KS 05-224-1980 KENYA STANDARD SPECIFICATION FOR FRUIT SQUASHES《肯尼亚带肉果汁标准规格》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

JUS K T3 060-1983 Snap gauges GO range above 5 to and including 100 mm nominal si e《适用于标称直径为5-100毫米（含）的过端卡规》.pdf

JUS K T3 061-1983 Snap gauges NOTGO range above 5 to and including 100mm nominal si e《适用于标称直径为5-100毫米（含）的不过端卡规》.pdf

JUS K T3 062-1983 Snap gauges GO and NOT GO range above 5 to and including 100 mm nominal si e《适用于标称直径在5-100毫米（含）的过端和不过端卡规》.pdf

JUS K T3 071-1983 GO ring gauges and setting ring gauges from 1 to and including 315 mm nominal diameter《适用于标称直径在1-315毫米（含）的过端环规和校正环规》.pdf

JUS K T3 072-1983 NOTGO ring gauges from 1 to and i ne lud ing 315 mm《适用于标称直径在1-315毫米（含）的不过端环规》.pdf

JUS K T3 075-1983 Sett ng ring gauges from 1 to and including 315 mm nominal diameter《适用于标称直径在1-315毫米（含）的校正环规》.pdf

JUS K T3 111-1983 Tile gauges GO and NOT GO for measures up to including 12 mm nominal si e《适用于标称直径为1-12毫米（含）的孔洞的过端和不过端测量的量规》.pdf

JUS K T3 112-1983 Tile gauges GO and NOTGO for measures over 2 up to and including 8 mm nominal si e《适用于标称直径为2-8毫米（含）的孔洞的测量的过端和不过端量规》.pdf

JUS K T3 113-1983 Tile gauges GO and NOT GO for measures over 12 up to and including 100 mm nominal size《匹配或不匹配公称尺寸在12至100毫米（包括100毫米）之间测量的砖检测仪》.pdf