JUS D E8 003 1-1993 Door leaves - Hard body impact test - Amendment《门扇 硬体冲击检测 修正件》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

ASTM D3006-1999(2004) Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape《氯乙烯塑料压敏电绝缘带》.pdf

ASTM D3006-2010 Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape《聚乙烯塑料压敏电气纸缘带的标准规范》.pdf

ASTM D3006-2010(2017) Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape《聚乙烯塑料压敏电气绝缘带的标准规格》.pdf

ASTM D3012-2007 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven《用炉内样品旋转器测定丙烯塑料的热氧化稳定性的标准试验方法》.pdf

ASTM D3012-2013 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven《使用炉内样品旋转器测定丙烯塑料热氧化稳定性的标准试验方法》.pdf

ASTM D3013-1999(2004)e1 Standard Specification for Epoxy Molding Compounds《环氧基树脂模塑化合物的标准规范》.pdf

ASTM D3013-1999(2012) Standard Specification for Epoxy Molding Compounds《环氧基树脂模塑化合物的标准规格》.pdf

ASTM D3013-2013 Standard Specification for Epoxy Molding Compounds《环氧基树脂模塑化合物的标准规格》.pdf

ASTM D3014-2004a Standard Test Method for Flame Height Time of Burning and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position《硬质热固性泡沫塑料在垂直状态时火焰高度、燃烧时间和质量损失的标准.pdf