1、JEDEC STANDARD 1.5 V +/- 0.1 V (Normal Range) and 0.9 V 1.6 V (Wide Range) Power Supply Voltage and Interface Standard for Nonterminated Digital Integrated Circuits JESD8-11A.01 (Minor Revision of JESD8-11A, November 2005) SEPTEMBER 2007 JEDEC SOLID STATE TECHNOLOGY ASSOCIATION NOTICE JEDEC standard
2、s and publications contain material that has been prepared, reviewed, and approved through the JEDEC Board of Directors level and subsequently reviewed and approved by the JEDEC legal counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstan
3、dings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or i
4、nternationally. JEDEC standards and publications are adopted without regard to whether or not their adoption may involve patents or articles, materials, or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adoptin
5、g the JEDEC standards or publications. The information included in JEDEC standards and publications represents a sound approach to product specification and application, principally from the solid state device manufacturer viewpoint. Within the JEDEC organization there are procedures whereby a JEDEC
6、 standard or publication may be further processed and ultimately become an ANSI standard. No claims to be in conformance with this standard may be made unless all requirements stated in the standard are met. Inquiries, comments, and suggestions relative to the content of this JEDEC standard or publi
7、cation should be addressed to JEDEC at the address below, or call (703) 907-7559 or www.jedec.org Published by JEDEC Solid State Technology Association 2007 2500 Wilson Boulevard Arlington, VA 22201-3834 This document may be downloaded free of charge; however JEDEC retains the copyright on this mate
8、rial. By downloading this file the individual agrees not to charge for or resell the resulting material. PRICE: Please refer to the current Catalog of JEDEC Engineering Standards and Publications online at http:/www.jedec.org/Catalog/catalog.cfm Printed in the U.S.A. All rights reserved PLEASE! DONT
9、 VIOLATE THE LAW! This document is copyrighted by JEDEC and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: JEDEC Solid State Technology Association 2500 Wilson
10、Boulevard Arlington, Virginia 22201-3834 or call (703) 907-7559 JEDEC Standard No. 8-11A.01Page 11.5 V +/- 0.1 V (Normal Range) and 0.9 - 1.6 V (Wide Range) Power Supply Voltage and Interface Standard for Nonterminated Digital Integrated Circuits.(From JEDEC Board ballot JCB-00-20 and JCB-05-79, for
11、mulated under the cognizance of the JC-16 Committee on Interface Technology.)1 ScopeThis standard defines power supply voltage ranges, dc interface and switching parameters for a high speed, low voltage family of nonterminated digital circuits driving/driven by parts of the same family, or mixed fam
12、ilies which comply with the input receiver specifications. The specifications in this standard represent a minimum set of interface specifications for CMOS compatible circuits; however, they also allow limited interoperability with EIA/JESD8-6 compliant HSTL devices.The purpose of this standard is t
13、o provide a standard of specification for uniformity, multiplicity of sources, elimination of confusion, and ease of device specification and design by users. Clause 2.3 describes normal DC electrical characteristics and clause 2.4 (added in revision A) describes the optional chracteristics for Schm
14、itt trigger operation.2 Standard specificationsAll voltages are referenced to ground except where noted.2.1 Absolute maximum continuous ratingsNOTE 1 Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond th
15、ose indicated may adversely affect device reliability. Functional operation under absolute maximum conditions is not implied.NOTE 2 Not to exceed 2.0 V.Supply Voltage, VDD-0.5 V to 2.0 VDC Input Voltage, VIN(except I/O pins) (note 1 and 2) -0.5 V to VDD+ 0.5 VDC Output Voltage, VOUT(including I/O pi
16、ns) (note 2) -0.5 V to VDD+ 0.5 VDC Input Diode Current, IIK(VIVDD) +/- 20 mADC Output Diode Current, IOK(VOVDD) +/- 20 mAJEDEC Standard No. 8-11A.01Page 22.2 Recommended operating conditions2.2.1 Normal rangeNOTE 1 Specified by manufacture to be commercial, industrial, and/or military grade.2.2.2 W
17、ide rangeNOTE 1 Specified by manufacture to be commercial, industrial, and/or military grade.2.3 DC electrical characteristics2.3.1 Normal rangeVDD(min)= 1.4 V and VDD(max)= 1.6 V across operating temperature range - Note 1 and 2NOTE 1 VDDof the sending and receiving devices must track within 0.1 V
18、to maintain adequate DC margins. NOTE 2 For VIHand VIL, VDDrefers to the receiving device. For VOHand VOL, VDD refers to the sending device.Symbol Parameter Operating RangeVDDPower Supply Voltage 1.4 V to 1.6 VTAOperating Temperature Note 1Symbol Parameter Operating RangeVDDPower Supply Voltage 0.9
19、V to 1.6 VTAOperating Temperature Note 1Symbol Parameter Test Condition MIN MAX UnitVDDSupply Voltage 1.4 1.6 VVIHInput High Voltage 0.65 VDDVDD+ 0.3 VVILInput Low Voltage -0.3 0.35 VDDVVOHOutput High Voltage IOH= -2 mA 0.75 VDDVVOLOutput Low Voltage IOL= 2 mA 0.25 VDDVJEDEC Standard No. 8-11A.01Pag
20、e 32.3 DC electrical characteristics (contd)2.3.2 Wide rangeVDD(min)= 0.9 V and VDD(max)= 1.6 V across operating temperature range - Note 1 and 2NOTE 1 VDDof the sending and receiving devices must track within 0.1 V to maintain adequate dc margins. NOTE 2 For VIHand VIL, VDDrefers to the receiving d
21、evice. For VOHand VOL, VDD refers to the sending device.2.4 Optional DC electrical characteristics for Schmitt trigger operation2.4.1 Optional Schmitt trigger operation - Normal rangeVDD(min)= 1.4 V and VDD(max)= 1.6 V across operating temperature range - Note 1 and 2NOTE 1 VDDof the sending and rec
22、eiving devices must track within 0.1 V to maintain adequate dc margins.NOTE 2 For Vt+ (VP) and Vt (Vn), VDDrefers to the receiving device. For VOHand VOL, VDD refers to the sending device.Symbol Parameter Test Condition MIN MAX UnitVDDSupply Voltage 0.9 1.6 VVIHInput High Voltage 0.7 VDDVDD+ 0.3 VVI
23、LInput Low Voltage -0.3 0.3 VDDVVOHOutput High Voltage IOH= -100 uA VDD - 0.2 VVOLOutput Low Voltage IOL= 100 uA 0.2 VSymbol Parameter Test Condition MIN MAX UnitVDDSupply Voltage - 1.4 1.6 VVt+ (VP) Positive Going Threshold VoltageVOUT VOH(min)0.4 VDD0.7 VDDVVt (Vn) Negative going Threshold Voltage
24、VOUT VOH(min)0.35 VDD0.75 VDDVVt (Vn) Negative going Threshold VoltageVOUT VOL(max)0.25 VDD0.65 VDDVVh (Vt) Hysteresis Voltage Vt+ - Vt 0.1 VDD0.5 VDDVVOHOutput High Voltage IOH= -100 uA VDD- 0.2 VVOLOutput Low Voltage IOL= 100 uA 0.2 VDDVJEDEC Standard No. 8-11A.01Page 53 Test conditions for Option
25、al Schmitt trigger operation (contd)Figure 1 DC characteristic measurement circuit of Schmitt Trigger inputJEDEC Standard No. 8-11A.01Page 6Annex A (informative) Differences between JESD8-11A.01 and JESD8-11AThis table briefly describes most of the changes made to entries that appear in this standar
26、d, JESD8-11A.1, compared to its predecessor, JESD8-11A (November 2005). If the change to a con-cept involves any words added or deleted (excluding deletion of accidentally repeated words), it is included. Some punctuation changes are not included.Page Description of change3 In table in 2.4.1, change
27、d the Test Condition units for VOHand VOLfrom “uA“ to “mA“. A.1 Differences betwe en JESD8-11A and JESD8-11This table briefly describes most of the changes made to entries that appear in this standard, JESD8-11A, compared to its predecessor, JESD8-11 (October 2000). If the change to a concept involv
28、es any words added or deleted (excluding deletion of accidentally repeated words), it is included. Some punctuation changes are not included.Page Description of change3 Added subclauses 2.4 and 2.4.14 Added subclause 2.4.24 Added Clause 3 and its subclauses5 Added Figure 1Rev. 9/02 Standard Improvem
29、ent Form JEDEC JESD8-11A.01 The purpose of this form is to provide the Technical Committees of JEDEC with input from the industry regarding usage of the subject standard. Individuals or companies are invited to submit comments to JEDEC. All comments will be collected and dispersed to the appropriate
30、 committee(s). If you can provide input, please complete this form (it can be edited in Acrobat Exchange) and return to: JEDEC Attn: Publications Department 2500 Wilson Blvd. Suite 220 Arlington, VA 22201-3834 Fax: 703.907.7583 1. I recommend changes to the following: Requirement, paragraph number Test method number Paragraph number The referenced paragraph number has proven to be: Unclear Too Rigid In Error Other 2. Recommendations for correction: 3. Other suggestions for document improvement: Submitted by Name: Phone: Company: E-mail: Address: City/State/Zip: Date:
