JUS N N6 173-1978 Radiocomnmnications Wired distribution systems Methods of measurements Frequency response within a channel《无线电通讯 线缆分布系统 测量方法 电视射频信号的互调制失真比 一个波段内的频率响应》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M4D729-B5-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% MINERAL FILLED MOULDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%矿物填充聚丙烯(PP)均聚物模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSS-M4D729-B7-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% MINERAL FILLED BLOW MOLDING COMPOUND UNDERBODY AND ENGINE TO BE USED WITH FORD WSS-M99P1111-A 《20%矿物填充聚丙烯(PP)均聚物吹塑材料 与.pdf

FORD WSS-M4D731-B1-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%矿物填充聚丙烯(PP)均聚物模塑材料 与福特WSS-M99P1111-A .pdf

FORD WSS-M4D731-B1-2018 POLYPROPYLENE (PP) HOMOPOLYMER 20% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D732-A5-2012 POLYPROPYLENE (PP) HOMOPOLYMER 30% GLASS FIBER REINFORCED MOLDING COMPOUND 25% MINIMUM POST CONSUMER CONTENT TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D732-B2-2014 POLYPROPYLENE (PP) HOMOPOLYMER 30% GLASS FIBER FILLED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D732-B4-2013 POLYPROPYLENE (PP) HOMOPOLYMER 30% GLASS FIBER REINFORCED MOLDING COMPOUND MOLDED IN COLOR INTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D732-B7-2014 POLYPROPYLENE (PP) COPOLYMER 30% GLASS FIBER FILLED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M4D732-B2).pdf

FORD WSS-M4D738-A2-2009 THERMOPLASTIC POLYURETHANE ELASTOMER (TPU) 30% MINERAL GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《30%矿物 玻璃纤维增强的热塑性聚氨酯弹性体.pdf