot, JCB-17-09, formulated under the cognizance
10、of the JC14.3 Subcommittee on Silicon Devices Reliability Qualification and Monitoring.) 1 Scope This standard describes a baseline set of acceptance tests for use in qualifying electronic components as new products, a product family, or as products in a process which is being changed. These tests a
11、re capable of stimulating and precipitating semiconductor device and packaging failures. The objective is to precipitate failures in an accelerated manner compared to use conditions. Failure Rate projections usually require larger sample sizes than are called out in qualification testing. For guidan
12、ce on projecting failure rates, refer to JESD85 Methods for Calculating Failure Rates in Units of FITs. This qualification standard is aimed at a generic qualification for a range of use conditions, but is not applicable at extreme use conditions such as military applications, automotive under-the-h
13、ood applications, or uncontrolled avionics environments, nor does it address 2ndlevel reliability considerations, which are addressed in JEP150. Where specific use conditions are established, qualification testing tailored to meet those specific requirements can be developed, using JESD94 that will
14、result in a better optimization of resources. This set of tests should not be used indiscriminately. Each qualification project should be examined for: a) Any potential new and unique failure mechanisms. b) Any situations where these tests/conditions may induce invalid or overstress failures. If it
15、is known or suspected that failures either are due to new mechanisms or are uniquely induced by the severity of the test conditions, then the application of the test condition as stated is not recommended. Alternatively, new mechanisms or uniquely problematic stress levels should be addressed by bui
16、lding an understanding of the mechanism and its behavior with respect to accelerated stress conditions (Ref. JESD91, “Method for Developing Acceleration Models for Electronic Component Failure Mechanisms” and JESD94, “Application Specific Qualification using Knowledge Based Test Methodology”). Consi
17、deration of PC board assembly-level effects may also be necessary. For guidance on this, refer to JEP150, Stress-Test-Driven Qualification of and Failure Mechanisms Associated with Assembled Solid State Surface-Mount Components. This document does not relieve the supplier of the responsibility to as
18、sure that a product meets the complete set of its requirements. JEDEC Standard No. 47J Page 2 2 Reference documents The revision of the referenced documents shall be that which is in effect on the date of the qualification plan. 2.1 Military MIL-STD-883, Test Methods and Procedures for Microelectron
19、ics MIL-PRF 38535 2.2 Industrial UL94, Tests for Flammability of Plastic Materials for Parts in Devices and Appliances. ASTM D2863, Flammability of Plastic Using the Oxygen Index Method. IEC Publication 695, Fire Hazard Testing. J-STD-020, Joint IPC/JEDEC Standard, Moisture/Reflow Sensitivity Classi
20、fication for Nonhermetic Solid State Surface-Mount Devices. JP-001, Foundry Process Qualification Guidelines (Wafer Fabrication Manufacturing Sites). JS-001, Joint JEDEC/ESDA Standard for Electrical Discharge Sensitivity Test - Human Body Model (HBM) Component Level JS-002, ESDA/JEDEC Joint Standard
21、 for Electrostatic Discharge Sensitivity Testing Charged Device Model (CDM) Device Level J-STD-002, Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires JESD22 Series, Reliability Test Methods for Packaged Devices JESD46, Guidelines for User Notification of Product/proces
22、s Changes by Semiconductor Suppliers. JESD69, Information Requirements for the Qualification of Silicon Devices. JESD74, Early Life Failure Rate Calculation Procedure for Electronic Components. JESD78, IC Latch-Up Test. JESD85, Methods for Calculating Failure Rates in Units of FITs. JESD86, Electric
23、al Parameters Assessment. JESD94, Application Specific Qualification using Knowledge Based Test Methodology. JESD91, Methods for Developing Acceleration Models for Electronic Component Failure Mechanisms. JEP122, Failure Mechanisms and Models for Semiconductor Devices. JEP143, Solid State Reliabilit
24、y Assessment Qualification Methodologies. JEP150, Stress-Test-Driven Qualification of and Failure Mechanisms Associated with Assembled Solid State Surface-Mount Components. JESD201, Environmental Acceptance Requirements for Tin Whisker Susceptibility of Tin and Tin Alloy Surface Finishes JEDEC Stand
25、ard No. 47J Page 3 3 General requirements 3.1 Objective The objective of this procedure is to ensure that the device to be qualified meets a generally accepted set of stress test driven qualification requirements. Qualification is aimed at components used in commercial or industrial operating enviro
26、nments. 3.2 Qualification family While this specification may be used to qualify an individual component, it is designed to also qualify a family of similar components utilizing the same fabrication process, design rules, and similar circuits. The family qualification may also be applied to a packag
27、e family where the construction is the same and only the size and number of leads differs. Interactive effects of the silicon and package shall be considered in applying family designations. 3.3 Lot requirements Test samples shall comprise representative samples from the qualification family. Manufa
28、cturing variability and its impact on reliability shall be assessed. Where applicable the test samples will be composed of approximately equal numbers from at least three (3) nonconsecutive lots. Other appropriate means may be used to evaluate manufacturing variability. Sample size and pass/fail req
29、uirements are listed in Tables 1-3. Tables A and B give guidance on translating pass/fail requirements to larger sample sizes. Generic data and larger sample sizes may be employed based upon a Chi Squared distribution using a total percent defective at a 90% confidence limit for the total required l
30、ot and sample size. ELFR requirements shall be assessed at a 60% confidence level as shown in Table B. If a single unique and expensive component is to be qualified, a reduced sample size qualification may be performed using 1/3 the sample size listed in the qualification tables. 3.4 Production requ
31、irements All test samples shall be fabricated and assembled in the same production site and with the same production process for which the device and qualification family will be manufactured in production. Samples need to be processed through the full production process including burn-in, handling,
32、 test, and screening. 3.5 Reusability of test samples Devices that have been used for nondestructive qualification tests may be used to populate other qualification tests. Devices that have been used in destructive qualification tests may not be used in subsequent qualification stresses except for e
33、ngineering analysis. Non-destructive qualification tests are: Early Life Failure Rate, Electrical Parameters Assessment, External Visual, System Soft Error, and Physical Dimensions. JEDEC Standard No. 47J Page 4 3.6 Definition of electrical test failure after stressing Post-stress electrical failure
34、s are defined as those devices not meeting the individual device specification or other criteria specific to the environmental stress. If the cause of failure is due to causes unrelated to the test conditions, the failure shall be discounted. 3.7 Required stress tests for qualification Table 1, Tabl
35、e 2, and Table 3 list the qualification requirements for new components. Table 2 and Table 3 are differentiated by package type, but these are not exclusively packaging tests. Interactive effects of the packaging on the silicon also drive the need for tests in Table 2 and Table 3. Power supply volta
36、ge for biased reliability stresses should be Vccmax or Vddmax as defined in the device datasheet as the maximum specified power supply operating voltage, usually the maximum power supply voltage is 5% to 10% higher than the nominal voltage. Some tests such as HTOL may allow for higher voltages to ga
37、in additional acceleration of stress time. JEP122 can provide guidance for accelerating common failure mechanisms. Table 4 lists the required stresses for a qualification family or category of change. Interactive effects from the unchanged aspects of both the silicon and packaging must be assessed.
38、3.8 Pass/Fail criteria Passing all appropriate qualification tests specified in Table 1, Table 2, and Table 3, either by performing the test, showing equivalent data with a larger sample size, or demonstrating acceptable generic data (using an equivalent total percent defective at a 90% confidence l
39、imit for the total required lot and sample size), qualifies the device per this document. When submitting test data from generic products or larger sample sizes to satisfy the Table 1, Table 2, and Table 3 qualification requirements of this document, the number of samples and the total number of def
40、ective devices occurring during those tests must satisfy 90% confidence level of a Poisson exponential binomial distribution, as defined in MIL-PRF 38535. MIL-PRF 38535 is available for free from http:/www.dscc.dla.mil/Programs/MilSpec/listdocs.asp?BasicDoc=MIL-PRF-38535. The minimum number or sampl
41、es for a given defect level can be approximated by the formula: N = 0.5 2(2C+2, 0.1) 1/LTPD 0.5 + C where C = accept #, N=Minimum Sample Size, 2 is the Chi Squared distribution value for a 90% CL, and LTPD is the desired 90% confidence defect level. Table A is based upon this formula, but in some ca
42、ses the sample sizes are slightly smaller than MIL-PRF-38535. JEDEC Standard No. 47J Page 5 3.8 Pass/Fail criteria (contd) Acceptance Number LTPD LTPD LTPD LTPD LTPD LTPD LTPDC 1075321.510 22 32 45 76 114 153 2301 38 55 77 129 194 259 3892 53 76 106 177 266 355 5323 67 96 134 223 334 446 6684 80 115
43、 160 267 400 533 8005 94 133 186 310 465 619 9286 107 152 212 352 528 703 10547 119 170 237 394 590 786 11798 132 188 262 435 652 868 13019 144 205 287 476 713 949 142310 157 223 311 516 773 1030 154311 169 240 335 556 833 1110 166312 181 258 359 596 893 1189 1782Table A Sample Size for a Maximum %
44、Defective at a 90% Confidence LevelEXAMPLE: Using generic data for HTOL with a requirement of 0 rejects from 230 samples. If 700 samples of generic data are available, the maximum number of failures that will meet the qualification test requirement is 3 failures from the LTPD=1 column. 4 Qualificati
45、on and requalification 4.1 Qualification of a new device New or redesigned products (die revisions) manufactured in a currently qualified qualification family may be qualified using one (1) wafer/assembly lot. Electrical parameter assessment is one of the most important tests to run. 4.2 Requalifica
46、tion of a changed device Requalification of a device will be required when the supplier makes a change to the product and/or process that could potentially impact the form, fit, function, quality and/or reliability of the device. The guidelines for requalification tests required are listed in Table
47、4. 4.2.1 Process change notification Supplier will meet the requirements of JESD46 “Guidelines for User Notification of Product/Process Changes by Semiconductor Suppliers“ for product/process notification changes. 4.2.2 Changes requiring requalification All product/process changes should be evaluate
48、d against the guidelines listed in Table 4. JEDEC Standard No. 47J Page 6 4.2 Requalification of a changed device (contd) 4.2.3 Criteria for passing requalification Table 4 lists qualification plan guidelines for performing the appropriate Table 1, Table 2, and Table 3 stresses. Failed devices shoul
49、d be analyzed for root cause and correction; only a representative sample needs to be analyzed. Acceptable resolution of root cause and successful demonstration of corrective and preventive actions will constitute successful requalification of the device(s) affected by the change. The part and/or the qualification family can be qualified as long as containment of the problem is demonstrated until corrective and preventive actions are in place. 5 Qualification tests 5.1 General tests Test details are given in Table 1, Table 2, and Table 3. Not all tests apply to all devi
