JUS U A9 004-1987 Modular coordination Storey heights Components and dimensions《模数协调 存储高度 元件与尺寸》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

CSN ISO 8566-5-1994 Cranes Cabins Part 5 Overhead travelling and portal bridge cranes《起重机 小柜 第5部分：桥式起重机和门桥式起重机》.pdf

CSN ISO 8640-2-1993 Textile machinery and accessories Flap warp knitting machines Vocabulary Part 2 Warp let-off fabric take-up and batching《纺织品机械与附件 菲亚特（Fiat）经编机词汇 第2部分：送经，织物卷取和卷布.pdf

CSN ISO 8656-1994 Refractory products Sampling of raw materials and unshaped products Sampling scheme《耐火产品 原料及未定型产品取样 取样方案》.pdf

CSN ISO 8686-1-1993 Cranes Design principles for loads and load combinations Part 1 General《起重机 装载及装载组合设计原则 第1部分：总则》.pdf

CSN ISO 8686-5-1994 Cranes Design principles for loads and load combinations Part 5 Overhead travelling and portal bridge cranes《起重机 装载及装载组合设计原则 第5部分：桥式起重机和门桥式起重机》.pdf

CSN ISO 8688-1-1993 Tool life testing in milling Part 1 Face milling《铣削刀具使用寿命测试 第1部分：面铣刀》.pdf

CSN ISO 8688-2-1993 Metal-cutting tools Tool life testing in milling Part 2 End milling《金属切割刀具 铣削刀具使用寿命测试 第2部分：端铣刀》.pdf

CSN ISO 8769-1994 Reference sources for the calibration of surface contamination monitors Beta-emiters (maximum energy greater than 0 15 MeV) and alpha-emitters《地面污染监测器校准用参考源β 发射器(.pdf

CSN ISO 8791-1-1993 Paper and board - Determination of roughness smoothness (air leak methods) - Part 1 General method《纸和纸板 粗糙度 平滑度测定（气漏方法） 第1部分：一般方法》.pdf