MSZ 4711 5-1967 《MSZ 4711 5－67小铁路铁水泥路基 间隔压力600mm 轴承压力60kN》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 69882-1-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 1 Designation system technical delivery conditions《符合DIN 69893-1的带锥形空心柄的刀具夹具 第1部分 名称与符号系统、技术交.pdf

DIN 69882-2-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 2 Type A milling cutters with tenon and parallel key drive - Dimensions《符合DIN 69893-1的带锥形空心柄的.pdf

DIN 69882-3-2005 de 9384 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 3 Type B milling machine arbors with enlarged contact surface diameter for milling cu.pdf

DIN 69882-4-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 4 Type C holding fixture for parallel shanks with lateral driving surface - Dimensions《符合DIN .pdf

DIN 69882-5-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 5 Type D holders for parallel shanks with inclined clamping surface - Dimensions《符合DIN 69893-.pdf

DIN 69882-6-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 6 Type E clamping chuck for collets with 8 setting angle - Dimensions《符合DIN 69893-1的带锥形空心柄的刀具.pdf

DIN 69882-7-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 7 Type F expansion clamping chuck - Dimensions《符合DIN 69893-1的带锥形空心柄的刀具夹具 第7部分 F型膨胀夹头 尺寸》.pdf

DIN 69882-8-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 8 Type G shrink chuck - Dimensions《符合DIN 69893-1的带锥形空心柄的刀具夹具 第8部分 G型收缩夹盘 尺寸》.pdf

DIN 69888-2008 Requirements for balancing of rotating tool systems《旋转工具设备的平衡用要求》.pdf